Question about 1999 Volkswagen Passat

Open Question

Steering pump belt adjustment

Power steering pump belt adjustment

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the power steering belt on a 4g13



ADJUSTMENT

Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.


REMOVAL & INSTALLATION

1.5L, 1.6L, 1.8L, 2.0L and 2.4L Engines


0900c15280037bf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines
Alternator Belt


0900c15280037bf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Loosen the adjuster lock bolt . . .


0900c15280037bf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the alternator belt from the engine

  1. Loosen the alternator support nut.
  2. Loosen the adjuster lock bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the adjuster bolt clockwise until the proper tension is reached.
  3. Tighten the adjuster lock bolt and the alternator support nut.

POWER STEERING BELT


0900c15280037bfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. After the adjusting and fixed bolts are loosened, rotate the pump . . .


0900c15280037bfb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the power steering belt from the engine

  1. Remove the alternator belt as described above.
  2. Loosen the power steering pump adjusting bolts.
  3. Remove the power steering pump fixed bolt on the rear of the bracket.
  4. Rotate the pump toward the engine and remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the pump until the proper tension is reached.
  3. Tighten the adjusting bolts on the pump.
  4. Tighten the fixed bolt on the rear of the bracket.
  5. Install the alternator belt.

A/C COMPRESSOR BELT
  1. Loosen the tension pulley and remove the belt.
  2. The installation is the reverse of the removal.

3.0L DOHC, 3.0L SOHC Galant, and 3.5L Engines


0900c15280037bfc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Serpentine belt routing-Mitsubishi 3.0L engines (except 1998-00 Galant models)


0900c15280037bfd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR

  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the front undercover.
  2. Loosen the tension pulley fixing nut and relieve the tension on the belt by turning the adjusting bolt.
  3. Remove the belt.

To install:
  1. Install the belt on the crankshaft and alternator pulleys.
  2. Using the adjusting bolt on the tensioner, tighten the belt to the desired tension.
  3. Tighten the fixing nut to hold the adjustment.
  4. Install the undercover and lower the vehicle to the floor.
  5. Connect the negative battery cable.

POWER STEERING BELT
  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the undercover.
  2. Remove the alternator and A/C compressor belt.
  3. Lower the vehicle and remove the cruise control pump link assembly.
  4. Place the power steering hose under the oil reservoir.
  5. Loosen the tension pulley fixing bolts and remove the power steering pump drive belt.

To install:
  1. Install the power steering pump drive belt.
  2. Insert an extension bar or equivalent into the opening at the end of the tension pulley bracket and pivot the pulley to apply tension to the belt.
  3. Tighten the fixing bolts.
  4. Raise the vehicle and install the alternator and A/C compressor belt.
  5. Install the undercover and lower the vehicle.
  6. Connect the negative battery cable.

3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.

To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

Mar 21, 2013 | 1996 Mitsubishi Mirage

1 Answer

How do I replace the serpentine belt on a 1999 Kia Sephia?


1.8L Engine
  1. Using a belt tension gauge, measure the drive belt tension and compare with the following specifications:
    1. Alternator belt (new): 86-103 lbs. (383-461 N)
    2. Alternator belt (used): 68-86 lbs. (304-383 N)
    3. A/C compressor and power steering pump belt (new): 110-132 lbs (491-589 N)
    4. A/C compressor and power steering pump belt (used): 95-110 lbs. (422-491 N)

      zjlimited_1999.jpg
      Fig. Using a tension gauge to measure the alternator belt tension - 1.8L engines (click HERE for zoom)


  2. Using the deflection method, apply moderate pressure (about 22 lbs) halfway between the pulleys, and compare with the following specifications.
    1. Alternator belt (new): 0.31-0.35 in. (8-9mm)
    2. Alternator belt (used): 0.35-0.39 in. (9-10mm)
    3. A/C compressor and power steering pump belt (new): 0.31-0.35 in. (8-9mm)
    4. A/C compressor and power steering pump belt (used): 0.35-0.39 in. (9-10mm)
  3. If the specifications fall outside the ranges given, adjust the belt as follows:
    1. Loosen the alternator mounting bolt and adjusting bolt.
    2. Adjust the alternator to get the specified belt deflection.
    3. Tighten the bolts, then recheck the tension.

      zjlimited_2000.jpg
      Fig. Adjusting the alternator belt-1.8L engines

Hope helps.

Oct 09, 2011 | 1999 Kia Sephia

1 Answer

How do I replace the serpentine belt?


1.8L Engine
  1. Using a belt tension gauge, measure the drive belt tension and compare with the following specifications:
    1. Alternator belt (new): 86-103 lbs. (383-461 N)
    2. Alternator belt (used): 68-86 lbs. (304-383 N)
    3. A/C compressor and power steering pump belt (new): 110-132 lbs (491-589 N)
    4. A/C compressor and power steering pump belt (used): 95-110 lbs. (422-491 N)

      zjlimited_1999.jpg

      Fig. Using a tension gauge to measure the alternator belt tension - 1.8L engines (click image for zoom)


  2. Using the deflection method, apply moderate pressure (about 22 lbs) halfway between the pulleys, and compare with the following specifications.
    1. Alternator belt (new): 0.31-0.35 in. (8-9mm)
    2. Alternator belt (used): 0.35-0.39 in. (9-10mm)
    3. A/C compressor and power steering pump belt (new): 0.31-0.35 in. (8-9mm)
    4. A/C compressor and power steering pump belt (used): 0.35-0.39 in. (9-10mm)
  3. If the specifications fall outside the ranges given, adjust the belt as follows:
    1. Loosen the alternator mounting bolt and adjusting bolt.
    2. Adjust the alternator to get the specified belt deflection.
    3. Tighten the bolts, then recheck the tension.

      zjlimited_2000.jpg

      Fig. Adjusting the alternator belt-1.8L engines


Hope helps.

Oct 09, 2011 | 1999 Kia Sephia

1 Answer

What do i do to get new belt on


FOR THE 3.0L ENGINE IF YOU REPLACE AC BELT LOOSEN TOP IDLER PULLEY CENTER BOLT. IF YOU REPLACING ALTERNATOR AND WATER PUMP BELT LOOSEN ALTERNATOR ADJUSTMENT BOLT AND PIVOT BOLT.IF REPLACING POWER STEERING PUMP BELT LOOSEN POWER STEERING PUMP ADJUSTMENT BOLT AND MOUNTING BOLTS.****** FOR THE 2.4L ENGINE TO REMOVE POWER STEERING BELT LOOSEN TOP IDLER PULLEY.FOR ALTERNATOR AND WATER PUMP BELT LOOSEN ALTERNATOR ADJUSTER BOLT, PIVOT AND MOUNTING BOLTS.FOR AC COMPRESSOR LOOSEN LOWER IDLER PULLEY.

Oct 07, 2010 | 1996 Nissan Pickup

1 Answer

How do u change a serpentine belt for a 1999 ford escort zx2


ADJUSTMENT 1.8L Engines ALTERNATOR AND WATER PUMP BELT
  1. Loosen the alternator adjusting bolt.
  2. Raise and safely support the vehicle.
  3. Loosen the alternator mounting bolt. NOTE: Do not pry against the stator frame. Position the prybar against a stronger point, such as the area around a case bolt. Fig. 1: A belt tension gauge should be placed on the longest span of the belt to check tension — 1.8L engine 90981g05.gif

  4. Position a suitable belt tension gauge on the longest accessible span of belt and tighten the belt.
  5. Adjust the tension to 86–103 lbs. (383–461 N) for a new belt or 68–86 lbs. (304–383 kg) for a used belt.
  6. If a belt tension gauge is not available, adjust the tension to 0.31–0.35 in. (8–9mm) deflection for a new belt or 0.35–0.39 in. (9–10mm) deflection for a used belt.
  7. Tighten the alternator adjusting bolt to 14–19 ft. lbs. (19–25 Nm).
  8. Tighten the alternator mounting bolt to 27–38 ft. lbs. (37–52 Nm).
  9. Lower the vehicle. Fig. 2: Alternator and water pump pulley belt routing — 1.8L engine 90981g06.gif
POWER STEERING PUMP BELT
  1. Raise and safely support the vehicle.
  2. Loosen the power steering pump mounting bolt and nuts.
  3. Adjust the power steering pump and, if equipped, the air conditioning compressor belt tension by turning the pump adjusting bolt. Fig. 3: Power steering pump belt routing and locations of the mounting bolts, nuts and adjusting nut — models without A/C 90981g07.gif

  4. Tighten the power steering pump mounting nut near the pump adjusting bolt.
  5. Position a suitable belt tension gauge on the longest accessible span of belt and tighten the belt.
  6. Adjust the tension to 110–132 lbs. (491–589 N) for a new belt or 95–110 lbs. (422–491 N) for a used belt.
  7. Check for proper belt deflection. For a new belt (one with less than 10 minutes of run time), the deflection should be 0.31–0.35 in. (8–9mm). For a used belt (one with more than 10 minutes of run time), the deflection should be 0.35–0.39 in. (9–10mm).
  8. Tighten the power steering pump mounting nut, located near the adjusting bolt, to 27–38 ft. lbs. (37–52 Nm).
  9. Tighten the pump mounting bolt behind the pulley to 27–40 ft. lbs. (36–54 Nm), and the remaining pump mounting nut to 23–34 ft. lbs. (31–46 Nm).
  10. Lower the vehicle. Fig. 4: Power steering pump belt routing and locations of the mounting bolts, nuts and adjusting nut — models with A/C 90981g08.gif
1.9L Engines The accessory drive belt for 1.9L engines has no provision for manual belt adjustment, since these engines use an automatic belt tensioner. Drive belt slack is taken up by the automatic tensioner. NOTE: Movement of the automatic tensioner assembly during engine operation is not a sign of a malfunctioning tensioner. This movement is the tensioner self-adjusting and is required to maintain constant belt tension. Fig. 5: Drive belt routing — 1.9L engines 86751052.gif
2.0L Engines The accessory drive belt for 2.0L engines has no provision for manual belt adjustment, since these engines use an automatic belt tensioner. Drive belt slack is taken up by the automatic tensioner. NOTE: Movement of the automatic tensioner assembly during engine operation is not a sign of a malfunctioning tensioner. This movement is the tensioner self-adjusting and is required to maintain constant belt tension. The belt tensioner has a belt length indicator. If the indicator marks are not between the MIN and MAX marks, the belt must be replaced. Fig. 6: Drive belt routing — 2.0L SOHC engine with A/C 90981g23.gif
Fig. 7: Drive belt routing — 2.0L SOHC engine without A/C 90981g24.gif
Fig. 8: Drive belt routing — 2.0L DOHC engine 90981g25.gif
prev.gif next.gif

Jul 16, 2010 | 1999 Ford Escort

1 Answer

Stiff turning


you could be low on pwer steering fluid. CV joints won't affect steering. That is for powering the wheels.

Very important. Make sure shop did not overtighten a/c belt. If they did, you could be in danger of breaking your crankshaft snout. It may be a good idea to check that.

Also, did they tighten the power steering belt correctly?

Did this steering issue sstart after repairs

go here for help

http://autos.groups.yahoo.com/group/villagerquest/

  1. The tension for the water pump and power steering drive belt should measure 603-691 N (135-155 lbs) for a new drive belt, 495-583 N (110-130 lbs) for a used drive belt. The limit for drive belt tension is 196 N (44 lbs).
    1. Adjust the water pump and power steering drive belt tension as follows:
    2. Raise and support the vehicle.
    3. Remove the RH front fender splash shield (16102).
    4. Loosen the water pump and power steering pump drive belt idler pulley locknut.
    5. Tighten the drive belt tension by turning the water pump and power steering pump drive belt idler pulley adjustment bolt counterclockwise.
      1. Tighten the water pump and power steering pump drive belt idler pulley locknut to 33-37 Nm (24-28 lb-ft).
      1. Install the RH front fender splash shield.
      Deflection Adjustment
      1. NOTE: If the drive belt has been in service for some time, it should be inspected before adjustment. A drive belt that is severely glazed, frayed, cracked, or contaminated with oil must be replaced. Minor cracks in the back of the drive belt are acceptable as long as no large pieces are missing.

        Apply 98 N (22 lbs) of pressure to the drive belt at a point midway between the power steering pump pulley and the water pump pulley.
        1. NOTE: Always check the drive belt deflection when the engine is cold, or has been stopped for at least 30 minutes. A drive belt is considered new if it has been used on a running engine for less than five minutes.

          The drive belt deflection should measure 8-10mm (0.31-0.39 inch) for a new drive belt or 10-12mm (0.39-0.47 inch) for a used drive belt . The limit of deflection is 16.0mm (0.63 inch).
        1. If the drive belt deflection is not as specified, adjust the water pump and power steering pump drive belt tension. Refer to the procedure in this section.
------------------------------------------------------
  1. The tension for the A/C compressor drive belt should measure 603-691 N (135-155 lbs) for a new drive belt or 495-583 N (110-130 lbs) for a used drive belt. The lower limit for drive belt tension is 196 N (44 lbs).
    1. Adjust the A/C compressor drive belt tension as follows:
    2. Loosen the A/C compressor drive belt idler pulley tensioner bolt.
    3. Tighten the A/C compressor drive belt idler pulley adjustment bolt.

May 25, 2009 | 1995 Mercury Villager

2 Answers

Can't get A/C belt around pulleys on my 01 Chevy Tracker 2.5 V6



Removal & Installation

1.6L Engine
A/C Compressor Belt
  1. Disconnect the negative battery cable.
  2. Loosen the A/C compressor mounting bolts.
  3. Pivot the A/C compressor towards the engine in order to relieve the tension on the belt.
  4. Remove the A/C compressor drive belt from the pulleys.

To install:
  1. Properly route and install the A/C compressor drive belt on the A/C compressor, the power steering (if equipped), and the crankshaft pulleys.
  2. Adjust the A/C compressor drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
  3. Tighten the A/C compressor mounting bolts to 13-20 f t. lbs. (18-28 Nm).
  4. Connect the negative battery cable.

Alternator Belt
  1. Disconnect the negative battery cable.
  2. Remove the power steering pump and the A/C compressor drive belt.
  3. Loosen the generator mounting bolts.
  4. Pivot the generator towards the engine and remove the accessory drive belt.

To install:
  1. Properly route and install the generator drive belt on the pulleys.
  2. Adjust the alternator drive belt to obtain 6-8 mm (0.24-0.32 in) deflection for a used belt or 5-6 mm (0.20-0.24 in) deflection for a new belt.
  3. Tighten the generator mounting bolts to 17 ft. lbs. (23 Nm).
  4. Install the power steering and the A/C compressor drive belt.
  5. Connect the negative battery cable.

Power Steering Pump Belt
  1. Disconnect the negative battery cable.
  2. Loosen the power steering pump mounting bolts.
  3. Pivot the power steering pump towards the engine in order to relieve the tension on the belt.
  4. Remove the power steering pump drive belt from the pulleys.

To install:
  1. Properly route and install the power steering pump drive belt on the power steering pump and the crankshaft pulleys.
  2. Adjust the power steering pump drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
  3. Tighten the power steering pump mounting bolts to 22 ft. lbs. (30 Nm).
  4. Connect the negative battery cable.

Apr 26, 2009 | 2001 Chevrolet Tracker

1 Answer

I'm trying to replace the power steering pump on my acura integra 1994 how can i replace it


drain power steering fluid.disconnect the inlet and out let hoses from power steering pump.remove belt by loosen the adjusting bolts on pump bracket.remove power steering bolts and remove pump.put in new power steering pump torque it 17 ft lbs . connect hoses .put belt back on adjust the belt tension. add fluid check level . bleed the air from system.

Apr 13, 2009 | 1990 Acura Integra Hatchback

1 Answer

How to install drive belts to 1996 nissan quest


go here for help
http://autos.groups.yahoo.com/group/villagerquest/files/

392e46a.gif
Item Part Number Description 1 — A/C Compressor Drive Belt Idler Pulley Adjustment Bolt (If equipped)
(Part of 8678) 2 — A/C Compressor Drive Belt Idler Pulley Tensioner Bolt (If equipped)
(Part of 8678) 3 8678 A/C Compressor Drive Belt Idler Pulley (If equipped) 4 8620 A/C Compressor Drive Belt (If equipped) 5 2E884 A/C Clutch Pulley (If equipped) 6 10346 Generator 7 10344 Generator Pulley 8 11719 Generator Adjustment Bolt 9 — Generator Locking Bolt 10 8620 Generator Drive Belt 11 6312 Crankshaft Pulley 12 — Water Pump and Power Steering Pump Drive Belt Adjustment Bolt (Part of 8678) 13 8678 Water Pump and Power Steering Pump Drive Belt Idler Pulley 14 — Water Pump and Power Steering Pump Drive Belt Idler Pulley Locknut (Part of 8678) 15 3A733 Power Steering Pump Pulley 16 8620 Water Pump and Power Steering Pump Drive Belt 17 8509 Water Pump Pulley A — Tighten to 16-20 Nm (12-15 Lb-Ft) B — Tighten to 33-37 Nm (24-28 Lb-Ft)

Mar 28, 2009 | 1996 Nissan Quest

Not finding what you are looking for?
1999 Volkswagen Passat Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...