Question about 1998 Mitsubishi Diamante

Open Question

High beams stopped working. Few days later low beams stopped working. Fuses Ok. Headlight low and high work when jumping the relay. Checked all connections in driver door controller, and both electronic boxes below the radio. Any idea to continue troubleshooting?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both my low beam and high beam wont work. And my headlights wont go down even when lights are turned off and the button is unpressed on the inside.


check the headlight relays ,
Check for possible faulty light stalk switch also. Dash lights may fail with this possible cause.
Check fuses

Jan 25, 2016 | 1992 Mazda MX-5

1 Answer

Right front headlight not working on low beam


Have you checked the relays and fuses,high and low beam run on different relays and fuses.

May 07, 2012 | 1995 Ford Explorer

3 Answers

Low beam head lights not working - The low beams, both stopped working. The high beams work fine. I checked the fuses and all 4 are good. I even swapped the low and high beam fises just in case. No...


if the fuses are good then you need to check for power and ground at the headlight plug that attaches to the headlight bulb if you have a good power and ground there and the connections are good then the bulbs are both no good.or if you can tell the bulbs are burnt out by looking at them then you don`t have to check powers and grounds.you also can directly feed power and ground to the bulb and check both the terminals for high beam and low beam as you cannot tell which is which by looking at the terminals

Mar 04, 2011 | 2001 Ford Focus

2 Answers

The low beam lights do not work I have tried a new bulb and replacing the fuses. the high beam lights do work


You may have to check a few items here. Do the high beam lights only work when you "flash" from the combination stalk or do they work when you have headlight switch turned on and then select high beam from stalk..? You may also want to check out the headlight relay. If this is OK, you might have a headlight switch issue or the combination stalk may be faulty.

Feb 28, 2010 | 1984 Porsche 944

1 Answer

Headlites won't come on .all other lites work but, high and low beam don't function.high beam will only operate if I keep the handle of the passing beam up. Have checked the relay system and fuses, All are...


if the high beams function when holding the passing lever, you know the bulbs and fuses are good, the bulbs do operate. the passing lever bypasses the headlight switch on the dash. replace the headlight switch, and be prepared to also replace the connector for this switch, since they had a tendency to melt.

Feb 21, 2010 | 1995 Dodge Dakota

1 Answer

Headlighbeamt cannot work on high beam


It could be in the switch for the low and high beam's

Feb 04, 2010 | 2001 Toyota Camry

1 Answer

1997 Hyundai Accent is acting funny in the headlight department. At first my day-time running lights didn't work and low, high, and flashers were fine. Now, day-time running lights work, high beams work,...


There's only one relay, but two fuses, both located in the underhood fuse/relay box.

53ee18a.jpg Sounds like you have a wiring problem since sometime the left works and the right doesn't, then the right works then the left doesn't. Might be the multi-function switch on the steering column in combination with the connector M10-1, EM01, SE14 & 16.

Jun 26, 2009 | 1997 Hyundai Accent

2 Answers

1994 Mercedes c280 high beams not working...


At first 1994 C280 high beams began to not connect regularly when stick pushed forward, then not at all. Drove high beams by pulling and holding stick back towards steering wheel until that stopped working, too. Shop said the turn signal switch was at fault-- had seen it many times before with W202; about $160 to replace. Haven't done it yet, but should be an easy fix?

May 27, 2009 | 1994 Mercedes-Benz C-Class

2 Answers

Headlights not working


Lihgting switch must also be checked
8673aab.gif

Jun 08, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
1998 Mitsubishi Diamante Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...