Question about 2001 Nissan Frontier Crew Cab

1 Answer

I have a 01 nissan frontier 3.3 cant get it to fire have already changed the crank sensor and distributor anysuggestions

Posted by on

  • Chris Gennaria May 11, 2010

    is definitely a 'no spark' situation? has fuel and compression?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

The distributor is out of time

Posted on Jul 08, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is and how to change the cranck sensor on 2000 nissan frontier 3.3 4X4.


Hello shalom570,

The crank position sensor is on the rear left-hand side(drivers side) of the engine. See image below.

netvan_185.png

To replace follow steps outlined below.

1. Disconnect crank position sensor harness.
2. Loosen and remove the bolt securing the sensor.
3. Remove the sensor.

To install revers process.

Regards,

Jerry

Aug 20, 2011 | 2000 Nissan Frontier

1 Answer

My 2003 Nissan Frontier stalled and will not crank up when I. Scanned it the P0325 and P0340 codes appeared. How do I fix this?


I would say that the P0340 is causing your no start problem.....This is a cam sensor code......The cam sensor is in the distributor and is not servicable.....I would recommend taking it to a repair shop to properly diagnose the problem before replacing the distributor.

Mar 17, 2011 | 2003 Nissan Frontier Crew Cab

1 Answer

I have a 2000 nissan frontier changed the distributor about a year ago,would not run before that.after i changed it it ran fine,the ob2 codes it threw out cant remember what they were but they led me to...


the next thing i would check is locate all of the ground wires under the hood (grounded to the body) Shiny clean with sand paper and replace. while i am at it I would do the same to grounds to the frame.this may solve your problem . If your grounds are not well connected you will spend many UNESSARY dollars in parts and labour.

Apr 10, 2017 | 2000 Nissan Frontier

1 Answer

After changing a clutch in 06 nissan frontier i now have a spin no start . any suggestions? ps. already replaced crank pos sensor


was flywheel replaced? i've had this happen on one turned out sensor ring distorted on flywheel.went through three until i got a straight one.how did bx look it came in?watch intake cam timing pid while cranking.....should be very close to zero degrees.if not suspect sensor ring damage.l

Jan 19, 2011 | 2006 Nissan Frontier

1 Answer

Truck will not fire. computer said cam sensor but cant find it.


cam sensor is in distributor and not seviced seperately.must purchase distributor assembly.

Jan 16, 2011 | 2000 Nissan Frontier

1 Answer

2000 nissan frontier knock sensor code & distributor


no but the knock sensor does send a signal the ecm and it will ****** or advance the distributor timing

Jun 14, 2010 | 2000 Nissan Frontier

2 Answers

Where's located the engine's computer on 2000 Nissan frontier 3.3


possibly could be in the computer or pcm. check the crank shaft position sensor or knock sensor. is the check engine light on?

Feb 06, 2010 | 2000 Nissan Frontier

2 Answers

2001 Nissan Frontier 4x4 crewcab supercharged. P0340. won't start. also p0325 power to distributor, no spark, resistor ok, coil resistance ok, distributor checks out ok on scope.


P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)
P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)if you have no spark it your cam sensor

Nov 14, 2009 | 2000 Nissan Frontier

Not finding what you are looking for?
2001 Nissan Frontier Crew Cab Logo

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...