Question about 1997 Cadillac DeVille

1 Answer

Engine removal I am trying to remove an engine from a deville and need to get the tourqe converter bolts out

Posted by on

Ad

1 Answer

What is your question.? It should come out with the converter still bolted to the eng flywheel. If your pulling a front wheel drive vehicle motor you drop the trans out the bottom first, then pull the engine. You can also drop both together by dropping the support cradle. That is the best way and the way it was built and done in a dealership in some cases. Trans got go to have roon

Posted on Sep 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to remove the exhaust manifold on the right side of a 94 4.9l engine in a cadillac deville. It has a broken bolt in the exhaust. What is involved in removing the manifold?


I suggest you use all new exhaust manifold hardware and torque new bolts to 20 Ft Lbs.
4.5L and 4.9L Engines
RIGHT
Disconnect the negative battery cable. Remove the air cleaner. Remove the exhaust crossover pipe. Disconnect the oxygen and coolant temperature sensors. Remove the catalytic converter-to-AIR pipe clip bolt. Remove the upper manifold-to-cylinder head bolts. Raise and safely support the vehicle. Disconnect the converter air pipe bracket from the stud and remove the converter-to-manifold exhaust pipe. Support the engine cradle with screw jacks and remove the rear cradle bolts. Loosen the front cradle bolts and slightly lower the Engine cradle. Remove the remaining exhaust manifold-to-cylinder head bolts, the AIR pipe, and the manifold. Clean the gasket mounting surfaces.
To install:
Install the exhaust manifold and replace the AIR pipe. Tighten the manifold mounting bolts to 16-18 ft. lbs. (21-24 Nm). Install the manifold-to-converter exhaust pipe and replace the converter air pipe bracket to the stud. Raise the Engine cradle and install the rear cradle bolts. Tighten to 75 ft. lbs. (102 Nm). Lower the vehicle. Replace the upper manifold-to-cylinder head bolts. Replace the converter air pipe to AIR pipe clip bolt. Connect the coolant temperature and oxygen sensor connectors. Replace the exhaust crossover pipe. Replace the air cleaner and connect the negative battery cable. Start the Engine and check for leaks.

Mar 28, 2017 | Cadillac Cars & Trucks

1 Answer

What bolts have to be removed to drop transmission on 84 dodge 600


Wireing harness needs disconnected
Transmision lines need disconected
If 4 wheel drive then transfer case needs removed
front and rear drive shafts need removed
If you have torsion bars they need to come out.
Then if im correct there are 8 bolts on the bell housing and the transmission cross member has 4 bolts if your exhaust pipe is in the way then that also has to come out.
Dont forget to take off your shift cable
Before you can remove the transmission you will need to take off the 4 to 8 tourqe converter bolts through your inspection port or the transmission will stay locked to the flywheel and you can pull and pry all you want and not move it at all.

Nov 06, 2015 | Dodge Cars & Trucks

1 Answer

I'm removing and planning to rebuild my 93 land


It is actually easier to pull them both because of the top bellhousing bolts and the tourqe converter bolts.

Jun 05, 2011 | 1993 Toyota Land Cruiser

1 Answer

Replacing the transmission in my 2000 chevy truck 5.3 four wheel halfton got the tranny and the tourqe converter is still on the flywheel but can't figure a way too loosten the tourqes holding it to...


You'll need a box end wrench and a pry bar. Use the pry bar to hold the ring gear against the motor while you use the box end wrench to remove one bolt. Then rotate the engine with the bar to bring the next bolt around to where you can get the wrench on it. Repeat until you have the bolts off. Do not lose those bolts. If you do they will have to be ordered at the dealer.
When you put the torque convertor back in the transmission it has to go in two steps. It will slide in so far and then you will have to turn and push until it goes in again. If you don't do this the trans will not mount flush with the engine. When it's in the transmission properly it should sit about an inch inside the housing. Hope this helps.

May 06, 2011 | 1999 Chevrolet K1500

1 Answer

How hard is it to install oil pan on my 2000 deville, northstar engine


I worked on a 1999 Deville and to remove the oil pan wasn't to bad to change. All I had to do was Jack up the car and support it.Also remove the negative battery terminal.Drain the oil then remove the torque converter cover bolts and then the oil pan bolts and remove the oil pan.On some model Cadillacs there is also an exhaust cross under pipe that also has to be removed.Be sure not to over tighten the oil pan bolts there real hard to get out if you break one.Your going to have to find out how tight they should be because they all very depending on the vehicle.Most all of your auto parts stores have this information.

Feb 25, 2011 | 2000 Cadillac DeVille

1 Answer

I have a 1989 caddy sedan deville. The smog pump seized up and froze. I need to remove this pump. How long of a job is this and can I gut the insides of the pump out and replace it as just an idler pulley?...


Replace the pump as it does other things than just pump air into the exhaust. I helps in cold starting and keeps the engine from backfiring during deceleration. You can cause the converter to fail also. I have a service manual and it tells you to first loosen the pulley bolts on the pump first then remove the belt and pulley. Remove inlet hose and outlet hose then the mounting bolts .

Apr 13, 2009 | 1989 Cadillac Sedan DeVille

Not finding what you are looking for?
1997 Cadillac DeVille Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...