Question about 1995 Chevrolet Beretta

1 Answer

I need to get a new pcv elbow connector for 95 chevy beretta v6

I need to get a new elbow connector for the pcv valve.. the rubber L-shaped one that connects directly onto the pcv valve, has only 2 sides/connections.. for a 1995 chevy beretta 6-cyl.. can't find any at the local junk yards or anywhere..

was told you can sometimes get the pcv valve with the elbow already attached, but haven't seen it anywhere..

my funds are tight, so i can't afford to get a whole new $35 line to just replace this $1 part..

help?

Posted by on

  • ctimbers1 Sep 29, 2009

    I actually am using that off one of the old wires now.. it was a little big, so it's clamped on with small hose clamp..

    but in addition to the size being off, i'm told these will melt after a little bit, especially with longer rides?... so i'd really like to find the right part...

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

I have taken a spark plug boot of of a 90 degree boot of the wire and use this it works so check the junk yard for a plug wire with a 90 degree boot on it and pull it off the wire :)

Posted on Sep 29, 2009

  • mike loshbough
    mike loshbough Sep 29, 2009

    This will not melt i had mine on for over 2 years.You may have to walk through a junk yard and just look :)

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 expedition is idling rough and i hear a hiss comming from the engine near the rear but cant tell were its comming from


There is a large elbow shaped tube at the back of the intake plenum where the PCV valve hose connects. This tube gets a hole sucked in it due to oil fumes that come through the PCV valve and softens the rubber. To find the tube,simply follow the PCV valve tube from the valve cover on the passenger side of engine to the back of the intake.

Mar 05, 2015 | 2001 Ford Expedition

1 Answer

Pcv valve elbow


If the piece of hose you have left will reach the pvc valve or extend the hose you can just put it to the valve and if that is not possible then take the "T" and hook to the pvc and put a rubber plug in the open end of the "T".

May 19, 2017 | Pontiac Cars & Trucks

1 Answer

Location of the pvc valve on a 2000 ford crown victoria lx


Look for a elbow shaped tube on the top of the valve cover.
It looks like only a connector but inside of the elbow is the valve.
The elbow shaped PVC valve tends to clog faster than ones that are designed to be straight.

Dec 01, 2010 | 1990 Ford LTD Crown Victoria

1 Answer

Pcv valve 94 v6 xle camry location


I'm not sure exactly where it is but they are always on one of the valve covers. it is shaped like an "L" and will have one vacuum hose connected to it and it inserts into a rubber grommet on the valve cover.

May 28, 2010 | 1994 Toyota Camry

2 Answers

Location of pcv valve on 03 ford focus


http://www.focushacks.com/images/pcv.jpg
Here's a picture to locate it..
So, when looking at the engine from above, on the right of the exhaust.

Procedure to replace it
1) Lift and support the front end of your car, or drive up on ramps
2) Get under the front of your car. The PCV Valve is located behind the exhaust manifold, a few inches below the valve cover.
3) Push up on the PCV valve to pop it out of the tube, or pull. You can get it out of the rubber tube with some effort.
4) Remove the rubber elbow from the top of the PCV valve. This can be re-used if it's not squishy. It can also be replaced cheaply.
5) Put the elbow on the new PCV Valve
6) Re-attach the elbow to the PCV tube
7) Push the new PCV valve back down into the large rubber tube

Sep 25, 2009 | 2003 Ford Focus

1 Answer

Can't find PCV valve on 2000 Chevy Impala 3.8 V6


PCV . Positive Crankcase Ventalation Valves are always located in the valve cover pans with a hose attached usually leading to the air cleaner, or some other vacuum source..

Jun 19, 2009 | 2000 Buick LeSabre

3 Answers

Where is the pcv valve located on a 2003 ford ranger


  • The PCV valve can be located in several places. The most common location is in a rubber grommet in the valve cover. It can be installed in the middle of the hose connections, as well as installed directly in the intake manifold.
  • Once the PCV valve is located, make sure all the PCV system hoses are properly connected and that they have no breaks or cracks.
  • Remove the air cleaner and inspect the air and crankcase filters. Crankcase blowby can clog these with oil. Clean or replace such filters.
  • Oil in the air cleaner assembly indicates that the PCV valve or hoses are plugged.
  • Make sure you check these and replace the valve and clean the hoses and air cleaner assembly.
  • When the PCV valve and hose are in satisfactory condition and there is oil in the air cleaner assembly, perform a cylinder compression test to check for worn cylinders and piston rings.
  • Feb 27, 2009 | 2003 Ford Ranger Regular Cab

    1 Answer

    How do I replace the thermostat in a 95 chevy Beretta 3.1 v6


    you need a socket and a swivel to reach it, the bottom hole in housing is slotted so you won't need to take the bolt all the way out.

    Feb 12, 2009 | 1995 Chevrolet Beretta

    1 Answer

    2002 LINCOLN LS V6 3.0 PCV VALVE LOCATION


    it is down under the intake manifold. the intake manifold must be removed to get to it. this vehicle is known for developing a vacum leak in the elbow hose that connects to pcv valve, so ive done a few.

    Jan 05, 2009 | 2002 Lincoln LS

    1 Answer

    Engine codes Po171 Po174 Po401


    The vast majotity of Ford vehicles with P0171 and P0174 codes are suffering with a vacuum leak. The biggest culprits are the hoses going to the PCV valve. The rubber deteriorates due to heat and oil fumes. Check the hoses and rubber elbows between the PCV valve and the intake manifold. Pay very close attention to the rubber elbows. They crack on the onside and can be hard to spot.

    May 20, 2008 | 2001 Ford Windstar

    Not finding what you are looking for?
    1995 Chevrolet Beretta Logo

    218 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75744 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8123 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...