Question about 2006 Jeep Commander

1 Answer

With the key turned to the on position and engine not running the check engine light flashes 11 times. this is for a 2006 jeep commander 3.7. the check engine light does not come on when the engine is running. do i have a problem or no?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

A logged cod may have been stord on the system check service manual or dealer to id fault if any

Posted on Sep 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2006 jeep commander makes a clicking noise when I turn ignition, all lights and radio come on but car won't turnover, what is it?


I have had this issue 2 times, both times it was the battery having damaged/dead cells. You can sometimes get it to start by putting your foot on the break, turning the key to the on position, putting the car in neutral then starting it. I purchased my Commander new in 2006 and have had to replace the battery 2 times since, both times this was the initial symptom. I have 120K miles and still love my Commander

Mar 06, 2011 | 2006 Jeep Commander

3 Answers

I changed my spark plugs and afterwards the chech engine light came on. the jeep runs great. what can make that happen?


IT could be something such as a loose plug wire.The best advise I can give you is to take your jeep to your local auto parts store and have them pull the codes out of your on board computer.This will give you an area that you can concentrate on to make the necessary repairs to get your check engine light to go out.

Feb 21, 2011 | 2006 Jeep Commander

1 Answer

My 94 jeep loaps and then backfires out the tail pipe can you solve


Power train control module controls the drivetrain. If you can get a code from the computer it would go a long way diagnosing wether its an engine malfunction or computer issue. To get the codes bring a pen & piece of paper out to the car, turn the key to the run position (not start but when all the dash lights come on) then off then run then off then run (three times in the on position, after you have turned the ke on then off 3 times on then leave the key in the on position and watch the check engine light. It will flash a code to you for example check engine light turns on then off 1 time with a long pause then the light flashes three times then another pause this would be the #13 code , most start with this code to tell you that it is checking codes. Just count the # of flashes (from the check engine light) & that is the first # of the code it will pause then flash again & that is the second # of the code. Flash 5 times pause then 5 more flashes is the # 55, & that is the last code you get to indicate all codes have been displayed, so key on then off then on then off then on & watch the check engine light count the flashes write down that # when it pauses then count the next number of flashes until the pause & that is your trouble cod they are 2 # codes & usually 13 is the first code flashed & the # 55 is the code that lets you know it is done, all the 2 digit codes in between are trouble codes & can be found in a chiltons or haynes service manual or search the web for chrysler trouble or computer codes.

Sep 23, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

2000 jeep cherokee sport...can I check the engine codes by cycling ignition switch?


if so just turn the key to run position ( not start) then one click back. Do this a total of 3 times ending in the run ( or on; not start) position. The odometer will display the code(s) or in an older model the check engine light will flash out the code. Have your pen and paper ready to jot down the results.

Aug 23, 2010 | 2000 Jeep Grand Cherokee

1 Answer

WHAT DOES PREFORM SERVICE MEAN ON THE 2006 JEEP COMMANDER


this light is programed to come on from the factory, i think its every 7,500 miles to remind you to change the oil and also there maintinance book lists things to do every 7500 miles most of it is wasted $$$.as long as you change your oil and prefrom your 30,000 mile services dont worry about that light, this is how to reset the light.1. turn key on engine not running 2. fully press gas pedal to floor 3 times with in 10 seconds of turning key on, 3. turn key off 4. your all done. HOPE THIS HELPS.

Feb 11, 2010 | 2006 Jeep Commander

3 Answers

2006 Jeep Commander Intermittent Starting Problems


Common problem in snow country where salt water can corrode starter parking gate wire connection at started tab. Just cleanthe connector and tab, coat in dielectric grease, problem solved in 15 minutes!

Sep 12, 2009 | 2006 Jeep Commander

4 Answers

2007 Jeep Commander will not start


Check the battery cables, then go to the starter relay, then the starter, (If the lights are bright when you turn them on)

Aug 01, 2009 | 2007 Jeep Commander Rocky Mountain

2 Answers

2002 Jeep Wrangler 4.0 When Driving the Engine Dies


Put the key in the ignition and turn it on and off (3) times without starting the jeep, leaving it in the on position count the (1) flashing indicator Light, Eg: (5) flashes, Then there will be a pause, then it may flash (3) times, this is a code #53. Keep your Eye on them and write them down. If you should miss (1) Repeat as many times as needed, Info: A #55 means there are no codes!!

May 30, 2009 | 2002 Jeep Wrangler

1 Answer

Possible causes for suddenly having no spark on 94 jeep cherokee


There are several reasons this can happen, the most common is that the crankshaft sensor has failed. This should give a code of 11. I recommend that you do a code check, in order to get an idea of what problems may be before doing anything else.
Code check: turn ignition key of and on twice, then the third time leave it in run position. check engine light will falsh. one flash pause, next flash(s), longer pause, then next set of falshes. If just crank sensor you will get firss code of 11, then next set will be 55 (end code)
If you find this somewhat helpful, don't forget to rate it! Need further info? I'm here!!

Mar 24, 2009 | 1994 Jeep Cherokee Country

1 Answer

Check enggine


Do a self test. Turn key to on position and back to off position 3 times. a series of flashes will commence from the "check engine" light. The first set of flashes is the 1st digit of the code, then there will be a pause, then a 2nd set of flashes, This will be the 2nd digit of the code. For example, 3 flashes, pause, 7 flashes, means code 37. Check what the code means in a Haynes auto repair manual. This will tell you what the engine light on your car means.

Jun 12, 2008 | 1998 Jeep Cherokee

Not finding what you are looking for?
2006 Jeep Commander Logo

308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...