Question about 2001 Jeep Grand Cherokee

1 Answer

Inside the drvers door there a piece that holds the bar that opens the door what is that part called

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 546 Answers

I'm not sure that I've got the picture,but let me guess you need a DOOR HANDLE TO LATCH LINK,[just like the one laying in the bottom of the door?]

Posted on Sep 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the door handle


take off the inside door panel and look for the screws or nuts that hold the handle in place and take them out. then you onhook the metal bars from the handle. you have to pop the bar out by turning the plastic piece and then pull it out of the holder

May 23, 2011 | 1999 Chevrolet Silverado 1500

3 Answers

Locked the key inside. how can i unlock the door?


You can use a pry bar or a very large screw driver( 14+inches).put a piece of card board on the prying tip to protect the paint.Pry the top right corner tip of the driverside door enough to slip a 2 1/2 foot wire coat hanger through the opening hitting the door unlock switch.You may have to repeat a couple times bending the hangar to suit your aim.The door is flexable so you wont break it.

Oct 03, 2009 | 1998 Chevrolet Blazer

1 Answer

The latch that opens the Trunk (Hatchback - as it is a minivan) is broken. I cannot open the back...


If you still have the broken piece, you can try to use that to try to open the back. Otherwise, you have to open it from the inside.
I changes mine in 2007 so if memory serves me, I had to remove the back panel and pull on the cable to open the door.

Now to see and pull on the cable, and replace the latch, you have to take off the inside liner/panel to get to the latch to replace it. This took about 2 careful hours to replace.

The trick is to get the two side pieces off.
These two plastic pieces are next to the window on the left and right sides. Each piece is about 3 inches wide and 18 inches long. Using a strong grip, or a pry bar or large screwdriver, take off both pieces. There are three clip areas that holds each piece in.

If you are using a tool, be careful to protect the area by wrapping a towel on the screwdriver/tool.

After that the bottom liner piece pulls away and you can see the latch.
There are two screws/bolts that holds the latch.

The two pieces snaps back in pretty easily.

You probably broke the plastic piece shaped like a J.
You can try to glue the pieces back, but note that the piece broke due to age. I changed the whole assembly - good for another 7 yrs. I could not find just the plastic piece.








Aug 29, 2009 | 1999 Toyota Sienna

1 Answer

I cannot open my trunk cannot grip handle its just hanging is there a safety latch to open it or a string or something will not open with key will not open with power lock either because I cannot press...


I posted this for a manual door - not sure for automatic door.

If you still have the broken piece, you can try to use that to try to open the back. Otherwise, you have to open it from the inside.
I changes mine in 2007 so if memory serves me, I had to remove the back panel and pull on the cable to open the door.

Now to see and pull on the cable, and replace the latch, you have to take off the inside liner/panel to get to the latch to replace it. This took about 2 careful hours to replace.

The trick is to get the two side pieces off.
These two plastic pieces are next to the window on the left and right sides. Each piece is about 3 inches wide and 18 inches long. Using a strong grip, or a pry bar or large screwdriver, take off both pieces. There are three clip areas that holds each piece in.

If you are using a tool, be careful to protect the area by wrapping a towel on the screwdriver/tool.

After that the bottom liner piece pulls away and you can see the latch.
There are two screws/bolts that holds the latch.

The two pieces snaps back in pretty easily.

You probably broke the plastic piece shaped like a J.
You can try to glue the pieces back, but note that the piece broke due to age. I changed the whole assembly - good for another 7 yrs. I could not find just the plastic piece

Aug 14, 2009 | 1998 Toyota Sienna

3 Answers

2000 blazer door


The part in the door is called the Door Latch/Electric lock assembly,(If you don't have electric locks it's just called the door latch), The part in the door jam is called the striker assembly.

Jun 05, 2009 | 2000 Chevrolet Blazer

1 Answer

My 1999 Toyota Sienna has a broken rear latch


I answered this for someone else -

If you still have the broken piece, you can try to use that to try to open the back. Otherwise, you have to open it from the inside.
I changed mine in 2007 so if memory serves me, I had to remove the back panel and pull on the cable to open the door.

Now to see and pull on the cable, and replace the latch, you have to take off the inside liner/panel to get to the latch to replace it. This took about 2 careful hours to replace.

The trick is to get the two side pieces off.
These two plastic pieces are next to the window on the left and right sides. Each piece is about 3 inches wide and 18 inches long. Using a strong grip, or a pry bar or large screwdriver, take off both pieces. There are three clip areas that holds each piece in.

If you are using a tool, be careful to protect the area by wrapping a towel on the screwdriver/tool.

After that the bottom liner piece pulls away and you can see the latch.
There are two screws/bolts that holds the latch.

The two pieces snaps back in pretty easily.

You probably broke the plastic piece shaped like a J.
You can try to glue the pieces back, but note that the piece broke due to age. I changed the whole assembly - good for another 7 yrs. I could not find just the plastic piece

Apr 13, 2009 | 1999 Toyota Sienna

1 Answer

Exterior rear door handle on Honda Accord 2001


To Remove Door Panel on 2001 Honda Accord:

A: To remove the plastic piece with the door lock button and door handle connected to it:

1- Remove the screw in the middle located behind a plastic cover button
2- Push (slide) the whole assembly Forward (toward front of car)
Besides the screw, it is held in place by 3 hooks on the backside that hook into holes in the metal door frame
3- Now unhook handle from small metal bar going through door by pushing (toward door) plastic clip (blue?) off of the bar, then the bar will come out of the clip hole, thus releasing the handle.
4- Depress little grey button /bar (purple painted on it)on elec. connector to seperate connector, thus releasing door lock switch

Now the whole assembly (metal handle, door lock switch, and plastic piece) will come off door panel

B: The door is held on by 2-screws, 7-plastic snaps/plugs, and 1-plastic plug.

The screws are located: bottom of hand hold and the other behind the handle, both covered by little covers that have to be pryed off to access the screws.(hint: the screw with the built in spacer goes behind the handle when you are trying to reinstall)
The 7-plastic snaps: 3 across bottom and 2 on each side. Not visible, they are mounted to the inside of the panel.
The 1-plastic plug is visible at the upper front of the panel and is the same color as the surrounding trim


C: Take off the big plastic triangle piece above the door panel and behind the mirror. Pull/pry off. It has 2 snaps holding it on. one near bottom and one near the front.

D: Light lens prys off from bottom. Unscrew (1/4 turn) the light assembly with bulb still intact from backside of panel

E: Remove the Hand-Hold/window switch assembly:

Jan 14, 2009 | 1997 Toyota Camry

1 Answer

Ford 1.8tdi hatch


This is going to be a pain in the backside. You need somewhere dry to work. You will need to pull off the inside door panels, and you may damage them in the process. This is probably down to lack of long term mainenance and lubrication in the lock mechanism, and now its either too worn, or the pushrods have bent. If you remove the inside panels, and the plastic sheet liner, you may be able to push the rods about enough to open the door. You will then need to remove the lock mechanism and clean, grease and possibly straighten the rods before reassembling. Check with door open and using a screwdriver to simulate closing the door.

Jan 12, 2009 | 1996 Ford Escort 4 Door

1 Answer

98 Jeep Wrangler door handle won't open door


there is a metal bar inside that clips into the handle they come off all the time there is a plastic clip that hold the 2 together it most likely has fallen off and into the bottom of the door you can put it back together easily if clip cannot be found you can buy them at local parts store for a couple bucks..hope this helps

Nov 21, 2008 | 1998 Jeep Wrangler

2 Answers

Drivers door does not open


Do you have triple A membership? if you have or your friend has it, you can call the triple A to open the door for you, it will cost you nothing.

Because there is a plastic clamp hold the bar connected to the door opener was broken or loss.

If you don’t have AAA membership, if you do not want to call Lock Smith, you can make a flat metal tool, just like one foot stake measurement , it should be around 18” and cut the front part like a C hook , shot from outside window near the handle, try several times see if you can hook the open bar from inside the panel, if you touch the inside handle bar, just pull it up, the door will open.

Jun 25, 2008 | 1995 Toyota Camry

Not finding what you are looking for?
2001 Jeep Grand Cherokee Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...