Question about Buick LeSabre

1 Answer

Need to replace low beam bulb. how do you get to it, do you take the two front bolts out

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 34 Answers

Most of the time you do not need to remove the headlamp. They can be reached from behind, though you may have to remove a cover to gain access. Grab the bulb at the base, twist and remove.

Posted on Sep 29, 2009

Testimonial: "I believe i will have to either remove the headlight or the battery as ther is not enough room, but thanks for the tip."

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE A HEADLIGHT FROM A 2007 SATURN OUTLOOK XE


Hi Carol , your going to have to remove the headlamp assembly to replace the bulb !


Remove the headlamp assembly. Refer to Headlamp Replacement.



1



Headlamp Bulb Accessory Covers (Qty: 2)



2



Headlamp Bulb Assembly (High Beam)




Caution: Refer to Halogen Bulb Caution in the Preface section.




Tip

Disconnect the electrical connectors and remove the bulbs.



3



Headlamp Bulb Assembly (Low Beam)


Callout

Component Name

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement .




Headlamp Assembly Bolt (Qty: 4)

Notice: Refer to Fastener Notice in the Preface section.

Tighten

6 N?·m (53 lb in)







2





Headlamp Fascia Brace Fender Reinforcement Bolt




Tighten

6 N?·m (53 lb in)







3





Headlamp Cam Adjuster




Procedure

Set the headlamp adjusters at the nominal setting of 6 turns off fully seated.







4





Headlamp Cam Locking Nut







5





Headlamp Assembly




Tip

Disconnect the electrical harness as the headlamp assembly is being removed from the vehicle.

Apr 08, 2015 | 2007 Saturn Outlook XE

1 Answer

Need to replace low beam light in my 2002 GMC Safari Van how do I do it?


Open the hood & near the top of the headlight you will see 2 bolts (10mm), remove them. You will notice the whole headlight assembly is loose from the top. Look down into the headlight assembly to the left & you will see another 10mm bolt that connects the outside light fixture. Remove the bolt & that light fixture will fall out (top first). Behind that light fixture you will see your last bolt when you look at the front of the vehicle. Remove it & now the entire light assembly will slide out & give you access to the both high beam & low beam bulbs. Hope this helps.

Read more: http://wiki.answers.com/Q/How_do_you_replace_the_headlight_bulb_located_on_a_1998_GMC_Safari#ixzz25o5cWhZA

Sep 07, 2012 | Cars & Trucks

2 Answers

How do I replace the headlight bulb on a 2005 Town Car?


1. Remove the three pin-type retainers, two screws and the radiator defector.
2. Remove the 4 bolts securing the headlamp assembly and remove headlamp assembly.
- Disconnect electrical connector
3. Remove the 3 hex-head bolts and 2 torx-head screws and remove headlamp protective cover.
4. *****Standard low-beam bulb*****
Disconnect the connector from the bulb and remove the low beam bulb.
5. *****HID low beam bulb*****
Release the spring tabs and remove the HID low beam bulb
Disconnect the connector from the bulb
6. *****High beam bulb*****
Disconnect the electrical connector and remove the high beam bulb.
Reverse order to install
dttech_6.gif
.
.

dttech_7.gif

Jan 27, 2011 | 2005 Lincoln Town Car

1 Answer

How to replace Head light & running light switch


remove the 4 bolts that hold the headlight assembly into the chassis frame.
For example, to remove the left front headlight;
It takes a 9006 low beam bulb, OEM is 51 watts If you buy a halogen upgrade, it will be a 55 watt bulb I don't know if you can put a super xenon bulb in there, it may harm the harness, I don't know so don't rely on me for that...
Lift the hood Get a socket head wrench and some SAE (standard) sockets. Find the socket that fits the bolt head just above the headlight. I think it is a 3/8's or slightly larger.
There are 4 bolts screwed through the frame into the top of the headlamp assembly. The bolts on each end of the headlight are longer and go all the way through the assembly to align it properly.
Lay each bolt out, on the ground in the order you removed them. The middle two bolts are short, maybe 1 " and the ends are closer to 3.5" long.
Once the bolts are out, slide the headlight assembly forward. There are two bulbs, a high and low beam. The low beam bulb is to the outside of the car, or drivers side on the left, farthest to the passenger side on the right.
Most of the time the low beam will burn out since it's used 90% of the time.
The bulb has a right angle fitting with a wiring harness attached. With your hand or a channel lock pair of pliers, gradually rotate the light bulb base counter clockwise until the unit is loose in the socket holder.
Disconnect the bulb from the wiring harness and replace it with the new bulb.
Reverse the process and turn on the headlights to check you have the bulb harness properly attached before finishing up the reassembly of the 4 bolts.
Your bulb alignment with the ground should not have changed from this work. Have fun...not difficult. Takes about 10 minutes per bulb.


Read more: http://wiki.answers.com/Q/How_do_you_change_the_headlights_of_a_94_Chrysler_LeBaron#ixzz19JuBNGBU

Dec 27, 2010 | 1992 Chrysler Lebaron

1 Answer

I need to change the low beam headlight bulb


  1. Remove headlight mounting bolts and nut
  2. Remove assembly
  3. Install headlight assembly (with new bulb)
  4. Replace/tighten headlight mounting bolts and nut
e2ac826.gif


Oct 30, 2009 | Hyundai Motor 2003 Elantra

1 Answer

How to change front headlamp bulb? Low beam


  1. Open the hood.
  2. Remove Grille.
  3. Remove the 2 retainers on back of headlamp assembly and remove the headlamp from the sheet metal panel.
  4. Remove the access cover from the rear of the headlamp.
  5. Disconnect the electrical connector from the socket.
  6. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  7. Disconnect the electrical connector from the socket.
  8. Remove the bulb and socket from the headlamp.
Installation Procedure Important: • Replace a high beam bulb with another high beam bulb. The high beam bulb has a black socket. • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.

Oct 14, 2009 | 2002 Chevrolet TrailBlazer

2 Answers

How do I change the low beam bulb(drivers side) on 2005 Pontiac Grand Prix?


Upside down L shaped bracket that is bolted to frame just behind headlight assy. Unbolt bracket, lift bracket straight up to unlock headlight assy. Headlight assy should easlier fall forward to replace any of the 3 bulbs

Sep 26, 2009 | 2005 Pontiac Grand Prix

1 Answer

2004 Lincoln Navigator Low Beam Bulb replacement


your owner manual will list the bulb. It is expensive. tascafordparts.com for discount from Ford Dealer

here's 2003, don't have 2004

Navigator high intensity discharge (HID) headlamp
  1. Remove the front radiator air deflector.
  1. Remove the three bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
1c293b4.gif
8. Remove the headlamp bulb protective cover(s).
  • Remove the HID lamp cover.
  • Remove the high beam cover.
  • Disconnect the electrical connector and push the grommet into the headlamp assembly.
7adecf7.gif
  1. Release the spring tabs and remove the HID low beam bulb.
3394a45.gif

Apr 11, 2009 | 2004 Lincoln Navigator

1 Answer

Replace low beam headlamp, passenger side, 2004 Navigator


Remove the front radiator air deflector.
Remove the three bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
ef5d2b9.jpg
Remove the headlamp bulb protective cover.
1 Low beam cover. 2 High beam cover.

babb381.jpg
b8093f8.jpg

Feb 13, 2009 | 2003 Lincoln Navigator

3 Answers

REPLACEMENT OF [LOW BEAM] HALOGEN BULB IN 2004 Buick LeSabre


I just Replaced a Low Beam Light bulb on a 2005 Buick La Sabre.

If You use a Metric socket and Remove the Two Silver bolts Attaching the headlight Assemble onto the metal surrounding the the lamp assembly it comes out to the front. This makes it much easier to access the bulb. Twist it counerclockwise & it comes out by pulling gently on the bulb. Then by realeasing a tab that is the socket holder bulb can be removed & replaced with a New #9006 low beam halogen light bulb. Wrap a Paper towel around the bulb & do NOT touch it with your bare hand as this wiil ruin a halogen bulb,

Jan 22, 2009 | 2004 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...