Question about 1999 Mercury Tracer

Open Question

On a 1999 Mercury Tracer, how are the pastic clips released that hold the rear light covers in place (without breaking them)?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replace license plate lights


Hi there,

Firstly, remove the four screws on the bottom of the license plate light assembly using a Phillips screwdriver. Then pull the license plate light cover out away from the rear of the car. Pull the bulb forward and pull it straight out of the wiring socket.

A press the new bulb into place until it is secure. Push the bulb and wiring assembly back up inside the light assembly and replace the license plate light cover. Replace the four screws that secure the light cover and tighten them with a Phillips screwdriver. Finally, turn on the lights to test the new bulb.

Hope this helps...

Jan 17, 2011 | 2007 Toyota Sienna

1 Answer

Need to replace inside door handle that broke completely off. How do I replace this section?


you will need to remove the cover around the handle they are easy to brake from the inside of the outside cover ring go from the inside with a small screw driver and slide between and pry the cover up it has 4 mounting points top left top bottom right and left.
next pop off the switch from the front slide a screwdriver at the front leading edge and push it towards the back of the door panel and lift gently there is a flange on the rear of it that holds the rear of the assembly down dont pry up on the back lift the front and slide it forward unplug all the wires. remove the two screws inside the door arm rest where you pull the door shut. the cup to close the door. next you need to remove the mirror cover at the front top of the door panel slide a screwdriver pry
straight out. using a door panel clip tool. slide under the panel at the bottom rear corner to find the clip and pry the clip out of the hole. work your way around the door to each clip. sometimes you can pull the panel off with your hands but if you are not experirenced you might break some clips or the door panel be nice to it dont break things. all the way around the sides and the bottom are released then pull away from the door and hold the bottom and lift up and hit the top of the door handle with your hand so the clips will release accross the top. remove the light socket from the rear bottom of the door. place the panel somewhere so you dont scratch it up. now remove the rivet from the handle. I punch the center out then use a sharp chisel to punch it off. you may want to drill the rivet. up to you. then the handle slides forward and you have to disconnect the linkage clips from the handle. install the new handle make sure the lock rod is in the hole that slides the lock. hook up the linkages new slide back in position and rivet then reverse the prosess of removing the handle

Dec 12, 2010 | 1999 Chevrolet Suburban

2 Answers

How to channge fuel filter for 1998 mercury tracer


Usually there is a worm gear clamp holding the filter to the bracket. There are 2 plastic clips, one on each connector going to the fuel filter, remove both clips and pull the lines off the filter.

Oct 19, 2010 | 1998 Mercury Tracer

2 Answers

How to replace rear wiper blade - "07 Hyundai Santa Fe


pull the arm out,towards you ,then press the small tongue on the plastic clip and slide the pastic bit down the arm and off. replacement is a push fit until the clip clicks into place.

Jul 29, 2010 | 2007 Hyundai Santa Fe Limited

1 Answer

1999 Chrysler Concorde LXI Rear Speaker replacement


If you mean the rear shelf removal, then you begin by removing the rear seat (lift to release the corner clips on each side holding the cushion to the floor). Then remove the fasteners for the seat belts, then lift the seat back to raise and release it from its clips, and remove it from the vehicle. There are then a lower and upper trim panel around the back shelf that you need to remove (these may be on each side of the shelf, e.g. they are called 'quarter trim' panels). Then you will see some push-pin fasteners that hold the shelf across the front lower edge, so you gently pry out the center push-pin of each one of those to release the fastener. Then you pull the shelf forward to release it from the clips that hold it under the window. Then remove the wire to the center high-mounted brake light. The panel with its speakers attached can then be removed, but also remove the wires from the speakers so you don't break those. connections.
That is the procedure as shown in my '98 manual.

Mar 31, 2010 | 1999 Chrysler Concorde

1 Answer

My brake lights on my 1999 mercury tracer will not go out. how do I fix them?


They're is a part called a Brake Switch right in front of your pedal. This works the opposite of most switches, as in when you press the pedal and the button is released, your brake lights come on. It's possible that it needs to adjusted or even replaced. Hope this helps.

Jul 28, 2009 | 1999 Mercury Tracer

1 Answer

1989 mercury tracer will not idle and does not stay running without pumping the gas and when you push the clutch in the rpms drop immediatly and will die if dont pump the gas and if it drops below 2000 rpm...


Is the check engine light on? I would take it to an auto parts store and have any codes read. It sounds like a possible problem with the throttle position sensor. It is located under hood, center, upper engine area, rear of valve cover, mounted on driver side of throttle valve assembly. Good luck and hope this helps.

Jul 15, 2009 | 1989 Mercury Tracer

2 Answers

Need to replace my dpfe sensor on my 1999 mercury mountaineer. Where is it, i would like to change it myself


I believe the sensor that you are looking for is on the drivers side of the engine. If you have a 4.0 SOHC engine or a 5.0 engine the wiring will be the same. You will have a brown with a white tracer, a brown with a light green tracer, and a grey with a red tracer to the sensor. If you you have a 4.0 EI then you will have a Brown with a white tracer and 2 brown with a light green. If you follow the 2 tubes coming up from your exhaust manifold you should be able to locate your sensor it will have to tubes or hoses going to it from your exhaust manifold. Good luck.

Apr 17, 2009 | 1999 Mercury Mountaineer

1 Answer

1995 Mercury Tracer Rear lights not working


does the Center brake light work ? I think your looking at replacing the brake light switch !

Dec 19, 2008 | 1995 Mercury Tracer

1 Answer

How to get brake pads off with pin holding them on?


Using a needle nose pliers pull wire clips that hold pins in place, they are on top of the caliper, then remove pins. Good Luck If I fixed ya leave me a FIX-YA Comment. Thanks

Dec 17, 2008 | 1997 Mercury Tracer

Not finding what you are looking for?
1999 Mercury Tracer Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

fordexpert

Level 3 Expert

5471 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...