Question about 1992 Chevrolet C/K 3500

1 Answer

A ned positon cables fron distribuidor to

A ned positon cables fron distribuidor to spark plugs

Posted by on

  • yadayada
    yadayada May 11, 2010

    what engine

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

1 8 4 3 6 5 7 2 firing order

Cylinder 1 it the furthest forward in the engine compartment. That bank is drivers side 1 3 5 7 Passenger side is 2 4 6 8

You did mark #1 when you took it apart right?

If not, remove coil wire from distributor and ground. (IMPORTANT ALWAYS GROUND THE COIL SECONDARY LEAD) remove #1 spark plug. Turn engine over by hand. When you hear the whoosh that's #1 compression stroke. Line up timing mark to 0 Degrees. Remove distributor cap. Wherever the rotor is pointing, that is #1 cylinder. Crank engine to determine direction of travel of rotor (clockwise probably) Next cylinder will be #8 next will be #4 next will be #3 next will be #6 etc. just follow listed firing order.

After repair is complete reconnect coil wire.

Posted on Sep 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4ze1 rodeo amricana


si el sensor de levas o el sensor del siguenal estan danadosno le van a mandar el neutro o la face depende del carro cuando trates de encender checa esos sensores alguno esta fallando

Jan 29, 2014 | Isuzu Amigo Cars & Trucks

1 Answer

Have 1998 mitsubishi mirage with a rough idle i replace spark plugs,map sensor would really appreciate any help thanks


do you the check engine lite on if the answer is yes take your car to the closest autozone to free scanner check. anyway check and clean the injector check the spark plugs wires also check distribuidor cap&rotor check the coil good luck

Aug 25, 2011 | Mitsubishi Mirage Cars & Trucks

1 Answer

Por Que no hay corriente en el cable Que va de la bobina al distribuidor


la computadora controla todo si cuando abres el swicht prende la bomba de gas por 3 segundos cuando la maquina da vueltas el distribuidor tambien dentro del distribuidor tiene un sensor que manda la senal a la bobina dando el tiempo de encendido ..... pero puedes calar primero con otra bobina . suerte

Dec 16, 2010 | 1992 Honda Accord

1 Answer

1987 pontiac fiero spark plug firing order fron distributor to spark plugs


Hi,

The firing order is - 1 2 4 5 6

taran_2005_2.gif

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Nov 26, 2010 | 1986 Pontiac Fiero

1 Answer

NECESITO UN DIAGRAMA DE COMO CONECTAR LOS CABLES DE LAS BUJIAS AL DISTRIBUIDOR DE UN ASTRO 1996


NECESITO UN DIAGRAMA DE COMO CONECTAR LOS CABLES DE LAS BUJIAS AL DISTRIBUIDOR DE UN ASTRO 1995

Jun 15, 2010 | 1996 Chevrolet Astro

1 Answer

Truck will start but not continue to run after starter is disengaged. I replaced the distributer cap, rotor, electronic ignition modul. It is getting air and fuel. have a good spark at spark plugs during...


check the power at distributor with the key to the on positon with engine off. it should have 12v. if there's no voltage, try cranking it and if you get power, then it may be your ignition switch.

Feb 18, 2010 | 1985 Dodge Pickup 4WD

2 Answers

Car won't start wet


good start would be spark plug wires

Feb 05, 2010 | 1994 Dodge Caravan

1 Answer

Mi 95 civic se ahoga en gas y no quiere prender


revisa si las bujias estan tirando la chispa con un "spark tester" o quita una bujia y dejala conectada al alambre, luego pon a alguien mas a qe le de marcha sin prender el carro mientras tu ponle atencion a la bujia, fijate si tira chispa haz lo mismo de una por una(solo de una a la vez, saca una y regresala cuando ya revisaste si tira la chispa) si ninguna tira chispa entonses es tu distribuidor, te recomiendo el "spark tester" por que ba entre el alambre y la bujia y si la bujia no sirve en la bujia no bas a tener chispa pero en el "Spark tester" si. si si es el distribuidor revisa la cubierta y la pastilla pero a ese punto es mejor cambiar todo el distribuidor. espero que esto te ayude. o y recuerda lo principal para que ensienda Gas, Aire y chispa revisa esos tres si todos estan vien va ha prender.

Dec 24, 2009 | 1995 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...