Question about 1999 Chevrolet Monte Carlo

1 Answer

Car Stalls after at its own will with the P0102 Code

The car stalls at its own will, occasionally the SES light comes on and will spit out the P0102 MAF Sensor Low Input Code. Should I clean it or just replace it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 753 Answers

While the engine is running try tapping the mAF sensor with a wooden handle to see if that causes the engine to stumble or shut-off if it doesn't I would just clean it to see if that would solve your problem. You should also check and clean your throttle plate and throottle bore any carbon build up around the edges blocks off Idle air and can cause a stall condition.

Posted on Sep 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check Engine Light P0740. Car stalls when starting (occasionally), and the transmission slips when stopped.


This code is set when the transmission control module detects improper voltage at the torque converter clutch. This can be caused by low tranny fluid/dirty tranny fluid/defective torque converter clutch solenoid/electrical connections to from solenoid

Nov 09, 2015 | 2001 Infiniti QX4

1 Answer

Overheating


check engine lamp (CEL, SES or MIL)???????
why not scan it.?????? any 19$ scan tool works.
stalls,
1: can stall be saved with a fast right foot (key evidence!!!)

Dec 18, 2013 | 2001 Suzuki Swift

1 Answer

Error codes P0507 and P0102 after replacing MAF sensor


P0102: you need to make sure the sensor is clean; sometimes it get dirty as you are working on an old car. Check the voltage manually. Make sure there is no air leak near it

P0507: high idle... this sounds like a vacuum leak. get starter fluid and start the car. Spray around and check for change in car idle

Dec 09, 2013 | 1998 Pontiac Grand Prix

1 Answer

Kia rio 2003 scanned & found p0102 faults are stalls immediately after starting, inability to acclerate, misfire


p0102=Mass or Volume Air Flow Circuit Low Input
p0300=Random/Multiple Cylinder Misfire Detected

sounds like its out of time

Sep 25, 2012 | 2003 Kia Rio

1 Answer

Why is my Grand Prix surging/stalling when ideling?


If you did not disconnect the battery and drain the voltage from the ECM, it could be using old settings when the problem existed.
When a problem occurs, the computer tries to correct it or find new settings to work around the problem. When you fix a problem you have to clear the codes and sometimes erase the memory from the computer to allow it to start back at the factory settings.
When you disconnect something and the check engine light comes on, the computer goes into limp mode and uses values for the sensors preset by the factory. The car will almost always run rich to ensure the driver can get back to a place for repairs.

Aug 23, 2012 | 2000 Pontiac Grand Prix

1 Answer

Car stalls unless gas constantly supplied otherwise car dies all dash lights come on usually on start up


Inspect and clean IAC valve (idle air control valve), replace if necessary. If IAC is Ok, please provide additional info!! Does your vehicle experience random or repeated hard starts?? Is your "service engine soon" light on?? These vehicles are known for faulty crank position sensor, usual symptoms are: hard starts, random/constant stalls, SES light on, misfire or no start. Some or all symptoms may or may not occur simultaneously.

Oct 11, 2010 | 2000 Oldsmobile Intrigue

1 Answer

Car keeps stalling


your request has to many possibilities.which motor,is it in park,do you hear a whistling noise.

Apr 27, 2009 | 1994 Chevrolet Beretta

Not finding what you are looking for?
1999 Chevrolet Monte Carlo Logo

Related Topics:

395 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...