Question about 2004 Jeep Liberty

2 Answers

Idles high went you stop - 2004 Jeep Liberty

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 2,359 Answers

Low / uneven idle problem can cause by a lot of components.

Dirty air filter

Dirty injectors + o-rings

Vacuum leak at intake manifold and vacuum hose.

Bad Idle Air Control Motor (IAC)

Low compression (170 psi + is OK)

Start cleaning and repair these trouble spots and see is there any improvement.

====

For more advance DIY'er then you may try this.

Use a can of Berryman carburetor clean to locate the vacuum leak.


SEE SAMPLE PICTURE HERE


This is a 20-30 minutes job.

Vacuum leaks can occur in following locations.


Intake manifold AND/OR vacuum lines.


Intake manifold is not accessible unless the engine head if off.

You can still check the potential leak by spraying some Berryman near the intake manifold.

Listen for rpm increase after you introduce the Berryman (FUEL) at idle.


Do the same starting from the brake booster unit (the round unit) on the drive side fire all.

Carefully listen for increase of RPM right after to spray the Berryman to the potential vacuum spot.

Get a friend to HEAR the ROM increase or monitor for RPM on the tech.

DO NOT AIM the Berryman into any heat source.


PLEASE RATE my answer if it is useful to you.

Posted on Dec 14, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 76,848 Answers

Check for intake vacuum leaks.

Posted on Sep 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 nissan quest that idle is high all the time went driving step on the breaks it filds it is never is goin to stop the transmission works verry hard


The idle speed of a warm engine should be 750 to 775 RPM. The idle is adjustable, but the idle could be high due to another sensor problem.
In that case a mechanic should do a scan to see if an error code exists.
Hope this helps.

Mar 30, 2015 | 2006 Nissan Quest

1 Answer

Idle is high


run fault codes and check the EGR valve and solenoid

Feb 01, 2014 | Chevrolet Suburban Cars & Trucks

1 Answer

Shuts off during Idle


Hi JESSE,HERE'S WHAT IT SAYS ABOUT THE IDLE CONTROL VALVE,AND HERE'S A LINK TO THE PART.
  • Regulates the amount of air entering the engine during idle
  • When not replaced, vehicle could experience high or low idle, engine dies at idle and/or severe high idle possibly causing internal engine damage and safety issues.Here's a link to the idle control motor.

Nov 05, 2013 | Chrysler Concorde Cars & Trucks

2 Answers

High idle


do u hav any $$ left-u went rong way-------cud be vacuum leak-some are hidden like on egr valves--but test idle air control and tps 1st--located at throttle body--buy a repair book or library sec629

Jun 26, 2013 | 2003 Ford Crown Victoria

2 Answers

Temp Gauge went to high


It could be 3 things: Temp sensor, thermostat, or fan relay. Fans don't usually turn on until car has been idleing for a while. I first would change thermostat, then relay, then temp sensor. Coolant must be 50/50 mixture for water pump to have proper lubricant from antifreezer. Do not go any further than a 60water/40antifreeze mix

Jul 08, 2009 | 1999 Honda CR-V

1 Answer

Not idling smoothly, sometimes having to restart at a stop w/ tranny in drive.


sure, that could be it. I would also suspect the fuel filter as well.

Jul 11, 2008 | 1997 Ford Aerostar Extended

Not finding what you are looking for?
2004 Jeep Liberty Logo

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...