Question about 1989 Mitsubishi Galant

1 Answer

I need a fuel tank complete with fuel pump etc. & any necessary fittings that go with the tank.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Mitsubishi Master
  • 79,865 Answers

I am sorry but we are a techanical advice site, no resources for parts, suggest u do a slavage yard search using google, here is a link to web site that can help you.

Posted on Sep 28, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need to know how to disconnect the fuel lines from the fuel pump to replace the fuel pump

  • Park your Chevy Tahoe in a safe place with a level surface and plenty of room for you to work around the vehicle. Open the hood and disconnect the black, negative battery cable.
  • Relieve the fuel system pressure. Loosen the fuel filler cap and depress the small stem inside the fuel pressure Schrader valve. The valve is similar to an air valve on a bicycle tire and is located on the fuel inline rail in the engine compartment right before the first fuel injector. Use a small screwdriver to depress the stem while covering the valve with a shop rag to catch the squirt of fuel.

  • Drain the fuel tank through the fuel filler hose using a hand siphon pump if necessary.
  • Raise the rear of the vehicle using a floor jack and safely support it on two jack stands.
  • Remove the evaporative emission (EVAP) canister located next to the fuel tank. Use a wrench or ratchet and socket.
  • Disconnect the chassis fuel lines leading to the fuel tank by pressing the lock tabs and pulling the lines off their fittings. Plug the fuel lines with clean shop rags to prevent fuel system contamination.
  • Disengage the EVAP line from the clip at the side of the tank, opposite the frame rail. Support the fuel tank with jacks if necessary and remove the two fuel tank straps using a ratchet and socket; then lower the rear of the fuel tank slightly. If necessary, disconnect the fuel filler hose from the tank by removing the hose clamp at the tank.
  • Disconnect the fuel pump electrical connectors, lower the tank and disconnect the fuel lines from the fuel/sending assembly on the tank.
  • Clean the area around the pump/sending unit assembly. Disconnect the pump/sending unit by unlocking the cam lock. With a long punch and a light hammer, turn the cam lock counterclockwise. After releasing the cam lock, lift the pump/sending unit assembly off the tank and replace the old pump with the new unit.

  • Dec 04, 2010 | 1999 Chevrolet Tahoe

    2 Answers

    Where is the fuel pump on a 1995 Nissan PU

    see instructions from AutoZone:
    The fuel pump assembly is located in the fuel tank. Refer to the fuel tank assembly illustrations in this section. On most applications, the fuel tank must be lowered to remove the fuel pump assembly. The fuel pump assembly is cooled by the fuel in the tank.


    See Figure 1
    1. Before disconnecting the fuel lines or any of the fuel system components, release the fuel system pressure as described previously in this section. Releasing system pressure is a very important step for the correct removal of the electric fuel pump.

    0900c1528018d240.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Internal view of the electric fuel pump
    1. Disconnect the negative battery cable. Unfasten the fuel pump assembly electrical connector and remove the fuel tank inspection cover.

    If the truck has no fuel tank inspection cover, the fuel tank must be lowered or removed to gain access to the in-tank fuel pump.
    1. Disconnect the fuel outlet and return hoses. Remove the fuel tank assembly, if necessary.
    2. Remove the ring retaining bolts and the O-ring, then lift the fuel pump assembly from the fuel tank. Plug the opening with a clean rag to prevent dirt from entering the system.

    When removing or installing the fuel pump assembly, be careful not to damage or deform it. Always install a new O-ring.
    To install:
    1. Install the fuel pump assembly in the fuel tank with a new O-ring. Install the ring retaining bolts. Install the fuel tank if removed.
    2. Reconnect the fuel lines and fasten the electrical connection.
    3. Connect the battery cable, then start the engine and check for fuel leaks.

    The "Check Engine Light'' may stay on after installation is completed. If so, the trouble code in the control unit's memory must be erased. To erase the code, disconnect the battery cable for 10 seconds, then reconnect it a verify that the light is extinguished.


    See Figures 2 and 3
    1. Relieve the fuel system pressure, as described previously in this section.
    2. Disconnect the fuel inlet hose at the electro injection unit.

    0900c1528018d241.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Make sure that the fuel line hose clamps are installed properly

    0900c1528018d242.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Testing fuel system pressure using a gauge and a "T'' fitting
    1. Install a fuel pressure gauge.
    2. Start the engine and check the fuel line for leakage.
    3. Read the pressure on the pressure gauge. The gauge should read approximately 36.3 psi (250 kPa).
    4. Relieve the fuel system pressure again.
    5. Remove the pressure gauge from the fuel line and reconnect the fuel inlet hose.

    Aug 25, 2010 | 1995 Nissan Pickup

    1 Answer

    How do I remove fuel pump off 01 olds silhouette. Dropped the tank down already

    2001 Oldsmobile Truck Silhouette 3.4L SFI 6cyl
    Fuel Pump - Removal & Installation
    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Properly relieve the fuel system pressure.
    3. Drain and remove the fuel tank from the vehicle
    4. Remove or disconnect the following:
      Negative battery cable Quick-connect fittings at the fuel pump Fuel pump locking nut with a Fuel Pump Spanner Wrench J 39348 Fuel pump assembly from the fuel tank and discard the O-ring
    To install:
    1. Install or connect the following:
      New O-ring on the fuel tank Fuel pump into the fuel tank making certain not to fold or twist the strainer and that it does not interfere with the full travel of the float arm Fuel pump locking nut with the scanner tool Quick-connect fittings at the fuel pump Fuel tank and fill the tank Negative battery cable
    2. Prime the fuel system as follows:
      1. Turn the ignition switch ON for two seconds.
      2. Turn the ignition switch OFF for 10 seconds.
      3. Turn the ignition switch ON and checks for leaks. Repair if necessary.

    Fuel Pump/SenderRemoval & Installation
    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Properly relieve the fuel system pressure.
    3. Disconnect the negative battery cable.
    4. Drain the fuel tank into an approved container.
      WARNING Do not attempt to straighten any kinked nylon fuel lines. Replace any kinked nylon fuel feed or return pipes in order to prevent damage to the vehicle.
      WARNING Do not attempt to repair sections of nylon fuel pipes. If the nylon fuel pipes are damaged, replace the pipes.
    5. Raise the vehicle.

      Fig. Showing the fuel tank assembly and related components
    6. Disconnect the fuel supply pipe (5) quick-connect fitting.
    7. Disconnect the evaporative emission (EVAP) purge pipe (6) quick connect fitting at the EVAP canister.
    8. Loosen the fuel tank filler pipe hose clamp.
    9. Disconnect the fuel tank filler from the fuel tank.
    10. Disconnect the vapor recirculation pipe from the filler tube.
    11. Remove the fuel tank shield.
    12. With the aid of an assistant, support the fuel tank.
    13. Remove the fuel tank strap attaching bolts.
    14. Disconnect the fuel sender and the fuel tank pressure (FTP) sensor electrical connectors at the body pass through.
    15. Remove the fuel tank from the vehicle.
    16. Remove the fuel sender assembly (3).

      Fig. Identifying the fuel sender assembly
    17. Disconnect the fuel sender electrical connections (3).
    18. Clean all of the fuel pipe connections, all of the hose connections, and all of the areas surrounding the connections before disconnecting the connections in order to avoid possible contamination of the fuel system.
    19. Disconnect the fuel supply pipe quick-connect fitting (4) at the fuel sender assembly.
    20. Disconnect the evaporative emission (EVAP) pipe quick-connect fittings (5, 6) at the fuel sender assembly.
      CAUTION Do NOT use impact tools. Significant force will be required to release the lock ring. The use of a hammer and screwdriver is not recommended. Secure the fuel tank in order to prevent fuel tank rotation.


    Jun 23, 2010 | 2002 Oldsmobile Silhouette

    1 Answer

    My 1988 Nissan Sentra E16i will not run. The Engine turns over and may start to run but slowly begins to cough before dying. There is very old fuel in the tank but I have added a fuel stabilizer and mixed...

    Water condenses in tanks not completely full & petrol degrades to "near enough" kerosine if left for too long. Also lacquer in the petrol forms a film on filters etc. So you probably have a system filled with water & lacquer now. Suggest drain tank & full flush of lines & filters.
    Injectors (if fitted) may need cleaning too. It ran before all the gunk worked loose and clogged everything.

    May 27, 2010 | 1988 Nissan Sentra 2 Door

    1 Answer


    Sorry not sure what you are trying to do exactly. Change the fuel pump in the fuel tank? I'm posting because I recently had to do my Jaguar, maybe familiar.

    I had to lower the entire rear suspension, wheels, differential and trailing arms. This allowed me to disconnect fuel lines going into middle bottom of fuel tank. Then I could continue removing fuel tank thru trunk including the filler neck. Then I could finally get to top of fuel tank and remove clips to remove fuel pump in tank. Funny how the instructions want you to empty the tank before you start. I had to do it with about 1/2 tank, how was I supposed to empty 10 gallons of fuel?
    Good luck!

    Mar 15, 2010 | 2003 Volvo XC90

    1 Answer

    How do I change 88 seville fuel pump

    The pump is located in the fuel tank. Tank must be dropped to gain access & you do that by removing the staps & carefully lowering the tank. On top of the tank, the retaining ring has to be removed, hoses disconnected carefully, and the entire fuel pump assembly with the float & low fuel warning sensor (if equipped) will be removed .

    Important to note the position of the hoses, wiring, and the mounting position of the pump and the retaining ring as it fits into the tank. Mark items to identify where to return them to once done. Pictures with a digital camera are good to have when needing to review how things were.

    Not a bad idea to replace the in-line fuel filter when replacing the fuel pump assembly, fill it as full as possible with fuel injector cleaner before reinstalling the hoses & you'll get a good injector cleaning as well.

    good luck

    Feb 14, 2010 | 1988 Cadillac Seville

    1 Answer

    REPLACEMENT of a fuel filter on a 1997

    The fuel filter (1) is mounted next to the fuel pump module (2), on top of the fuel tank (3)

    The fuel delivery system uses quick-connect fittings. The fuel filter mounts to the top of the fuel tank.
    1. Properly relieve the fuel system pressure.
    2. Disconnect the negative battery cable.
    3. Raise and safely support the vehicle.
    4. Place a drain pan underneath the fuel filter to catch any spilling fuel that will result from disconnecting the fuel lines.
    It may be necessary to support the weight of the fuel tank with a block of wood and a floor jack. Once this is accomplished, loosen, but do not remove, the fuel tank strap bolts. Allow the fuel tank to lower just enough to access the fuel line fittings at the fuel pump module.


    Disengage the fuel line quick-connect fittings from the fuel pump module

    Be sure to place a drain pan underneath the filter line fittings to catch all fuel spillage

    Locate the fuel filter in its mounting on top of the fuel tank. Detach the quick-connect fittings from the chassis fuel supply tube and fuel pump module by squeezing the quick-connect fitting retainer tabs together and pulling the fitting assembly away from the fuel line nipple. The retainer will remain on the fuel tube.

    Using a 10mm socket, remove the fuel filter mounting bolt ...

    ... then remove the fuel filter from the top of the fuel tank

    1. Remove the fuel filter mounting bolt and remove the fuel filter from the fuel tank.
    To install:
    1. Install the fuel filter on the top of the fuel tank and tighten the mounting bolt.
    2. The fuel supply tube (to chassis fuel line), return tube (to pump module) and fuel supply (to fuel filter) tube are permanently attached to the fuel filter. The quick-connect fitting ends of the fuel supply and return tubes are of different sizes.
    3. Apply a light coating of 30W engine oil to the nipples of the fuel filter.
    4. Push the quick-connect fitting over the fuel line until the retainer seats and clicks into place. Be sure the retainer tabs have locked into the case of the fitting.
    5. If necessary, raise the fuel tank and tighten the fuel tank strap bolts.
    6. Lower the vehicle. Start the engine and check for leaks.

    Nov 30, 2009 | 1997 Chrysler Town & Country

    1 Answer

    How to replace fuel pump on chevy malibu 2000

    First you should check your trunk. some newer chevy's have an access pannel uner the trunk liner inside the trunk. you remove the liner, remove the bolts and panel, and the pump is right there. it may take some effort to get it wiggled through, but trust me, it will fit. you must remove the fuel lines and wire harness first, then remove the lock ring completely before attempting to pull the pump through the access hole. if that fails then you need to drop you fuel tank to access the pump. there are instructions for removal and installation of the tank below.

    1. Disconnect the negative battery cable.
    2. Drain the fuel tank, using a hand-operated pump device to drain as much fuel through the filler tube as possible.

    0900c1528026905d.jpg Fig. View of fuel tank mounting

    0900c1528026905e.jpg Fig. The fuel filler pipe is attached to the body with a bracket and retaining bolt

    0900c1528026905f.jpg Fig. The fuel filler pipe is attach to the tank by a hose clamp
    1. Raise and safely support the vehicle.
    2. Unfasten the muffler hanger bolts.
    3. Remove the rubber exhaust hangers, then allow the exhaust system to rest on the rear axle.
    4. Disconnect the hoses from the fuel tank sender. Grasp the filter and one nylon fuel connection line fitting. Twist the quick-connect fitting 1 / 4 turn in each direction to loosen any dirt within the fitting. Repeat for the other fitting. Using compressed air, blow out the dirt from the quick-connect fittings at the end of the fuel filter.
    5. Detach the quick-connect fittings by pulling the release tabs back on the fuel line quick connector and pulling apart.
    6. Disconnect the hoses at the tank from the filler, vent and vapor pipes.
    7. With the help of an assistant, support the fuel tank, then disconnect the two tank retaining straps and carefully lower the tank.
    8. Detach the fuel sender electrical connector.
    9. Unplug the fuel pressure sensor connector.
    10. Remove the fuel tank from the vehicle.

    To install:
    1. If the tank is being replaced, perform the following:
      1. Remove the sound insulators.
      2. Remove the modular fuel pump/sender assembly, as outlined earlier in this section.
      3. Inspect all connectors for dirt and burrs. Clean or replace, as required. Inspect the fuel line O-rings for cuts, nicks, swelling and/or distortion and replace as necessary.
      4. Install the fuel sender assembly to the new tank, as outlined earlier in this section.
      5. Install the sound insulators.

    2. With the help of an assistant, raise the fuel tank to the vehicle and attach the fuel sender connector and, if equipped, the fuel pressure sensor connector.
    3. Raise the fuel tank into position then fasten the retaining straps. Tighten the retaining bolts to 26 ft. lbs. (35 Nm).
    4. Connect the hoses to the filler, vent and vapor pipes.
    5. Attach the nylon fuel feed and return connecting line quick-connect fittings to the fuel sender, as follows:
      1. Apply a few drops of clean engine oil to the male connector tube ends.
      2. Push the connectors together to cause the retaining tabs/fingers to snap into place.
      3. Once installed, pull on both ends of each connection to be sure they are secure.

    6. Install the rubber exhaust hangers.
    7. Install the muffler hanger bolts, then tighten to 11 ft. lbs. (15 Nm).
    8. Attach the fuel tank sender electrical connector.
    9. Carefully lower the vehicle.
    10. Refill the fuel tank, then connect the negative battery cable.
    11. Turn the ignition to the ON position for two seconds, then turn it to the OFF position for ten seconds. Turn again to the ON position and check for fuel leaks.

    Nov 04, 2009 | 2000 Chevrolet Malibu

    1 Answer

    How to replace fuel pump 91 lesabre

    Removal & Installation The fuel pump is located in the fuel tank. The fuel tank must be removed from the vehicle in order to access the pump.
    1. Properly relieve fuel system pressure.
    2. If not already done, disconnect the negative battery cable.
    3. Raise and safely support the vehicle.
    4. Safely drain and remove the fuel tank assembly, as outlined later in this section.
    5. If necessary, detach the quick-connect fittings from the fuel sender assembly and remove the fuel lines.
    6. Remove the fuel gauge sender and pump assembly by turning the cam locking ring counterclockwise. It may be necessary to use a spanner wrench, such as tool J-24187, to perform this.
    7. Carefully lift the assembly from the fuel tank, then remove the fuel pump from the fuel gauge sender unit.
    8. Remove the sender O-ring from the top of the sender and discard.
    9. Disconnect the pump wires, hose clamps and the clamp from around the pump body.
    10. Pull the pump assembly out of the rubber connectors.
    11. Inspect the fuel pump attaching hose for any signs of deterioration, and replace as necessary.
    12. To install:
      1. Push the fuel pump assembly into the attaching hose. Attach the pump electrical wires and fasten the hose clamps to the attaching hose and around the pump body.
      2. Place the fuel tank sender and pump assembly into the fuel tank. Use a new O-ring seal during assembly.
      3. Place the cam lock over the assembly, then lock by turning clockwise, using a suitable spanner wrench, if necessary.
      4. If removed, attach the fuel sender fuel line quick-connect fittings.
      When installing the fuel tank, make sure all rubber sound isolators or anti-squeak spacers are replaced in their original locations.
      1. Install the fuel tank, as outlined later in this section.
      2. Refill the fuel tank.
      3. Connect the negative battery cable.
      4. Turn the ignition switch to the ON position to pressurize the fuel system and check for leaks.

    Oct 10, 2009 | 1991 Buick LeSabre

    3 Answers

    Fuel pump problems

    Some fuel pumps can be purchased and replaced by themselves. Other electric fuel pumps are combined with the fuel tank sending unit, and can only be replaced as a unit. ( as I believe your might be ). More expensiove this way, but thats how cars have become. Lucky you dont't have to buy the whole fuel tank, pump, and sender, as a unit. Hope this helps

    May 08, 2009 | 2002 Chevrolet Blazer

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    26 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Experts


    Level 3 Expert

    79865 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8836 Answers

    Are you a Mitsubishi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides