Question about 1988 Mazda B2200

1 Answer

1990 mazda b2200 fuel injection after about 30 min engine stops and in 20 min starts up ok until another 30 min and stops again spark is ok and fuel pressure seems ok ,engine will crank but seems like its totaly dead then I wait a 15 to 20 min and it runs like brand new.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 347 Answers

Check fuel filter and fuel pump. replace if not functioning.

Posted on Oct 03, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

Start and idle for an hour but after turning of for 30 mins will not restart until the next day

You may be getting a vapour lock in your fuel system. Disconnect fuel pipe from filter and check fuel flow. Take the car to a mechanic???

Oct 09, 2014 | 2000 Ford Expedition

1 Answer

1990 mazda b2200 2.2l fuel injected won't accelerate just bogs down idles fine

I think you have established that it is getting fuel but I guess what I would do is check into the throttle body itself.

May 20, 2014 | 1988 Mazda B2200

1 Answer

Mazda MPV 2.6 1989 good ecm, good injectors (but no voltage), good spark, good fuel pressure, engine cranking, but won't start. If I put a little bit of gas on the air intake it will start. there's no...

You probably have a bad ecm. These engines used the same ecm that the injected b2200 used and they had a lot of problems with capacitors that leaked and damaged the etching on the ecm's circuit board. If you do indeed have 12V on one side of the injectors and no pulsing ground from the ecm, then the problem either in the ecm or the wiring between the ecm and the injectors. When you say good ecm, have you tried a known good one?
If you're really good at desoldering and repairing pc boards, you can fix it yourself, all you'll need is a 47uF capacitor. Or you can send it out.

Jan 11, 2011 | 1989 Mazda MPV

1 Answer

When im driving my truck,it starts to sputter and

I would try spark plugs and wires. If it was a fuel line you would see the leak or atleast smell it very strongly. If the problem still exists after new plugs and wires try the distributor cap.

Apr 21, 2010 | 1988 Mazda B2200

2 Answers

How do i reset check engine light on a 1989 mazda b2200

Disconnected the battery for 30mins and then connected again.

Mar 11, 2010 | 1988 Mazda B2200

1 Answer

1990 Mazda B2200 w EFI- Starts and dies

When you turn the key to the on position can you hear the fuel pump turn on? If not, the fuel pump relay has gone bad. Make sure you have at least 5 gallons of fuel in the tank. Check and make sure you have fuel flow to the rail, try cracking the banjo bolt on the fuel rail.

Jan 24, 2010 | 1990 Mazda B-Series

1 Answer

1990 mazda b2200 starts & idle but dies if I push on the gas.

You need to run a pressure check on the fuel line with the appropriate gauge.

Mar 07, 2009 | 1988 Mazda B2200

1 Answer

1989 Mazda b2200 starts but won't stay running

My mazda b2200 starts and will stay running as long as the key is in the start position, but stops as soon as the key is turned from the start position

Feb 07, 2009 | 1989 Mazda 323

1 Answer


Try checking your Spark plugs (they MUST be the right type, clean, and properly adjusted: and try adjusting your timing. Either or both of these could cause this type of problem Hope it helps. If so, don't forget to rate the answer, will you?

Dec 13, 2008 | 1988 Mazda B2200

2 Answers

1990 mazda b2200

i just bought an 88 that crazy overheated could only drive for 30 mins before had to stop. no leaks anywhere, did a compression check on the cylinders,checked out. no water in oil. took the radiator to a shop theyll do a flow test for free, got mine fixed for like 80 bux but you can buy a new one for 120. the white smoke might be your fuel filter

Jul 31, 2008 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

430 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides