Question about 1994 Ford Probe

1 Answer

How to change stud in rear wheel hub assembly. i need to know how to change the stud in the rear wheel hub assembly, and how do i go about taking it apart

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

Remove tire and wheel, remove caliper and brake rotor. DO NOT apply the brakes while the caliper is loose. Hit stud you want to replace hard with a LARGE HEAVY hammer to drive it out towards vehicle. DO NOT use a light hammer. It will distort the stud and possibly mushroom the end making it very difficult to remove. Once the stud is loose, you may or may not have enough room to get it out of the hole. You may need to pull the hub loose from the rear suspension to gain more room. Remove the stud. Place new stud in hole. Put a stack of washers over the stud, grease the threads, and using a new FLAT nut with the same threads as the lug nut, tighten until the stud is pulled all the way into the hub. Remove the flat nut, reattach the hub assembly (if you needed to take it loose) and reinstall the brakes.


Posted on Sep 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I replace all five lug nuts on front driver side wheel?


They are pressed in from the backside of the wheel hub that the studs stick out from. And not like needing a heavy press- once you get the old studs driven out (usually works with a hammer or small mallet), you can easily draw the new studs right into a snug fit by using the lug nuts, the new ones you just bought along with the 5 new studs, available at most any parts store.

See it's not the lug nuts that are broken, those nuts tighten the tire to the hub by the lug nut studs that the tire fits over. It is the studs themselves that are breaking off. This is common enough that parts stores carry replacements. A chevy dealership might have just your size in stock, if you don't mind paying extra high dealership charges, but it might not be that much for these rather inexpensive items. In a lot of cases, the studs can be removed from the hub as it sits, but there are cases where the hub must be removed from the vehicle for stud replacement. You can eyeball it and pretty much tell if the studs can be removed easily, after you take the wheel (tire) off. For any work on the vehicle, don't rely on the jack. Use blocks or jack-stands always.

Oct 25, 2015 | 2000 GMC Jimmy

2 Answers

How to replace rear wheel studs on a 2008 Chrysler Aspen?


  • Sounds like the axles have to be pulled to get the studs out. Not that familiar with Aspens but if it wont clear the backing plate the hub assembly has to move out away from it.

May 16, 2014 | 2008 Chrysler Aspen

1 Answer

Rear bearing


Remove the rear wheel, if the vehicle has rear disc brakes remove the brake caliper and brake rotor, If the vehicle has drum brakes , slide the drum off. Remove the 4 hub mounting bolts located on the back side of the backing plate.Using a hammer tap on the hub assembly (near the wheel studs) Reverse the steps to install the new hub assembly.

Jun 11, 2013 | Cars & Trucks

1 Answer

Change a front wheel stud on a freelander


You need to take the entire wheel assembly off. The wheel stud will need to be pressed out of the hub and a new one pressed in.

Oct 14, 2012 | Cars & Trucks

1 Answer

How do I replace a broken lug nut out of 98 windstar?


you don`t say if its front or rear lug nut(assuming you mean stud).remove the wheel and then the drum or rotor,then take a hammer and hit the broken stud to remove it from the hub assembly.with the correct wheel stud insert it through the hole and make sure its in straight,install the wheel nut and tighten the nut to pull the stud into the hub until all the way in.you may have to install washer on the stud and re-install the nut and tighten until the stud is seated all the way.

Sep 16, 2011 | 1998 Ford Windstar

1 Answer

Can you tell me if it takes special tools to remove the rear brake hub and brake line


No, there are no special tools required beyond everyday hand tools.

Raise the vehicle.
Remove the rear wheel and tire assembly from the vehicle If the vehicle is equipped with rear drum brakes, remove any retainer clips from the wheel mounting studs, then pull the brake drum off the hub and bearing.
If the vehicle is equipped with rear disc brakes perform the following:
Remove the two guide pin bolts securing the front disc brake caliper to the steering knuckle.
Remove the disc brake caliper from the knuckle and brake rotor.
Hang the caliper out of the way using a wire hanger or cord. Do not support the caliper by letting it hang by the hydraulic hose.
Remove any retainer clips from the wheel mounting studs, then pull the brake rotor off the hub and bearing.
Remove the dust cap from the hub and bearing assembly
Remove the retaining nut, then the hub and bearing from the knuckle's spindle

Oct 10, 2010 | 2004 Dodge Neon

1 Answer

How do u fix a rear stud on a 1999 Nissan Maxima


You will need to remove the Rear Wheel, Brake Caliper, and Rotor to replace the Stud. Once those are removed, take a Hammer and hit the Wheel Stud from the front to drive the Stud out through the back of the Wheel Hub. Once the Stud is out, take the new Stud and insert it in the Hub from the back. You will need to get a Open Ended Nut with the proper thread size as the Stud and thread it on the Stud, and tighten the Nut till the Stud comes all the way through the hole and the end of the Stud is flush with the back of the Hub. Remove the Nut and you can now put everything back together.

Jul 15, 2010 | 1999 Nissan Maxima

1 Answer

How do I replace the studs on the rear wheel


remove wheel and brake assembly, drive broken stud through back off the hub. Put new stud through hole and use a spacer and an old lug nut to pull stud till its seated in hub.

Feb 27, 2010 | 1993 GMC Suburban

2 Answers

Broken wheel studs on 1996 grand am se- passenger front


usually they are an assembly but when i get crazy and damage studs i raise and support both front wheels so i can turn them and slowly move the hub where you can fit teh stud in and use an open lugnut to tighten down it will pull the stud in (i use an air compressor for this)

Apr 28, 2009 | 1996 Pontiac Grand Am

1 Answer

Wheel Stud


If you remove the wheel drum you can knock out the broken stud. It is pressed into the hub. Take the hub to aan auto parts store ( so you get the same size stud) and buy a new stud. put the stud into the hole in the hub. When you remount you remount the tire and tighten the lug nuts that will pull the new stud up tight in the hub.


Hope this helps

Good luck Loringh

Oct 18, 2008 | 1996 Kia Sephia

Not finding what you are looking for?
1994 Ford Probe Logo

530 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5626 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...