Question about Fiat Strada

1 Answer

Brake Pedal creeps down when held under pressure

I have a Fiat Ulysse (53 Reg) which has just failed its MOT because the Brake Pedal creeps down when held under pressure

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Bleed all ure brakes

Posted on Jan 11, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2004 fiat ulysse 2.0 petrol the headlights go on and off on their own and the wipers. the horn doesnt work and the airbag light is on has anyone got any ideasplease

This must be something related to electric problems.... Looks like you have loosen connection somewhere..... I would check - (ground) on your battery (in Ulysse is under floor in front of passengers seat) and then ground cable leading to fuse box (behind the right headlamp unit under hood).
it also can be loosen fuse, but it would make problem just with one device.... if this won't help, take it to electrician

Jan 26, 2014 | 2006 Fiat Ulysse 3.0

1 Answer

Brakes work fine until I stop then the pedal goes to the floor. I thought it was the master cylinder but new one does the same. I replaced the check valve but it didn't correct the problem. It doesn't...

Pressure is bleeding...start with the simplest fix: Replace the cap gasket.
They're cheap, and notorious for bleeding pressure before failing altogether.

When you park in the driveway tonight, go in and get a pair of jeans on and a flashlight and take a good look under the car for shiny/wet spots around the wheels.

You could have a bad cup liner in one of the wheels, and if it's cracked (aged) it will bleed a bit under pressure...not enough to make a puddle, but it will drip down the inside of the wheel.
When you move again, the brake fluid is wind-sprayed around the wheel.

Assuming a new cap gasket and dry wheels; Your search for fluid leaks will have to expand, starting with the transition hoses (the rubber sections that are joined to the metal lines) just behind the brake calipers.

***Don't forget to VOTE for the guys who take an interest in helping!

Apr 20, 2010 | 1997 Lincoln Mark VIII

1 Answer

I have a fiat ulysse and the power steering belt

yes, sounds like the pully is no good, may have bad bearings in pulley, replace it.

Jan 03, 2010 | Fiat 124 Cars & Trucks

1 Answer

Light on dash of Fiat Ulysee coming on. It a

That light is telling you that your brakes are worn. There is a wire connected to the front brake pads, and when the brakes reach a certain point, they trigger the light. Sometimes the light is triggered prematurely if one of the wires breaks or gets disconnected. Either way, you should check your brakes. As for the Fiat lights being the same, you are mistaken with your particular vehicle. The Fiat Ulysse is actually made by Peugeot, and is identical to the Peugeot 806, the and the Citroen Evasion.

Oct 17, 2009 | 2005 Fiat Pininfarina

1 Answer

Fiat Uno Pacer - Brake Booster not assist braking

it could be that the master cylinder is bad or the brake booster is bad also check the vacum hose going to the brake booster if it has a hole in it it will lose pressure and make the engine lose rpms

Aug 16, 2009 | 2006 Fiat 124

1 Answer

Brake pedal keeps creeping down, but there are no leaks.

you still have air in the system you need too bleed it some more

May 21, 2009 | 1991 Chevrolet C1500

1 Answer

Brake pedal keeps creeping down, but there are no leaks.

check your brake booster and also make sure the rear shoes are adjusted up where they belong. If they are not adjusted up the brake pedal will go farther and farther toward the floor and get spongier as they go farther out of adjustment. If you adjust them up and they back down again change your self-adjusters and springs. They are readily available at your local parts store.

May 10, 2009 | 1991 Ford F350

1 Answer

Audi A3 diesel 2000 reg brake pedal going to the floor with engine running and heavy pedal pressure

you should have bench bleed the master cylinder first before installation return cylinder and get a new one than bench bleed it first than install it to car once installed you may have to bleed each wheel

Jul 06, 2008 | Audi A3 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

78257 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides