Question about 1999 Ford Expedition

1 Answer

Which fuse do I pull to reset the OBD codes on a 1999 Ford Expedition 5.4L?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 708 Answers

Dont pull anyfuses. Unhook the battery for about 30 minutes. IF there is a problem with it you havent addressed the computer will light it up again once it retrains itself.

Posted on Sep 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Smog test not ready on OBD II results


You can get an obd reader that resets codes, pull the fuse marked ecm or pcm and wait or unhook the battery.

Jul 08, 2016 | Cars & Trucks

1 Answer

Whats ford windstar error codes p0715 mean


I hope this helps and is what your looking for... good luck

http://www.fordobdcode.com/p0715-ford

Ford P0715 OBD-II Trouble Code Definition:
P0715 Input Shaft Speed Sensor Circuit Malfunction
P0715 Ford OBD-II Trouble CodeDescription:
OBD Trouble Code P0715 Input/Turbine Speed Sensor "A" Circuit What does the code mean? OBD-ii Code P0715 definition:
The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM). Symptoms Sumptoms of OBD code P0715
- Engine Light ON (or Service Engine Soon Warning Light) - Possible shifting problems Causes Causes of the OBD-II code P0715
- Transmission speed sensor circuit is open or shorted. - Poor transmission speed sensor circuit connection - Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor. Solutions

Jun 22, 2014 | 1999 Ford Windstar

1 Answer

Batt,was out 99 taurus obd want read


Try disconnecting the battery for 10 minutes or go to Schucks to have them reset the MIL and clear codes.

Apr 05, 2013 | 1999 Ford Taurus

1 Answer

On-Board Diagnostic II (OBD II) Diagnostic Link Connector (DLC) Location in 1999 ford Ranger


the ecc diagnostic plug is what ford used b 4 going to the obd 2 system check with ur local ford dealer for checking codes

Jan 08, 2013 | Cars & Trucks

1 Answer

2000 Ford F250 Supercab-Engine light comes on even after you reset it. No code shows up when you scan it.


If it is a diesel engine then unfortunatley they are NOT OBD II compliant. They do have the OBD II port but the scanners you can use at the A/P store won't pull those code(s). You will have to use a scanner that pulls PSD code(s) or go to a shop with the equipment or the dealer.

Jan 28, 2011 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

What fuse # controls the obd on a 1999 Ford Ranger


fuse #5 mini. located at fuse box, orange wire and connected to obd connector pin # 16 (hot at all times)

Aug 05, 2010 | Ford Ranger Cars & Trucks

1 Answer

1999 ford ranger 2.5 obd 11 code reader has no power (no response) when plugged in, works in other vehicles, did work 2 wks ago


first check batteries in the reader an dmake sure all the connections leading into the port are good. now find the fuse boxes and check your fuses. if that dosent fix it you will need a multiemeter to test the wiring. Good luck and happyhunting

Aug 20, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Egr code still present after changing solinoid and checking valve


Have you had the code reset using an OBD 1 scan tool? It must be reset as the code remains in the computer.

May 03, 2009 | 1999 Ford Taurus

1 Answer

1999 ford windstar check engine light


had the same problem with my 1999 Windstar. The part's store told me that it's on the same fuse as the ignition switch. So I ruled out a fuse issue because everything else on my ignition was working just fine. They suggested I run a new hot wire to the connector. That didn't sound right to me. A couple of weeks later my alternator went. After I replaced it, the OBD II now reads just fine.

Nov 09, 2008 | 1999 Ford Windstar

Not finding what you are looking for?
1999 Ford Expedition Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...