Question about 1982 Ford Mustang

Open Question

351 ford windsor engine diagram showing front of block with crankshaft center line and all bolt holes on front of block. I want to build a crank support for a friend without him knowing.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing specs for 1969 351 w


The ford 351 Windsor was unique. Due to it's higher performance, they changed the timing on this engine. 1 3 7 2 6 5 4 8 is the timing sequence for your engine. The #1 cylinder is passenger side, front of block.
The 289 and 302 is 15426378

Aug 06, 2014 | Cars & Trucks

2 Answers

Will a f350 with a 460 ci transmission fit in a 95 f150 with a 351ci


I guess the short answer is I doubt it.
The 460 engine should be a big block and the 351 is probably a large 302. I would expect the bolt pattern for the bell housing to be different along with the mounting and the tail shaft.
The 460 should have a bigger drive shaft than the 351.
If you can get the model of the 460 trans a salvage yard should be able to tell you if they will interchange.

Jan 04, 2013 | Ford Cars & Trucks

1 Answer

Need vacuum diagram for EGR valve on 351 Windsor engine


The diagram is under the hood on the Federal Emission Label

Oct 03, 2012 | 1987 Ford F 150

2 Answers

I need the correct firing order diagram for a 1982 ford f150 351 windsor please help at least a link to a site



The firing order is ( 1 - 3 - 7 - 2 - 6 - 5 - 4 - 8 )

The distributor rotor turns COUNTERCLOCKWISE

The marked # 1 position on the distrubutor cap faces to the REAR and slightly towards the drivers side

The engine cylinders / spark plug locations are numbered :


firewall

4 - 8

3 - 7

2 - 6

1 - 5

front

If someone has altered the disstributer, pull #1 plug, put finger over hole, turn engine over until compression on that cyl, line up timing marks (ball park only) and rotor will be pointing at the correct terminal for #1 cylinder plug wire connection, in the cap.

Feb 26, 2011 | 1982 Ford F 150

1 Answer

94 Ford F150 XLT 351 Windsor Engine Vacuum Lines diagram


I have a 94 Ford F-150 and the back up lights don't come on. It is not the bulbs I checked. The fuse panel doesn't have any labeled for them and I can't see any blown. Any thoughts

Sep 04, 2010 | Ford F-150 Cars & Trucks

1 Answer

Ford 351 windsor engine diagram


ford-351-windsor-engine-diagram-p05qnqdskqjeezv3eiltmave-1-0.jpg Here's a mechanical blow-up of an 80's 351w engine.



ford-351-windsor-engine-diagram-p05qnqdskqjeezv3eiltmave-1-2.jpg and the firing order layout.
hope this helps...

Jun 23, 2010 | 1991 Ford Bronco

1 Answer

Looking for a little more power for f250 have 302 4x4 4 speed granny.wondering what it would take to install small block 351


not too much work,the motor mounts-bell housing and crankshaft (for the flywheel off the 302)all should be the same.if the 351 had an automatic transmission,then you will have to add a pilot bearing to the end of the crank (center of crank where flywheel bolts on)..Also it depends on which oil pan is on the new engine--to follow the curve of the frame but should be the same as a 302....302 and 351 windsor engines are the same block except the intake manifold.Just a reminder,truck engines have a better cam for more torque.If the truck is fuel injected you will also have to change the computer which would be located drivers side left upper kick panel.The exhaust manifolds may be different,check them out before starting the procedure.

Jan 16, 2010 | 1982 Ford F 250

1 Answer

I have a 1965 food falcon with a mustang 302 (1978 ) v8. how do i know if it is a windsor or not?


Well there is a 302 cleveland, they are mainly an Australian engine. Identifying one is much like telling the difference between a 351 windsor and a 351 cleveland. Based on the fact that it's from Ford's 335 engine family. 8 cap screws to hold on the valve covers, the block is longer do to the timing chain housing being integrated. The fuel pump bolts are mounted vertically, and the exhaust bolt holes are diagonal. Also, a big difference between an american 302 and an aussie 302 cleveland, is the connecting rods for the cleveland are 6.000''. Where the american 302 connecting rod length is 5.090". Also, referring to a 302 as a windsor is incorrect, it's block families name is the 90 degree v8. The only engine in that family that is properly named the windsor, is the 351 windsor. The 90 degree family also includes the 302 boss. The boss has cleveland style heads, and the block has screw in freeze plugs.

Nov 27, 2009 | 2005 Ford Futura

1 Answer

How many bolts connect the flywheel to the torque converter?


6 bolts connect the flywheel to the crankshaft
If it has an automatic transmission the flexplate or flywheel has 6 bolts to connect it to the crankshaft and 4 more bolts to connect to the torque connverter

Jul 25, 2009 | 1984 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,507 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...