Question about 2000 Toyota 4Runner

1 Answer

Clutch pedal spring squeaks, i need the new white plastic bushings that go on the end of the springs.

Posted by on


1 Answer

Go to Dealer and get it from parts dept

Posted on Sep 28, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Clutch pedal noise

This may be from a dry pivot bush or spring squeak. It can also be from a failing clutch master cylinder or a failing clutch cable

Apr 09, 2014 | Hyundai Motor 1995 Accent

1 Answer

Why does my clutch squeak when depressed

spring above the pedal might be dried as long as gears are engaging ok. nothing to worry about.
also check the clutch cable as well..

Mar 30, 2014 | 2006 Citroen Xsara Kombi

1 Answer

Squeaking suspention

The Explorer has an unusual front suspension called a Torsion Bar system (no springs). As they get older, they squeak and groan.
All the parts are put together with bushings between the metal parts, and as these get older, the get dry and inflexible. And this causes the groans and squeaks.
At worst, they can make your handling sloppy. A new set of control arms, tie rod ends and ball joints is about $200 in parts, plus 3 hours of shop time to replace them. When you replace these parts you also get new bushings which usually stops the noises.

Oct 26, 2013 | 1996 Ford Explorer

1 Answer

2006 dodge charger front end squeaking

First you need to check your outer tie rod ends, then you need to check your lower control arm bushings also you will need to look at the sway bar bushings. That is what I have found worn out on my 2006 dodge daytona charger

Apr 08, 2012 | 2006 Dodge Charger

1 Answer

Squeaky clutch pedal

This is a common problem. Your clutch pedal has a return spring on it, each end of which can squeak when dry.
Look under the dash, and locate this. Dab a bit of grease at each end of the spring where it hooks around. Work the pedal up and down a few times and the squeak should go the way of the Honda Element.

Nov 28, 2011 | 2003 Honda CR-V

1 Answer

Clutch pedal noise in hot weather

Pivot of pedal srm needs Lubrication. Heat expands bushings and such. If it is the pedal return spring , lub the springs where they hook on each end.

May 23, 2009 | 1998 Saturn SL

1 Answer

Ford f 150 1988 clutch has no spring and lays on the floor

Get your face near the floorboard, and look at the clutch pedal. Now look at what is connected to it that runs through the body and down toward the tranny. If this rod moves in and out of its hole when you move pedal...

...then stick your head under vehicle and find where this rod comes out. There is another rod hooked to it that actuates the clutch. One of these has likely fallen off, due to a worn rod and bushing. Sometimes they are so worn, they must be replaced. If you catch it in time, you can replace the plastic bushing and/or just snap it back together. Sounds like your linkage has come apart between pedal and clutch. Rod has some adjustment, but only to a point.

Mar 20, 2009 | 1996 Chevrolet Blazer

1 Answer

Problem: clutch pedal broke, sping came off!

The white plastic sleeve is an integral part of the clutch cable assy. You can get a cable at Autozone for about 12.00 plus tax. Replacement is easy, and the hardest thing involved is readjusting the free play in the cable after installation!

Sep 16, 2008 | 1987 Volkswagen Scirocco

2 Answers



To my knowledge, the spring is merely to assist the pedal to return at its default position (clutch engaged), that is pedal up. Normally, it would have an exaggerated j ends. The ends are meant to hook to two (2) slots, one at the pedal itself, the other at the bracket/housing or firewall and not replace the entire clutch assembly. Having said that and as per your post, the clutch works fine, it is a matter of finding a replacement spring of similar physical characteristics/dimensions and hook in place. Hooking in place is relatively easy saved that you have to crouch down and use a long noise pliers. A mechanics troubleshooting lamp would help seeing where the j ends would and should go into.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Jun 17, 2008 | 2005 Mazda 3

Not finding what you are looking for?
2000 Toyota 4Runner Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides