Question about 1999 Mercury Cougar

Open Question

I need to remove the lh headlight from the housing and dont know where to get the tool to do so, nor do i know what it is called.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace a 2000 jeep cherokee laredo headlight bulb. How do you get the headlight fixture out. I removed the screw that I thought was it but it did not budge... CJ


There is no screw involved. You do not remove the headlight housing. Look for wires going to the back of the headlight you should see a plastic retainer nut, take the nut off, pull out the pigtail connector and twist to the left to remove it from headlight housing, then pull the bulb out and replace. No screwdriver or any tools required.
P.S. Your local parts store usually will do this for you or show you how for free. As long as you buy the bulb from them.

Mar 07, 2011 | 2000 Jeep Grand Cherokee

1 Answer

I have a 1985 porsche 911 carrera. I am going to replace the sealed beam headlights with projection lens so I can use H4 bulbs. I have removed the retaining screw on the bottom of the headlight housing...


hello Pat
do you have home an orange peeler tool?Or you just need some kind of flat plastic tool do you can remove the ring without scratching the paint,right ?.
Let me know what housing is stuck ...
proporsche@yahoo.com

proporsche

Feb 05, 2011 | 1985 Porsche 911

1 Answer

1999 Ford Expedition 5.4L Timing chain setup


.
  1. Remove the engine front cover. For additional information, refer to Engine Front Cover in this section.
  1. Remove the crankshaft sensor ring from the crankshaft.
    a0044041.gif
  1. Rotate the crankshaft until the timing mark on the RH camshaft sprocket is approximately at the 11 o'clock position and the timing mark on the LH camshaft sprocket is approximately at the 12 o'clock position.
    a0049532.gif
  1. Using the special tool, position the crankshaft as shown.
    a0041102.gif
  1. Install the special tool.
    aa5423a.gif
  1. NOTE: LH shown; RH similar.
    Remove the two bolts, the timing chain tensioner and tensioner arm.
    aa5952a.gif
  1. Remove the LH and RH timing chains and the crankshaft sprockets.
    • Remove the special tool from the crankshaft.
    • Remove the timing chains from the camshaft sprockets.
    • Remove the right and left timing chains and the crankshaft sprocket from the crankshaft.
    a0029151.gif
  1. ani_caut.gif CAUTION: The bolts are different lengths and must be returned to their original location.
    NOTE: LH shown; RH similar.
    Remove the bolts and the timing chain guides.
    a0044040.gif
Installation
  1. ani_caut.gif CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result.
    ani_caut.gif CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
    Compress the tensioner plunger, using an edge of a vise.
    da0605a.gif
  1. Using a small screwdriver or pick, push back and hold the ratchet mechanism.
    da0606a.gif
  1. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing.
    da0607a.gif
  1. Install a paper clip into the hole in the tensioner housing to hold the ratchet assembly and plunger in during installation.
    a26917a.gif
  1. Remove the tensioner from the vise.
  1. NOTE: There are 61 links in the timing chain.
    If the copper links are not visible, mark two links on one end and one link on the other end, and use as timing marks.
    a0038720.gif
  1. Install the timing chain guides.
    a0044063.gif
  1. Using the special tool, verify correct crankshaft position.
    • Remove the special tool.
    a0041102.gif
  1. NOTE: Crankshaft sprockets are identical. They can only be installed one way. Refer to the following illustration for correct crankshaft sprocket installation.
    If removed, install LH and RH crankshaft sprockets.
    a14824b.gif
  1. Install the LH timing chain onto the crankshaft sprocket, aligning the one copper (marked) link on the timing chain with the slot on the crankshaft sprocket.
    a0041197.gif
  1. Position the LH timing chain on the camshaft sprocket with the two copper (marked) chain links and the camshaft sprocket timing mark aligned.
    a0049191.gif
  1. Position the RH (outer) timing chain on the crankshaft sprocket, aligning the copper (marked) link with the timing mark on the sprocket.
    a0041196.gif
  1. Position the RH timing chain on the camshaft sprocket. Make sure the two copper (marked) links align with the camshaft sprocket timing mark.
    a0041104.gif
  1. NOTE: LH shown; RH similar.
    Position the tensioner arms and tensioners, and install the bolts.
    aa5952a.gif
  1. Remove the tensioner retaining clip.
    a26273a.gif
  1. As a post-check, verify correct alignment of all timing marks.
    a0041106.gif
  1. Remove the special tool.
    aa5423a.gif
  1. Position the crankshaft sensor ring on the crankshaft.
    a0044041.gif
  1. Install the engine front cover. For additional information, refer to Engine Front Cover in this section.


2010&c18=modelyear&c20=n310677&c35=wsm%2ctiming%20drive%20components%2csxj%2c303-01b%2cin-vehicle%20repair&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 03, 2010 | 1999 Ford Expedition

2 Answers

I have a 1999 Ford SHO that needs a new waterpump. I need to know how to replace it and where I can get a schematic of it. Do I need a special tool kit to do it? I'd also like to know where I can get the...


www.autozone.com

They can get all the parts. They also provide haynes repair manuals, any special tools (probably not required for this vehicle) and any special disassembly instructions.

I hope this helps.

Mar 11, 2010 | 2001 Ford Taurus

1 Answer

Where can I find headlights fuse in 1995 Mercury Villager ? I know the fuse box is inside the car under the steering wheel, but that's not for headlights fuse.


IF HAVE AUTOLAMPS
IP FUSE/RELAY PANEL fuse 26 10A & fuse 20 RLY COIL 10A
POWER DISTRIBUTION BOX UNDER HOOD
H/LAMP 15A
.................................................................................................
IF DAYTIME RUNNING
: i/p fuse relay panel fuse 20 RLY COIL 10A
fuse 3 ENGINE CONT 5A

: LH COMPARTMENT FUSE/PANEL
H/LAMP LH 15A
H/LAMP RH 15A
.................................................................................................
WITHOUT DAYTIME RUNNING LAMPS
: LH ENGINE COMPARTMENT FUSE PANEL
H/LAMP LH 15A
H/LAMP RH 15A
: I/P FUSE/RELAY PANEL
#19 TAIL LAMP 15A

Feb 05, 2010 | 1995 Mercury Villager

2 Answers

1999 buick park avenue low-beam headlight out


there are two little brackets you have to pull on to release the bulb housing they are on the top/rear of the housing assembly

Nov 24, 2009 | 1999 Buick Park Avenue

2 Answers

Replace front headlight


Headlights Removal & Installation WARNING
Halogen bulbs contain a gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments.
To help avoid personal injury:
  • Turn off the headlamp switch and allow the bulb to cool before changing bulbs. Leave the headlamp switch off until the bulb change is complete.
  • Always wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • Do not drop or scratch the bulb. Keep moisture away.
  • Place the used bulb in the new bulb's carton and dispose of it properly. Keep halogen bulbs out of the reach of children
To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • LH and RH engine under covers
    • RH and LH Front fender liners
    • Front bumper cover
  3. 2 bolts and disconnect the connectors
  4. Headlight assembly by pulling it forward
  5. To Install:
    1. Install or connect the following:
      • Headlamp assembly
      • 2 bolts and connector
      • Front bumper cover
      • LH and RH front fender liners
      • LH and RH engine under cover
2997275.gif

Jul 25, 2009 | 1998 Toyota Camry

2 Answers

Jeep Grand Cherokee Laredo 1998 headlight assembly instructions


youtube.com type in 1998 grand cherokee headlight assembly, I just fixed mine in 10 minutes, both of them!

Mar 31, 2009 | 1998 Jeep Grand Cherokee

2 Answers

How to change bulb in headligth of volvo v70


For the RH headlight, First remove the top cover of the ECU module just behind the headlight. Then remove the middle section leaving the ECU in place. Both parts are just clipped in so should come out fairly easily. You will then be able to get access the the headlight bulb, release the spring clip at the top (using a mirror helps) and the bulb should come out.
For the LH side remove the air filter housing.

Mar 21, 2009 | 2007 Volvo V70

Not finding what you are looking for?
1999 Mercury Cougar Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...