Question about 2008 Ford F 450 Super Duty

Open Question

How to change the turn signal light in the passenger side mirror

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
smartr10U
  • 1305 Answers

SOURCE: wiring lights in side mirrors

Here is a link to a pdf (acrobat reader) file This pdf will show you how to run the proper wiring to your turn signal mirrors..
Cool upgrade!
Let me know how you like them after install.
K

Click here for pdf

Posted on May 31, 2009

Ad
pippall
  • 1486 Answers

SOURCE: 2006 Ford Ranger. Rear passenger side tail light

Bad earth connection.Clean or replce wire.

Posted on Jun 18, 2009

  • 60 Answers

SOURCE: Passenger side mirror replacement procedures

If its a power mirror there is more thing you will have to remove to get to the wires but if not there is a screw on the corner piece on the inside of the door. just pull the screw out and the bolts (3) that hold the mirror on are behind it. If it power then you will have to remove the door panel to access the wiring to disconnect it

Posted on Jun 21, 2009

  • 1986 Answers

SOURCE: how to install passenger side view mirror Ford

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

sscullys
  • 984 Answers

SOURCE: change mirror turn signal light in ford 2001

You will need to remove the glass to get to it.

Muth Co signal mirrors have some good directions for getting the door panel off, and removing the glass, available for download on their site.

I prefer to do this with the mirror head off the truck, but you might feel other wise on this part.

Once you have the glass from the mirror removed you will see where the bulb is inserted from the back ( inside ) of the mirror head.

Posted on Nov 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a short in dash and running lights. When I turn on the dash /running lights it always blows the fuse. how do I begin to fix the problem?


do you have a trailer lighting possible short there or where it was hit there is a wire pinched and shorted

Nov 30, 2014 | 2001 Nissan Xterra

1 Answer

Outside mirror turn signal on 2001 Lincoln navigator does not work


I have changed many of these...Everytime I inspect one it is always the light that is faulty...and that is all different makes..I have found some have a left and right fuse but it was always the light..The mirror will slightly pivot..carefully pivot mirror slightly inward you will notice it is only held on with plastic clips..Use a good flashlight.....you can actually see behind mirror better at night with a direct beam small led pocket light...use a pocket screwdriver and carefully pry the clips away from mirror while softly pulling on mirror...All you have to do is release the 2 upper and lower outside clips and it will slide out..Then you will see the 2 screws that mount the signal light to the mirror housing..just remove and replace..re-install all the way it was removed...Do it carefully....easy job...

Jun 16, 2014 | 2001 Lincoln Navigator

1 Answer

Turn signal bulb was working, now it isnt


its is not uncommon for the contacts in the sockets to become corroded or just expand to the point of where they do not contact the bulb,try to test the socket with a multimeter for voltage,if it has voltage then its most likely the contacts,which sometimes can be rebent,but replaceing the sockets is a better solution,and can be picked up at most stores or 4x4 shops and junk yards.

Dec 14, 2011 | 1998 Jeep Cherokee

1 Answer

Changed multi function switch, bulbs, and passenger side rear light assembly (reverse, blinker, brake light). Everything works except the rear passenger side turn signal but the front passenger side is...


You have a bad connection at the rear passenger side turn signal. It is either the connection is corroded or a wire is loose on the ground side of the circuit.

Nov 11, 2010 | 2006 Dodge Ram 2500

1 Answer

How do you change the light bulb under the mirror on the drivers sides door?


How do you change a light bulb on the passenger side mirror of a 2006 ford expedition?

May 20, 2010 | 2003 Ford Expedition

1 Answer

Pasenger Turn Signals


did you check ALL the bulbs for ALL the lights?

May 23, 2009 | 1999 Chevrolet Blazer

1 Answer

Replacing burned out turn signal bulb in passenger side mirror.


I'm pretty sure the light is part of the glass. The mirror glass is available seperately. Check Ebay or tascafordparts.com for a discounted part. Or, car-part.com for used one. Page with * is lowest price.

here is 2003 Nav. I don't have 2004. May be similar. please give good rating if this help. Good luck
-----
Removal and Installation
  1. Position the mirror glass to obtain a gap at the top edge of the mirror and carefully pull the top edge of the glass away from the mirror housing.

  1. Disconnect the heated mirror electrical connectors.
47533d6.gif
  1. Remove the exterior mirror motor screws and exterior mirror motor.
    • Disconnect the electrical connectors.
29728ca.gif
  1. To install, reverse the removal procedure.


-------

Mar 29, 2009 | 2004 Lincoln Navigator

1 Answer

Right turn signal not working on 1992 Ford Explorer Truck


turn on the hazard light so you can identify the bulb that is actually deffective. the procedure to replace can be found on youtube.

Mar 10, 2017 | 1992 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...