Question about 1999 Hyundai Accent

1 Answer

Engine light will not go out and then starts flashing

Posted by on

  • carhob May 11, 2010

    have cars ecm scanned for trouble codes!

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 382 Answers

Dear friend-you can try to reset the ECU by disconnecting the battery for a short while and reconnect,if light still comes on then connect to a scanner to reads the codes.

Posted on Sep 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Check engine light flashing check engine soon smell of gas and not running smouth


Check engine light flashing means there is a bad misfire , it flashes to tell you your damaging your catalytic converter . You need to have it check , you don't won't to have to replace the catalytic converter . Can cost up to $1,000.00 . Flashing Check Engine Light CarMD

Feb 03, 2016 | 2004 Cadillac Deville

1 Answer

My Holden barina won't start and check engine light is flashing


Check Engine Light On - Auto Diagnosis Repair Help

www.aa1car.com/library/mil.htm
The Check Engine Light (which is actually the Malfunction Indicator Lamp or ... you can assume the fault that is causing the Check Engine Light to come on is probably minor and won't hinder your ability to continue driving. ... When the ignition is turned on (don't start the engine yet), the tool will .... flashing check engine light ...

What Causes the Check Engine Light to Come on in a Car?

www.wisegeek.com/what-causes-the-check-engine-light-to-come-on-in-a...
Nov 7, 2015 - When the check engine light comes on, take the car to a reputable mechanic .... I went to go home. the check engine light was blinking and it won't start. ... I looked in my manual book for 2001 holden barina car to see what the ...

Car cranks but won't start, Check Engine light blinking ...

www.evolutionm.net/...engine.../424408-car-cranks-but-won-t-start-chec...
Jun 1, 2009 - I tried to turn it back on but it would only crank and not start, the check engine light is also being really weird, it's blinking on and off pretty quick.Missing: barina

Check engine light flashing car won't start - RX8Club.com


Dec 09, 2015 | Holden Cars & Trucks

1 Answer

Where is the obd2 connector location on holden ra rodeo v6


isuzimpuls.gif
Connect white (test lead) and black (ground lead) wires that are branched from harness approximately eight inches from ECM. After leads are grounded, the "Check Engine" light will flash the diagnostic trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.I-MARK 84-85
Connect male and female test leads taped into wire harness near ECM. After leads are connected, the "Check Engine" lamp will flash the trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.
86-87 Impulse located near the ECM connector, is used to actuate the Engine Control Module (ECM) trouble code memory within the module. Two terminals (A and C) of this connector are used to activate the diagnostic trouble code system in the ECM. With the ignition switch turned On, engine Off, connect a jumper wire between terminals A and C. The "Check Engine" lamp will begin by flashing a DTC 12. DTC 12 = flash, pause, flash, flash. There will be a longer pause and a code 12 will repeat two more times. This code indicates the self-diagnostic system is operating. The cycle will then repeat until the engine is started or the ignition is switched Off. In most cases, DTC's will be checked with the engine running since no DTC's other than DTC 12 or 51 will be present without the engine running. Remove jumper wire from ALDL connector before starting engine. Reconnect jumper wire after engine is running.

Throttle Body Fuel Injection

The ECM test connection is located under the center console.
A built-in, self diagnostic system will identify problems in the throttle body fuel injection system. When a problem is detected, the diagnostic system will illuminate the "Check Engine" light.
When the engine is started, the Check Engine light should turn off.. If the light remains lit, the self diagnostic has detected a problem. To determine where the problem exists, ground the "Test" terminal of the connector with the ignition On, engine Off and watch the check engine light. Each DTC will flash three times (lowest to highest).

Aug 21, 2014 | Holden Rodeo Cars & Trucks

1 Answer

When i unlock the door the lights start flashing and the engine wont start after about 60 seconds the lights quit flashing but the engine still wont start95 nissan maxima


Sounds like the anti-theft system has been activated. The horn would normally blow in conjunction with the flashing lights.

Feb 19, 2014 | 1995 Nissan Maxima

1 Answer

98 jeep cherokee sport flashing engine light


The check engine light is because all check engine light codes are caused by components that affect emissions. It's not actually an engine problem, it's a problem with either your O2 sensor, MAF sensor, fuel/air ratio, pyrometer, or exhaust.
______________
gm diagnostic tools

Nov 22, 2012 | 1995 Jeep Grand Cherokee

1 Answer

Check engine light flashing in 2006 chevy hhr


If it is running rough & no check engine light on then the first thing I would to is tune it up. If you have a check engine light then pay someone to diagnosis it & go from there. Usually when the light comes on there is a more promenient issue; that is WHY the light continues to flash.

Oct 01, 2012 | 2006 Chevrolet HHR

1 Answer

1998 terrano immobiliser fault wont start


hi, i have nissan terrano wen i switched on engine light flash and start engine its start then go of.nissan terrano patrol engine

Sep 06, 2012 | Nissan Sentra Cars & Trucks

1 Answer

Engine light on 1988 dodge caravan


Cycle key to on (not start) then off, then on, then off, then back on & leave in on position. Now watch check engine light and it will begin to flash. When it does, it will flash a certain number of times, then pause, then flash some more. Count those flashes and write them down. All numbers will be 2 digits. For example: flash,flash,flash, pause, flash ,flash,flash. will be code 33. Then small pause starts next set of numbers. When you get 5 flashes, pause, 5 more flashes, =55, that means end of message/codes. Do that a couple of times until your sure of the number(s) and get back to me/us and we will be able to help better from the codes.Saves time and money.

Mar 09, 2012 | Dodge Cars & Trucks

1 Answer

Engine light flashing


in a dark area/at night, take a spray bottle w/water and mist the engine all around the cap,coil,wires. watch for arching,flashing.

Oct 17, 2008 | 1997 Mazda Protege

Not finding what you are looking for?
1999 Hyundai Accent Logo

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...