Question about 1994 Dodge Dakota Club Cab

Open Question

Rh brake and turn signal will not work - 1994 Dodge Dakota Club Cab

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All my lights work on my 2005 ford focus except the lower brake lights and turn signals. all fuses are good.


Do you know anything about automotive electronics ?
Stoplamps
The stoplamps are part of the rear lamp assembly. When the brake pedal is applied, the stoplamp switch supplies voltage to the generic electronic module (GEM) and the high mounted stoplamp. The GEM then supplies voltage to the rear lamps.

Turn Signal Lamps and Hazard Warning Lamps
The turn signal lamps and hazard warning lamps system consists of:
  • Hazard switch
  • Multifunction switch
  • GEM
  • Turn signal lamps
When the multifunction switch is placed in the LH or RH turn positions, a voltage signal from the GEM is routed to ground. When the GEM detects the multifunction switch in the LH or RH turn position, the GEM supplies voltage to the appropriate turn lamps in a flashing manner. When operating correctly, the turn lamps flash approximately 80 times per minute.
When the hazard warning switch (located in the upper part of the center console) is switched on, a voltage signal from the GEM is routed to ground. When the GEM detects that the hazard switch is switched on, the GEM supplies voltage to all the turn signal lamps in a flashing manner. When operating correctly, the hazard lamps flash approximately 80 times per minute.

Do you know how to test electrical circuits with a DVOM - digital volt ohm meter , how to read an use a wiring diagram to pin point locations in a electrical circuit for testing B+ voltage an ground ?

Free wiring diagrams
http://www.bbbind.com/free_tsb.html Enter your vehicle info . year ,make , model an engine size . Under system click on lighting ,then under subsystem click on turn signal lamps . Click the search button then each blue link , one at a time .


Electric Testing Techniques You Need to Know
Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts

May 07, 2017 | Ford Cars & Trucks

1 Answer

Right blinker not working 1999 Buick park avenue


You'll need to find a wiring diagram an component location chart to check this out . Here is a diagnostic flow chart for trouble shooting this problem ! Do you know how to use a voltmeter ?
DEFINITION: This table diagnoses inoperative turn signals on one side. It assumes that the cornering lamps, hazard lamps, and turn signals on the other side all operate properly.

1

Did you perform the Exterior Lights System Check?
--
Go to Step 2 - yes
Go to Exterior Lights System Check - no

2

  1. Disconnect the turn signal flasher connector.
  2. Turn the ignition switch to the RUN position.
  3. Place the turn signal switch in the appropriate position.
  4. Connect a DMM from the appropriate turn signal flasher connector cavity to ground:
?€¢
LH: cavity C (ORN)


?€¢
RH: cavity B (BLK)

Is the voltage within the specified range?
10-15 V
Go to Step 3 yes
Go to Step 5 no

3

Connect a fused jumper between the appropriate turn signal flasher connector cavities:
?€¢
LH: cavity C (ORN) to cavity D (YEL)


?€¢
RH: cavity B (BLK) to cavity F (TAN)

Do the appropriate turn lamps light without flashing?
--
Go to Step 4 yes
Go to Step 6 no

4

Replace the turn signal flasher. Refer to Hazard and Turn Signal Flasher Replacement .
Is the repair complete?
--
Go to Exterior Lights System Check
--

5

Repair the open in the appropriate circuit:
?€¢
LH: CKT 57 (ORN) between S200 and the turn signal flasher


?€¢
RH: CKT 58 (BLK) between S201 and the turn signal flasher

Refer to Wiring Repairs in Wiring Systems.
Is the repair complete?
--
Go to Exterior Lights System Check
--

6

Repair the open in the appropriate circuit between the turn signal flasher and the IP fuse block:
?€¢
LH: CKT 685 (YEL)


?€¢
RH: CKT 686 (TAN)

Refer to Wiring Repairs in Wiring Systems.
Is the repair complete?
--
Go to Exterior Lights System Check

May 09, 2015 | 1999 Buick Park Avenue Ultra

1 Answer

Rh brake light will not work. Bulbs is good and center and left light work..Brake switch ???


Definitely not a brake-light switch. Providing that the bulb is good, it seems that you have a bad socket or wiring on the right side. Does the RF signal come on? If it does that eliminates the turn signal switch.

Jul 01, 2011 | 2003 Dodge Caravan

1 Answer

I have a 2003 2 door explorer sport, just recently my turning signal and break light have stopped working on the passenger side!! I changed the light bulb, and nothing!! I changed the turning signal light...


No, because the left side is still working. The loose wiring was to the multifunction switch (turn signal).

Power gores through the turn signal switch to the brake switch on the brake pedal, then to the rear lights. Does the highmount brake lamp work?
At the RH lamp socket, Measure the voltage between the RH rear lamp C4032 pin 3, circuit 5 (OG/LB), harness side and ground. Should be 12 volts.

try that first.

Did you change the front and rear bulbs?

May 21, 2011 | Ford Explorer Sport Cars & Trucks

1 Answer

RH turn signal flashs" quickly.


obviously you have no feed to this lamp ,check the connector plug and follow the loom back in case it has a dirty connector ,could evan be the hazard switch

Nov 25, 2009 | 2000 Audi A8

1 Answer

Center brake light illuminates, but LH/RH brake lights do not


LH/RH lights cable could be disconnected anywhere, will take a long time to trace.
Center Brake Light and LH & RH should be connected at one point.
Jump a cable from Center Brake Light to one of Rear Break Light.
Hope this will works.

Sep 12, 2009 | 1995 Toyota Tercel

1 Answer

1992 Dodge Dakota LH tailight problem


Have you taken bulb out & cleaned terminals inside socket & either cleaned bulb base & terminals, or tried replacing bulb?

Mar 10, 2009 | 1992 Dodge Dakota

2 Answers

2003 denali trailer wiring


If your signals & brakes are on 2 different circuits, ( for example a red lens for stop & an Amber for turn.) then you'll need to buy a converter that goes between vehicle & trailer. They're not too expensive at any trailer or RV place. I think some of the autoparts stores stock them now too.

Jun 20, 2008 | 2004 GMC Sierra Denali

Not finding what you are looking for?
1994 Dodge Dakota Club Cab Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...