Question about 1996 Chrysler Cirrus

1 Answer

Need location of crankshaft position sensor on a 1996 chrysler cirrus v6 location on engine and how to find it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chrysler Master
  • 3,433 Answers

The crank sensor should be found at the front by the crank pully. it is bolted to the engine wuth a wire connection plug on it.

Posted on Sep 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the Crankshaft Position Sensor location on a Town and Country with the 3.6L V6 engine?


The role of the crankshaft position sensor is to determine the position of the crankshaft, the crankshaft angle. It is usually with a camshaft position sensor work together - to determine the basic ignition timing. Car Diagnostic Tool

Aug 27, 2016 | 2011 Chrysler Town and Country

1 Answer

CPS crankshaft position sensor for a 1999 Chrysler Cirrus 2.5l v6 How do u get to the sensor and what is the steps to take to get it installed It is located in the back of the back of the engine. T


Here is info on a '96 Cirrus with same 2.5L engine. Check to see if same as yours.http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528008987d

Dec 30, 2012 | Cars & Trucks

1 Answer

I need a diagram of the location of the crankshaft position sensor for 1997 chysler cirrus 2.5 liter engine


try google and ask the question "where is the location of the crankshaft position sensor for 1997 chysler cirrus 2.5 liter engine" or you can go to a parts store and ask for there help, or buy a repair manual it will show you the location.

May 28, 2012 | Cars & Trucks

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

Sebring 1997 I need picture to lookat the PCM sensor and the Crankshaft position sensor (CKP sensor)


On 1997 Chrysler Sebring 2.5L MFI 6cyl...
- the PCM is located in the left side of the engine compartment, beside the Power Distribution Center (PDC).

zjlimited_767.gif

Fig. 1: Location of the PCM on the Cirrus, Stratus, Sebring convertible and Breeze models

zjlimited_768.gif

Fig. 2: Location of the PCM on the Sebring coupe and Avenger models

- the Crankshaft Position Sensor is located: under hood, driver side, upper engine area, mounted on end of engine block

zjlimited_769.gif

Fig. 4: Location of the crankshaft position sensor on 2.5L engines

Hope helps; remember to rating this answer and leave some testimonial comments.

Oct 09, 2011 | 1997 Chrysler Sebring

2 Answers

How do you replace the crankshaft positioning sensor?


well you did not list the engine . so here is all of them on the 2.0 or 2.4- 4 cyl the crank sensor is located behind the generator just abouve the oil filter mounted to the eng block. on the 2.5 V6-remove the speed control servo from the drivers side strut tower. (its located just under the distributer) remove the retaining bolt and pull the sensor straight up out of the transaxle housing

Jan 27, 2011 | 1998 Chrysler Cirrus

1 Answer

1999 CRYSLER CIRRUS NO SPARK,CHNAGE CRANK SENSOR,DIST, CHECK POWER/GROUND CKT OK


Either ASD relay in the fuse box in the front driver's side engine compartment or a burnt wire on the harness on the back of the motor going to the crankshaft position sensor.....
The relay can be swapped with one of the other relays because they are the same ones in the fuse box.

Oct 08, 2009 | 1996 Chrysler Cirrus

1 Answer

Need to change crankshaft positioning sensor


Changing the crankshaft will not solve the problem. Check all your connector to all the sensor. That you replaced . Look corrosion at connection points, also check your grounds

Jul 01, 2009 | 1996 Chrysler Cirrus

1 Answer

Check engine light comes on


Code 12 means That the Crankshaft position sensor may need replacement.It is located near the crankshaft maybe under the timing cover.

Apr 07, 2009 | 1995 Chrysler Cirrus

Not finding what you are looking for?
1996 Chrysler Cirrus Logo

864 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...