Question about 2002 Land Rover Freelander

Open Question

What are the torque settings for the cylider head gasket on a 1.8 landrover freelander 1999.thanks.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
the terrier
  • 94 Answers

SOURCE: head bolts torque settings

according to the manual its 22NM or 16lb/ft

Posted on Oct 26, 2008

Ad
  • 15 Answers

SOURCE: replacement of cylinder head gasket freelander 1800 petrol

DEFINITELY NEW BOLTS.
1ST STAGE 20 NM
2ND STAGE 180 DEGREES
3RD STAGE 180 DEGREES.....JOB DONE.

Posted on Jul 06, 2009

  • 1 Answer

SOURCE: what is the marking for the timing belt setting for freelander landrover 2002

timing info on a 2002 landrover freelander v-6

Posted on Aug 28, 2009

  • 75 Answers

SOURCE: TORQUE SPECS /HEAD GASKET/2001 CAVALIER...

for the 2.2L OHV:
(pully 8 4 1 5 9 <-- long bolts @ 63Nm (46ft/lb)
side ) 7 3 2 6 10 <-- short bolts / 10 is the stud @ 58Nm (43ft/lb)

for the 2.4l dohc are as follows:
(pully 9 3 1 5 7
side) 10 6 2 4 8
bolts 1-8 torqued to 65Nm (40ft/lb)
bolts 9-10 torqued to 40Nm (30ft/lb)

then (either engine) give each an additional 90° (¼) turn

it's best to do the tightening in stages, you don't want to go completely tight on the first pass or there will problems and you'll get to do it all over again

Posted on May 24, 2010

  • 2926 Answers

SOURCE: cylider head torque specs ford windstar 1996 3,8

Position the cylinder head on the cylinder block. Tighten the cylinder head bolts in 2 steps following the proper torque sequence. The first step is 37 ft. lbs. (50 Nm) and the second step is 68 ft. lbs. (92 Nm).


98c7056.gif

Posted on Oct 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder head bolt torque settings 1998 landrover freelander 2.0 t diesel


go to www.automecanico.com and get the specification. Translate this amazing website with your browser and fix it.
God bless you

Jul 12, 2013 | Cars & Trucks

1 Answer

Im having to change my head gasket, whats the torque spec and sequence on a 96 landrover discovery? im changing both head gaskets. anything i should know?


start in middle and work outwards alternately ,bolt torque 80lbs and pull down if three passes ,speed key --rachet- torque wrench .although iam posting this i never use a torque wrench i go by the feel of the bolt stretching ,make sure heads have been checked and skimmed before refitting

Aug 10, 2010 | 1997 Land Rover Discovery

2 Answers

Oil is mixing with antifreeze. landrover freelander . 1.8 petrol. year 2000


Sorry to be the one to tell you but you have a major expense on your hands. It is either a blown head gasket (the cheapest solution) or a cracked head (the next most expensive solution) or a cracked block (don't ask! ). Take it to a shop and have them do a compression test to find out which cylinder is leaking. Then get at least three quotes on repairing the damage. Good luck!!

Apr 19, 2010 | 2002 Land Rover Freelander

2 Answers

Blown Headgasket


without mechanical knowledge, best left to a garage. if you have a bit of knowhow then do an assessment of what is connected to the head, inclusive of exhaust manifold and fuel inlet manifold, wiring etc.Once you decide how to do it, note where all bolts and wires go.Clean every bit of old gasket off all faces and as the head is alloy get a head skim from a motor factor or machine company. You will need a new set of cylider head bolts and full head gasket set. Torque settings , however will need to be obtained along with the head bolt sequence for retightening

Aug 07, 2009 | Saab 9 5 Cars & Trucks

Not finding what you are looking for?
2002 Land Rover Freelander Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...