Question about 1985 Dodge Pickup 4WD

Open Question

Need to know how to remove the bearings on the front spindles on a 4 WD 1985 dodge truck 250 3500lb front axles. they look like they should just slide out since i removed the gasket but they do not. I replaced the U joints and thought I should go ahead and replace bearings and oil seals(done with oil seals). I have tried prying them out but they are in there pretty good, didnt know if someone had a trick i could use or is there a special tool one needs. Thanks Billy

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u remove hubs on a 1992 Isuzu big horn


TO DO WHAT? not even the smallest hint on job or failure.>?
USA?
hubs, the rears have hubs to with disc brake option.rotor hubs.
I guess front hubs?.
guess 2, wheel bearing hubs, and not 4wd axle locking hub units.
doing what?
brakes, wheel bearings, axle damage. 4wd axle bearings what?
the pages are 2wd pages, and 4 wd pages, which is yours?
is this your first time DIY ever. ? or first time 4wd?
guess 3, 4wd, how am I guessing....


names
Acura SLX
Chevrolet Trooper
Isuzu Bighorn
Holden Jackaroo
Holden Monterey
Honda Horizon
HSV Jackaroo
Opel Monterey
Subaru Bighorn
Vauxhall Monterey
wow......
our usa book lists it as trooper only.
so ...

just B or B then A off? if you had b off, you'd see what?, a big nut.
that is locked to spindle shaft.
ill guess? wheel bearings are bad? (just in hub not spindle bearings bad... no matter this is first.)
so you do what. ? here are the steps.

that part"B" must be off first, see the bolts holding it, ?
B = auto locking hubs. or hub axle lockers.
26005769-b5pjo3cin0lhc1b54v4xlnuy-4-0.jpg you can see the caliber must come off, so, do so and tie them up.
  1. "Place the Transfer shift in the 2H position.
  2. Raise and support the front of the vehicle safely on jackstands. (rear tires chocked, and hand brake set hard)
  3. Remove the wheel and tire assembly.
  4. Loosen the hub to rotor retainer bolts.
  5. Remove the brake caliper mounting bolts and carefully remove the caliper (along with the brake pads) from the rotor. Do not disconnect the brake line. Secure the caliper out of the way with the flexible line still connected.
  6. Remove the hub nut using hub wrench J-29020-A or equivalent. ( special tool)
  7. Remove the hub cap assembly retainer bolts. Remove the spindle nut, washers, and other components. Remove the hub/rotor, being careful not to drop the outer wheel bearings. As the hub/rotor is pulled forward, the outer wheel bearings will often fall forward.
  8. Once the hub/rotor is removed, remove the retainer bolts securing the rotor and hub together. Inspect the hub and replace if needed."
  9. end removal. install is next... (alldata.com covers this)

Dec 13, 2015 | Isuzu Cars & Trucks

1 Answer

Do you have a video on how to remove front roter on a 95 dodge ram 2500 4 x 4


first remove center axle nut 1 11/16 then jack up & support truck remove tire then brake caliper then on the back side of knuckle remove the three bolts that hold wheel bearing onto spindle . then lightly tap free (not heavy force)

Jul 30, 2014 | Cars & Trucks

1 Answer

Cant figure out how to get the front driverside axle out of my 05 dodgeram


Remove the hub if the axle nut is loose. Look at the inside of the spindle, you'll see three bolt heads. They hold the hub and bearing in place. Once you remove them, the hub and bearing will come out giving you enough clearance to pull the axle out through the hole.

Mar 14, 2010 | 2005 Dodge Ram

2 Answers

Change the front wheel bearings on a 2005 taurus


Remove wheel
Remove axle nut
Remove outer tie rod nut
Leave outer tie rod nut on 3-4 threads
Hit spindle area where tie rod is mounted very hard with a large hammer (wear Saftey glasses)
The tie rod should loosen up and you remove it off spindle.
Remove lower ball joint nut
Leave nut on 3-4 threads
Hit spindle area where ball joint mounts (wear saftey glasses)
Carfully pry down the lower control arm too remove ball joint from arm.
Press in the axle towards the trans. out of the wheel bearing.
Place a piece of wood between the shock and inner fender to give yourself room to work.
Remove the three 15mm bolts that hold the wheel bearing on.
Hit wheel bearing out with hammer (wearing saftey glasses)
You may need to break a sweat on this part. Somtimes they are rusted in.
Be carfull not to damage the ABS sensor.

Reverse procedures to install

Sep 08, 2009 | 2005 Ford Taurus

2 Answers

Replacing front drive axle universal joints.


remove front wheel brakes,rotors, axle nut,remove the four bolts on the bake side of your unit bearing using one of the 4 bolts removed from the unit bearing (also knowin as wheel bearing) go get a half dozen of the same bolt only 1 to 2 inchs longer theard them into the unit bearing from the back side and start beating. the unit bearing is a sob to get out but will come out with time once you get it out pull out your axle shaft replace the ujoint and reassemble anti seize everything as you re assemble it

Jul 09, 2009 | 2004 Dodge Ram 2500

1 Answer

Front left spindle bearing was toast


i have a 83 dodge w150 it has 14 in of lift on 39.5 super swampers and im goin threw wheel bearings every 3 weeks any solutions ? thanks

Jul 05, 2009 | 1986 Dodge W150

1 Answer

Upper and lower ball joint replacement


to remove the axles, remove brake caliper and disc, remove hub assembly, the center hub/axle nut and...(there are i think 3-4 bolts on the back side of the spindle to remove the hub), you may have to force the hub off the spindle with a hammer or air hammer... once the hub is out the axle should slide out of the front differential allowing access to the ball joint nuts for removal...

Jun 12, 2009 | 2000 Dodge Ram 1500 Truck

1 Answer

1988 dodge aries


cv axle to spindle 177 ftlbs

Feb 04, 2009 | 1985 Dodge Aries

1 Answer

Front wheel bearing 2004 escape 4x4


It's nearly impossible unless you have a good air compressor and a powerful 1/2" or larger drive impact gun.The reason is you have to remove the cv axle nut and axle out of the way before removing the bearing and hub.The axle nut requires a couple hundred foot pounds to remove.The procedure is:Jack vehicle safely off the ground,remove wheel and tire.Remove axle retaining nut.Remove balljoint nut and bolt,pry down on lower control arm,and disengage balljoint and lower arm from spindle.Now the axle can be released from the hub,but leave the other end of the axle in the trans,just set off to the side out of the way.At this point,there are two ways to change the bearing.The wheel bearing is a double roller,cartridge type with the hub containg the wheel studs,pressed into the bearing.Remove the entire spindle assembly from the suspension strut,OR leave the spindle attached to the strut,and remove the bearing and hub from the spindle.Some guys swear by taking the spindle to a press,and pressing the bearing assembly out with a bottle jack.I just use a bushing driver set,and ball peen hammer,and remove the hub from the bearing...then remove the snap ring retaing the bearing in the spindle,then drive the bearing out of the spindle with the hammer and drivers.There you have it.Reverse procedure for reassembly

Jul 11, 2008 | 2004 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...