Question about 1997 Lincoln Continental

1 Answer

Removal of to cover on engine, need to replace plugs?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Lincoln Master
  • 632 Answers

If I am not mistaken this cover has black plastic retainers that can be removed with a 1/4 drive ratchet and/or extension.

Posted on Oct 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cam shaft position sensor on a 2001 izuzu rodeo 2.2. 4 cyl automatic


the sensor is under the timing belt cover at the top of the engine. If you are looking at the engine you'll see a black strip covering your spark plugs, your electrical connection on the camshaft position sensor is under there go ahead and disconnect the sensor. Next is the removal of the timing belt cover. You will need to take the bolts holding the cover in place they will hold it all the way down to the bottom of the engine. The bolt in the center top section is actually the bolt holding the sensor in place inside the engine so you will need to look and see how to maneuver the sensor out after the bolt is removed. Replace with new sensor and replace bolts. Plug electrical connector into the top of the sensor and replace spark plug cover. You are now done.

Sep 11, 2012 | 2001 Isuzu Rodeo

1 Answer

Removal of back spark plugs on 2003 buick rendevouzs


if this has the 3.8 or similar, go under alternator to access the back left plug, then work from top of engine and remove whats necessary to get to other 2 plugs. use a spark plug socket and 3/8 ratchet to remove the plugs. and universal if need be. good-day !

Mar 22, 2012 | 2003 Buick Rendezvous

1 Answer

Removal of plug wires on 2000 Chev silverado


Underneath the hood is the engine.On top of the engine is a big plastic cover, cover entire top of engine.
Example: http://image.trucktrend.com/f/8511504/112_0507_02z_2005_chevrolet_silverado_ss_pickup_engine.jpg

Remove the cover by taking out the bolt/screws on the top of the cover.
Once removed the plug wires are clearly visible.
Take pictures or mark where the wire are plugged into.
One at a time!!! remove one wire and replace it with a new one.
Put it back together

May 30, 2011 | 2000 Chevrolet Silverado 1500

1 Answer

How to replace cam position sensor on a 2002 isuzu rodeo 2.2 engine


the sensor is under the timing belt cover at the top of the engine. If you are looking at the engine you'll see a black strip covering your spark plugs, your electrical connection on the camshaft position sensor is under there go ahead and disconnect the sensor. Next is the removal of the timing belt cover. You will need to take the bolts holding the cover in place they will hold it all the way down to the bottom of the engine. The bolt in the center top section is actually the bolt holding the sensor in place inside the engine so you will need to look and see how to maneuver the sensor out after the bolt is removed. Replace with new sensor and replace bolts. Plug electrical connector into the top of the sensor and replace spark plug cover. You are now done. have a good day !! 2.2 engine,

Feb 26, 2011 | Isuzu Rodeo Cars & Trucks

2 Answers

Replacing waterpump in1999 nissan pathfinder


Water Pump Removal & Installation To Remove:
  1. Allow the engine to cool and drain the coolant from the radiator and both engine block plugs.
  2. Remove the fan shroud and both radiator hoses.
  3. Remove the drive belts.
  4. Remove the water pump pulley.
  5. Remove the crankshaft pulley.
  6. Remove the timing belt covers.
  7. Remove the water pump.
Water pump removal/installation 7924vg20.gif

To Install:
  1. Install the water pump with new gasket.
  2. Install the timing belt covers.
  3. Install the crankshaft pulley.
  4. Install the water pump pulley.
  5. Install the drive belts and fan shroud.
  6. Install the radiator hoses.
  7. Install the coolant drain plugs.
  8. Refill the cooling system.
prev.gif next.gif

Aug 10, 2010 | 1997 Nissan Pathfinder

1 Answer

Dont know how to take master cylinder off to replace coil pack


You shouldn't have to remove it....here are the steps from the tech manual:

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Label and disconnect the spark plug wires from each of the coil pack towers.
3db79bc.gif
Ignition coil removal—2.4L engine

2f61688.gif
Ignition coil removal—3.3L and 3.8L engines


  1. Disengage the electrical connector from the ignition coil pack.
  2. Remove the coil pack mounting fasteners.
  3. Remove the coil pack from the vehicle. If equipped, remove the coil pack from the mounting bracket.
To install:
  1. Place the coil pack into position on top of the engine valve cover, or mounting bracket, if equipped.
  2. Install and tighten the coil pack mounting fasteners to 9 ft. lbs. (12 Nm).
  3. Plug in the electrical connector to the ignition coil pack.
  4. Connect each spark plug wire to each corresponding coil pack tower. The coil pack towers are numbered with the correct cylinder identification. Be sure that the spark plug wires snap firmly onto each coil tower.
  5. Connect the negative battery cable.

Jan 18, 2010 | 2001 Chrysler Voyager

3 Answers

Need to replace the spark plugs


The top of the engine has a cover remove to see ignition coils. Remove wires then coils, plugs are under coils. This is called coil on plug system. Make sure engine is over night cold before you do this, aluminum heads are easy to pull threads when they are hot. Always replace with OEM plug cheap plugs burn out coils !!!

Sep 27, 2009 | 2005 Toyota Corolla

2 Answers

How do i put a coil in a 2001 jaguar s type


303-07A: Engine Ignition — 3.0L (4V) 2001 Lincoln LS Workshop Manual DESCRIPTION AND OPERATION Engine Ignition The electronic ignition (EI) system is a coil-on-plug (COP) ignition system.
---------------------------------------------------------------------------------------
SECTION 303-07B: Engine Ignition — 3.9L 2001 Lincoln LS Workshop Manual
DESCRIPTION AND OPERATION Engine Ignition The electronic ignition (EI) system is a coil-on-plug (COP) ignition system
-----------------------------------------------------------------------------
v-8
SECTION 303-07B: Engine Ignition — 3.9L 2001 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Ignition Coil Removal
  1. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 .
  1. Remove the bolts and the ignition coil cover.
7b000cd.gif
  1. Disconnect the electrical connector from each ignition coil.
a1d93dd.gif
  1. Remove the ignition coils.
    1. Remove the bolts.
    1. Remove the ignition coils.
------------------------------------------------
v-6

SECTION 303-07A: Engine Ignition — 3.0L (4V) 2001 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Ignition Coil Removal
  1. Remove the engine appearance cover.
  1. To access the RH bank ignition coils, remove the upper intake manifold. For additional information, refer to Section 303-01A .
  1. Disconnect the electrical connector from the ignition coils.
  1. Remove the bolts.
  1. Remove the ignition coils.
please rate as fixed if this helps.

Apr 28, 2009 | 2001 Jaguar S-Type

1 Answer

96 buick skylark 2.4L Engine runs but misfires, multiple cylinders


Remove the cover on top of the engine. It has fouth 10mm bolts that hold it on. This car has individual ignition coils for each cylinder. Remove the wiring harness connectors from each one, then remove the ignition coils. Check each coils resistance with an ohm meter, they should all have about the same resistance. If one is really low, high, or has no continuity, it will need to be replaced. You will notice that the coils have what is called a "plug boot" attached to each of them. First inspect them, and make sure there are no burnt places on them. If they have oil on the, you will need to replace the valve cover gasket. Next remove the plugs, and inspect/replace them. Assembly is reverse of removal. This should take care of it.

Mar 26, 2009 | 1997 Buick Skylark

Not finding what you are looking for?
1997 Lincoln Continental Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

fordexpert

Level 3 Expert

5481 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...