Question about 1996 Isuzu Rodeo

Open Question

Yes I have a 1996 Rodeo I just rebiult the motor and I am not sure if I have the timing belt right can it be 180 out of time I have no power the book I have is not very good want to make sure it is right>

Posted by on

  • Chris Gennaria May 11, 2010

    it is possible to be 180 deg out. are the timing marks by the cam/crank sprockets not visible?

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 109 Answers

SOURCE: 98 4 cyl isuzu rodeo timing belt

I looked in my database but can't help with that one.

Posted on Nov 21, 2008

  • 87 Answers

SOURCE: Harmonic balancer bolt direction for loosening??

CCW , and your going to at least put the new timing belt on and balance to check for compression. you can run an engine without the covers installed or accessories hooked up

Posted on Feb 07, 2009

  • 28 Answers

SOURCE: no power to fuel pump 1996 isuzu rodeo

well i got a salvaged ecm from a junkyard and put it in, still did'nt start. took alternator off to have it checked , it is fine. put it back in and now it starts and runs fine. check the alternator and the connections, i heard the alternator controls power after the initial ecm prime when it is turned on. i have no idea how true it is, but worth a shot. if you can find a cheap ecm for a junkyard (mine was 75 bucks) i would try that afterwords.

Posted on Mar 06, 2009

stevenhurc
  • 450 Answers

SOURCE: trouble getting marks aligned on 2001 Izusu Rodeo

if its a 6VE1 engine you might want to remove rocker covers and put front lobes of camshafts in position shown in picture with cam gear timmed up at same point cam gear are 3:1 ratio


b76b855.jpglook closely at cam gears in pic to see front lobe positions for both banks

Posted on Jul 30, 2009

  • 1757 Answers

SOURCE: i need diagram for 2.2 l for isuzu rodeo timing

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following 2 LINKS. They have the Serpentine and Timing Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies:
For the Serpentine Belt:
http://www.2carpros.com/car_repair_information/year/1998/make/isuzu/model/rodeo/1998_isuzu_rodeo_drive_belt_routing_diagram.htm
For the Timing Belt:
http://www.2carpros.com/car_repair_information/year/1998/make/isuzu/model/rodeo/1998_isuzu_rodeo_timing_belt_diagram_marks.htm

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 2.3L 4W ISUZU RODEO HOW DO YOU GET IT BACK IN TIME


Remove timing belt cover and the timing belt. Line up the cam gear timing mark with the mark that is behind it. Then, set the crankshaft pulley timing mark to zero degrees or whatever the book says. Then re-install the timing belt and re-torque the timing belt tensioner to the proper torque. Turn the engine one full turn, with a breaker bar and socket. Re-check the timing marks on the crankshaft and camshaft. Re-install the timing belt cover and everything else you took off to get to the belt. Be sure to torque the crankshaft pulley bolt to specs.

Sep 27, 2014 | 1995 Isuzu Rodeo

1 Answer

2000 hyundai accent. car ruan great right up to the point of the timing belt breaking.


It could be off 180, if making a bad knocking sound then yes piston is probibly out but turn ur distributor rodar 180 degrees or even 360 because u may be on your compression stroke when u need to be on exsaust. Double check your marks on belt might be off a tooth.

Dec 07, 2012 | Cars & Trucks

2 Answers

I changed my timing belt, water pump and I belive the harmonic tensioner when my rodeo turned 100k. A year later I heard a knocking noise coming from the area where the timing belt is located. The noise...


Yes its the correct name. Yes it should have been replaced..... but its up to the mechanics advice and the customer. its not normally replaced, but I replace all parts including the water pump, just as a matter off service, to avoid your exact problem.

Dec 20, 2010 | 1999 Isuzu Rodeo

1 Answer

Just replaced a timing belt due to it ripping. Timed it per the book, have 125 lps compression, yet it will not start. Could I have timed it on the exhaust stroke and not the compression?


yep,, It happens,, remove the number one plug,, bring it up to TDC,, and look to see where the timing is set,, it may be 180 off

Aug 03, 2010 | 1996 Toyota Camry

1 Answer

I'D LIKE TO GET THE SCHEMATICS FOR 1996 ACURA TL 3.2 TIMING BELT


Hope these are the ones you are looking for!


33ce675.gif
Loosen the adjuster bolt 180 degrees


2e7fa97.gif
Aligning the timing marks


ec49290.gif
Positioning the left camshaft


ec6a898.gif
Positioning the right camshaft


f8007f6.gif
Proper timing belt routing is essential


fabcbfd.gif
Check to be sure the crank and cam pulleys are at TDC


67ec287.gif
Exploded view of the timing belt and related components

May 25, 2010 | 1996 Acura TL Series

2 Answers

Is it necessary to take the timming belt off to replace the water pump on a 1996 isuzu rodeo


3.2L engine, you will have to remove timing belt to replace water pump, your water pump is timing belt driven, I would replace timing belt while in there, good luck, hope this was very helpful.

May 14, 2010 | 1996 Isuzu Rodeo

1 Answer

I HAVE 1996 ISUZU . tIMING CHAIN BROKE. i AM REPLACING CHAIN AND GEARS. REPAIR BOOK SAYS TO ALIGN MARKS ON GEARS WITH TENSIONER MARKS. DO I ALSO HAVE TO MAKE SURE #1 PISTON IS ON COMPRESSION STROKE OR NOT?


Yes be sure the number one piston is at TDC firing stroke or compresson stroke and line up the timing mark pointer is pointed at exactly zero. One more thing when aligning the camshaft sprocket or sprockets be sure that when you are rotating the sprocket for the cam it is rotating in the correct direction and also be sure you observe the intake valve for number one shutting as you bring the marks up to alignment points, the intake valve and the exhaust valve should be shut when the marks line up if not you could have the cam sprocket off 180 degrees, get it right the first time or you may damage a valve trying to start.

Dec 29, 2009 | 1997 Isuzu Hombre

1 Answer

Water pump replacement 96 isuzu rodeo


Remove belt, fan, fan shroud and fan bracket. Remove timing covers, timing belt and water pump. Replace timing belt and the hydraulic tensioner with new ones. I suggest you get a mechanic to do this as you can easly get it out of time. Not an easy job.

Jul 03, 2009 | 1996 Isuzu Rodeo

1 Answer

Harmonic balancer bolt direction for loosening??


CCW , and your going to at least put the new timing belt on and balance to check for compression. you can run an engine without the covers installed or accessories hooked up

Feb 05, 2009 | 1996 Isuzu Rodeo

2 Answers

Mazda 626 timing


If the timing was 180 out it wouldn't run at all.
Do a compression test to make sure all the cylinders are in good condition, go back over your timing and make sure you aren't overlooking something like two plug leads swapped?, it sounds like it's only firing on two.

Aug 17, 2008 | 1996 Mazda 626

Not finding what you are looking for?
1996 Isuzu Rodeo Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...