Question about Dodge Ram 2500

1 Answer

My cruise control works for about 15 seconds then cuts off. It will not reset until you shut the truck off. Then it just does it again.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 75,797 Answers

Replace the speed control servo assmbly under the hood, it is defective

Posted on Sep 28, 2009

Testimonial: "This has helped me a bunch. Everyone that I have talked to has no answer to my problem. Thank You"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cruise control not working


cruise controls are dependent on the following sensors all working together
brake sensor
clutch sensor
auto--vehicle speed sensor
rpm's sensor
fuse for the cruise control
cruise control switch either or all not working will stop the cruise control from engaging
road speed at which you can engage the cruise control has to be above a reset speed before it will cut in and work

Sep 05, 2015 | 2009 Chevrolet Chevrolet Equinox LS

1 Answer

Cruise control wont engage after restarting vehicle


The fact that the light comes on is a good indication that the electronics are working, the most common problem is a vacumn leak. This can be a damaged or cracked vacumn line, a bad check valve, or the dump switch on the brake pedal

Mar 28, 2015 | 2008 Buick Lucerne CX

1 Answer

Cruse control keep shutting off.


Probably the cruise servo to sensitive to load will need to replace,when you shut off it resets til the next time.

Mar 16, 2015 | 2006 Dodge Ram

1 Answer

Kenworth t800 smart wheel not working


Both the units are controlled by the revs of the engine. Below certain rpms or road speed both will shut off. Replace the switch if that is faulty. If you accelerate the jacke brakes will come off until you lift your foot. Check the circuirtary for the cruise control and you will probably find that it is also controlled as to cut out when the jake brakes are on.

Apr 03, 2013 | Cars & Trucks

1 Answer

Cruise control works until you hit the brakes then you have to shut off and restart the car to reengage.stays working if you use the switch on steering wheel.


Not sure what the question is here. But yes, cruise control disengages when you tap the brake (for obvious reasons). Just reset everything (turn cruise off) then do it again to reengage cruise control.

Aug 03, 2011 | 2000 Chrysler Concorde

1 Answer

Driver side hot passenger side cold


You most likely have a bad Temperature control door actuator on the drivers side. When you select a temperature setting with the dash controls these actuators move the air temperature control doors to match your settings and give the controler feedback on what their position is. If an actuator goes bad it loses it's place and will often end up at the full heat position. Sometimes they will work again for a while if you shut off the vehicle for 15 seconds or so and try again as the actuator will reset and be in the right position again until it stops working once more. Hope this helps and good luck!

Aug 11, 2010 | 2004 GMC Yukon

2 Answers

I own a 2005 GMC Canyon Five CYL and the cruise control stopped working last niight. You push the button and no cruise. I checked the fuse and it is ok I exchanged with another 10AMP and no change still...


Start with the simple and check the fuses and the Stop lamp switch. Check your brake lights, if they're not working, the cruise won't work either. If they're not working, check the fuse for them, if the fuse is fine, then take it into the dealer, there's been a recall issued on the brake switch, so it should get fixed for free.
Cruise Control Disengaged
The powertrain control module (PCM) disengages the cruise control operation based on the signals from the following switches:

* The stop lamp switch
* The TCC brake/cruise release switch
* The clutch release switch, if equipped
* The cruise control On/Off switch

The TCC brake/cruise release switch and the stop lamp switch are mounted on the brake pedal bracket. When the brake pedal is applied, the normally closed TCC brake/cruise release switch opens and the normally open stop lamp switch closes. The PCM detects a low signal voltage on the TCC brake/cruise release switch signal circuit and a high signal voltage on the stop lamp switch signal circuit. When the clutch pedal is applied, the normally closed clutch release switch opens and the PCM detects zero voltage on the CCP switch signal circuit. The vehicle speed stored in the memory of the PCM will be erased when the cruise control On/Off button is turned OFF, or the ignition switch is turned OFF.

The Cruise Control System will disengage when the PCM detects that a driver override function has been active for approximately 60 seconds .

When the Cruise Control System is disengaged, the PCM sends a class 2 message to the instrument panel cluster (IPC) in order to deactivate the cruise control indicator.

Cruise Control Inhibited
The powertrain control module (PCM) inhibits the cruise control operation when any of the following conditions exist:

* A cruise control related DTC has been set.
* The vehicle speed is less than 40.2 km/h (25 mph) .
* The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear.
* The engine RPM is too low.
* The engine RPM is too high, with fuel cut off.
* The vehicle speed is too high, with fuel cut off.
* The system voltage is not between 9 volts and 16 volts .
* The Traction Control System (TCS) is active for more than 2 seconds .

Thank you for using Fixya and start with replacing the stop lamp switch. Even though the brake light work, it;s been known for that switch to cause your issue. that's way there was a recall for it.

Apr 01, 2010 | 2005 GMC Canyon

1 Answer

Cruise control light will not come on after truck warms up 2004 dodge ram pick-up Cruise works ok when first using it , after driving to my destination, shutting off the truck. 15 min later driving again,...


After the light goes out does it come back on while driving down the road?
If it does this sounds as if you may have a heat sensitive problem at the cruise motor. this has a sensoe that turns the light on when it is engaged. when you turn it off and sits a while does the heat under the hood goes higher expanding the circuts an open circut. You may have to replace the board in the motor.

Aug 19, 2009 | 2004 Dodge Ram 1500

1 Answer

Cruise control shuts off up hill


if the cruise control light has come on then i would take it to a dealer and have them hook it up to the scan tool and see what exactly is going on. I think that pretty much is going to be your BEST bet. However you should check your brake fluid because if your brake fluid is too low then the cruice control will not work.

Jun 10, 2009 | 2004 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...