Question about 1998 Chevrolet C3500

Open Question

Ihave a 1998 pace arrow vision motorhome with a 454 vortex chevy motor. I have trouble with it not starting when you turn the key but if you hold it on start some times it will take 30 or more seconds to crank over.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 32 Answers

SOURCE: Need timing marks for 93 chevy 454

Under the hood on the emissions decal should say what degre the timing should be set at. ther is a one wire plug that is brown with a black stripe u need to un plug befor seting the timing with a timing light . u can usually find that under the glove box or behind wher the fuel pump relay is . i think the timing is set at 4 degres on the timing pointer but look for the decal first too make sure im right.

Posted on Feb 19, 2009

Ad
  • 1 Answer

SOURCE: Where is the ignition module on a 1990 Ford 460 engine

its either on the left frt fender apron or mounted on the distributor

Posted on Apr 05, 2009

joecoolvette
  • 5660 Answers

SOURCE: 1998 454 engine wont start. starter replace selonoid replaced.

Items of interest.

1.When a starter fails to start a vehicle, and the wiring has been found to be bad, and changed, one suspects the wiring first.

2.If a starter is suspected to be bad, one takes it out, and performs a benchtest, or takes it to an auto parts store, and see if they can do a benchtest. They need to load test it, not just see if it will Spin!

This test result should stop the needless buying, of starter after starter. If you get three bad starters in a row from an auto parts store, I suggest it's time to change auto parts stores! (Make sure, you are not twisting the S terminal on the Solenoid, when installing the ignition wires)

3.The frame of your vehicle should be the Ground.

Make sure that the motor home manufacturer, hasn't reversed the system for this motor home, and is using the frame for Positive.
This was done in the past for some older vehicles, because it was thought to reduce rusting, of the frame. However, you're dealing with a motor home. Hard to say what type of system they used.
Normal, would be using the frame as a Ground.

In the normal type of setup, of using the frame as ground, make sure where the starter contacts that 454 Chevy engine block, that this area of the starter has no paint on it. The starter grounds through the engine block, and where the starter contacts the engine block.

Make sure also, that this area of the engine block has no paint on it.

Be sure that there are flat braided ground straps going from the frame, to the engine block. If they are an insulated wire, and not braided flat straps, be sure they are about the thickness of your little finger. You'll notice I stated -> They. There should be TWO of them. ONE, will NOT Do!

The frame is the ground. The starter gets it's Ground source from the engine. The engine gets it's ground source from the frame. The only contact the engine has to the frame, is the motor mounts, and the transmission mount. They have
RUBBER in the middle!
There HAS to be -> ground straps! There MUST be TWO of them for the correct amount of grounding!

4.Power to start the starter turning comes from the ignition switch. The reason you have a solenoid on the starter, is so that there won't be a wire that is the thickness of your little finger, going up to the ignition switch!

Check the wire that comes from the ignition switch, for power, once the ignition switch is turned to the Start position.

Battery -> Negative terminal disconnected. Ignition wire from starter disconnected. Put electrical tape on the terminal end, of the ignition wire you removed from the starter solenoid. (Goes to the -> S <- on the solenoid)

Leave the other wires on, put the nut back on, and tighten. (Use caution in this area. The nut is only 5/16 inch, or 11/32. This means that threaded post is TINY. DON'T overtighten! IF, the threaded post starts to turn, STOP! Pull out on the post.

Inside the solenoid cap, that you can't see, there is a square boss, on inside end, of this tiny threaded terminal post. The solenoid cap, has a square hole that this boss fits into. Keeps that tiny threaded post from turning. Inside the cap, the tiny threaded post is connected to a one strand copper wire. If you twist the tiny threaded post, more than 90 degrees, the wire will twist off! Time for another solenoid!

Wheels chocked. Transmission in neutral, and it's best to have the parking brake on, and someone in the drivers seat. Have this person hold their foot down on the brake pedal. This way you avoid any accidents happening to YOU, someone else, or property.

Reconnect the Negative battery terminal. (Order of connecting up a battery is ALWAYS, Positive terminal First, Negative terminal last)

Take a multimeter set it to DC, and to the 50 volt scale. Find a clean, non-painted surface on the frame, (Or scratch a little area), touch the Black lead, (Negative probe) of the multimeter to it. Touch the Red lead, (Positive probe), of the multimeter to the ignition wire, electrical tape partially removed. (Enough so you can make a good contact to that terminal. The tape is there, in case the wire slips out of your hand, and touches a ground. If it has no tape, you'll think it's the Fourth of July under there!)

No reading? Be sure the person inside, has the ignition switch in the starting position. Still no reading? Check that ignition switch out. See if it's getting power.

Posted on Apr 24, 2009

  • 316 Answers

SOURCE: How can I tell if I threw a rod on my chev 454 RV engine ?

You can remove your valve covers to inspect the rocker arms, and push rods. They should be all in place and not too loose. If you find nothing out of place on the top side of the engine, you will have to look to the lower end. From there, you may have to remove the engine to inspect the rods; I doubt you can remove the oil pan while the engine is in the vehicle.

Posted on Jun 03, 2009

ourhowse
  • 2007 Answers

SOURCE: 1998 Chevy Blazer won't start (intermitently)

You will have to find out if it is lacking gas, spark or air first. And here's a tip: Never use ether on a gas engine. That could be the reason it's not starting now. You might be lacking gaskets or valves. Ether... starting fluid is for use on diesel engines only. If you don't know what you're doing on a diesel, you can do more harm than good, and not omnly can you blow your gaskets out, you can blow your head off trying.

Posted on Jun 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT KIND OF TRANSMISSION IS IN MY RV? IT HAS A CHEVY 454 ENGINE.


454 chevy engine in motorhome - RV-Coach Online

www.rv-coach.com > Discussion Forum > Mechanic's Corner - Engines
Mar 25, 2010 - I have a 1995 winnebago elanden Chevy chasis and Chevy 454 motor.... I am trying to tighten or replace all the belt on my 1987 Fleetwood Southwind ... What type trans fluid,oil and filter does the 1984 chevy rockwood motorhome take? .... Havereplace ignition switch, check neutral safety switch at transmission, all OK. RV with Chevy 454 engine problems
Oct 18, 2015
454 P30 radiator removal
Jul 23, 2012
Overdrive Transmission Conversion
Nov 6, 2010
4L80E Transmission Problems
Nov 15, 2009
More results from www.rv-coach.com

Nov 24, 2015 | Cars & Trucks

1 Answer

Carburetor removal 454 chv engine how to 1982


Carefully mark a the vacuum hoses and take picture

Mar 27, 2014 | 2001 Daewoo Lanos

3 Answers

I need to find starter for 1988 fleetwood pace arrow, not turning over when itry to start it.


Bottom of the engine at the rear or block pointing into the transmission bell housing

Sep 30, 2012 | Cars & Trucks

1 Answer

Detailed wiring diagram required for 1993 Pace Arrow RV.


I just recently purchased a 1993 Pace Arrow and I believe I may have all paperwork on the 454 engine but its a gas engine. Not sure if it helps but I also remember seeing a chevy chasis book in the package.

Nov 30, 2011 | Cars & Trucks

1 Answer

I am trying to locate the p\oil pressure sender on


That location is correct but gm also put them underneath the engine just forward and up from the oil filter.....

Dec 08, 2009 | 1991 Chevrolet K2500

2 Answers

Need an owners manual for 84 southwind motorhome 454 chevy


hi, have a look on this site, maybe find what your looking for.....good luck

Aug 19, 2009 | 1984 Chevrolet Sportvan

Not finding what you are looking for?
1998 Chevrolet C3500 Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...