Question about 1996 Pontiac Grand Am

Open Question

96 GrandAm when car is turned on,you have to shift to 2nd to take off & then you can shift back into drive,what is the problem.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can the TCCM on a 96 blazer 4.3 cause transmission to not shift properly from 2nd into drive and overdrive


It sounds like when you accelerate it downshifts and acts like it is in neutral, when you let off, it shifts back to coast like it is in drive. I would question shift solenoid first. I know this is what 1-2 shift solenoid can act like if you have no low 1 and starts in low 2 or 2nd. There are two solenoids, 1-2nd and 2-3rd. You can drop pan and change them easy.

Jan 17, 2015 | 1996 Chevrolet Blazer

1 Answer

I have a 96 dodge conversion van it won't shift


Bands are adjusted when you first rebuild a unit
& don't wear enough to need readjusting

Most likely time to rebuild it

If that is original, you have gone 17 years,most
don't make 120,000 or ten years

Dec 09, 2012 | Cars & Trucks

1 Answer

Where is the shift solenoid in a 96 oldsmobile regency


There are normally several shift solinoids 1st 2nd, 3rd 4th. one solinoid operates 2 gears. They are located inside the gearbox, you will need to remove the sump & determine which one you need to replace.

Jun 25, 2012 | Oldsmobile Regency Cars & Trucks

1 Answer

What is the mechanic referring to when he says my 96 Kia Sephia might have a broken spider gear? When I'm going forward it shifts real smooth into 2nd gear, then it jerks forward & makes a clunking...


I think he's referring to a gear inside the transmission, part of a planetary gear set. The symptoms point twards a transmission problem, a mount cannot cause this.

Mar 06, 2011 | 1996 Kia Sephia

1 Answer

I have a 96 aurora and every time i drive it wont shift in to 3rd gear


It just won't shift to 3rd or shifts into neutral after 2nd? The 4t80E transmission is known for breaking the bracket that holds the shift solenoids.

Sep 25, 2010 | Oldsmobile Aurora Cars & Trucks

4 Answers

96 chevy blazer 3rd gear and overdrive slipping


i got a 1996 chev. blazer s-s10 4.3 engine 4x4.problem i got is i got 1st 2nd & overdrive & reverse but no 3rd gear what should i do

Jun 30, 2009 | 1996 Chevrolet Blazer

1 Answer

96 taurus shifts out of 1st @3200 then gos to2nd only to gos back


Possible solution:

Too many drivers neglect to change trans fluid or filter until trans is trash.
You might try doing that. Remove the oil pan and install a new filter and clean out the pan gook.
It 's a 25% chance you can drive ok again.

Jun 19, 2009 | 1996 Ford Taurus

1 Answer

96 gmc safari only goes into 2nd gear if i ease off the gas


Does reverse and 4th work? Do you have to back off for it to shift into 4th? 2nd and 4th use the same band to apply.

Jun 11, 2009 | 1996 GMC Safari

4 Answers

GrandAm Tranmission shifts hard


I had the same problem in my 2002 grand am GT. After taking it to a transmission shop and them telling me that I had all this stuff wrong with it that was going to cost me about 2700$ I looked elsewhere. I had an Intake Temperature Sensor that had went bad. It was registering on the check engine light after the fact. I changed it and then found out there was a loose wire in the connector. I fixed that and havent had a problem with it since

Sep 25, 2008 | 2002 Pontiac Grand Am

Not finding what you are looking for?
1996 Pontiac Grand Am Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...