Question about 2003 Toyota Highlander

Open Question

Need to replace parking lamp - 2003 Toyota Highlander

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chevy equinox, running lights are not working, fusses work fine, what else would be the problem?


The problem is your not familiar with electronic's on modern automobiles . Module controlled systems . BCM - body control modules .
The park lamps consist of the park, tail, marker and license lamps. These lamps are illuminated any time the headlamp switch is in the PARK, ON position, or anytime the body control module (BCM) illuminates the headlamps. The PARK fuse in the fuse block - instrument panel (I/P) supplies voltage to both the coil and switch input side of the park lamp relay. The BCM controls the park lamp relay by grounding the park lamp control circuit energizing the relay.

PCB Relays
This vehicle is equipped with the following PCB mounted relays. High Beam, Low Beam, DRL, Fog Lamp, Park Lamp, Stop Lamp, and Horn relay. They are directly soldered to the underhood fuseblock circuit board. A failure of one of these relays will require the whole underhood fuseblock to be replaced.

Your best bet have a qualified repair shop diagnose the problem . Could have DTC'S - diagnostic trouble codes stored in the BCM For circuit faults .
Park Lamp Switch On
B257A 00
B2057A 00
B257A 00
--
When the headlamp switch is in the OFF position, the body control module (BCM) receives a ground signal through the headlamp switch OFF circuit and an open signal on the park lamp ON circuit. When the headlamp switch is in the PARK or HEAD position, the BCM receives an open signal through the headlamp switch OFF circuit and a ground signal through the park lamp ON circuit.

DTC B2585 00: Park Lamp Control Circuit - Domestic

Jan 17, 2017 | 2007 Chevrolet Equinox

1 Answer

Tail lights not working fuse is good bulbs are good. What do I need to check now. 2008 Pontiac G6


What fuse is good ? Did you check fuse in rear fuse box ? Also did you check park lamp relay .
Park, Tail and Marker Lamps
The park, tail, and marker lamps, including the license lamps, are turned ON when the headlamp switch is placed in the PARK or HEADLAMP position, or anytime the headlights are requested. The PARK LAMPS fuse in the rear fuse block supplies battery positive voltage to the PARK LAMP relay switch contacts. The PARK LAMPS fuse in the rear fuse block also supplies battery positive voltage to the PARK LAMP relay coil. When the park lamps are turned ON, the body control module (BCM) energizes the park lamp relay. Current flow is from the PARK LAMP relay to their respective park and marker lamps and to ground. Ground is provided at G101, G102, G401, and G403.
Fuse Block - Rear
Left side of the rear compartment, behind the left rear wheel well

Jan 08, 2017 | Pontiac Cars & Trucks

2 Answers

I have a 2007 Chevy HHR..the tail light don't work the bulbs workI have turn signals and brake lights..no owners manual in car. check fuses can't locate the fuse for tail light is there another place


Your talking about the rear park lamps, but, do the front park lamps work?
Note the picture.
Underhood fuse box, 68 is park lamp relay, 69 is park lamp fuse.
26139691-ogmtu0xiyqttvnd1jjcu4dmt-2-0.jpg

Mar 23, 2016 | Cars & Trucks

1 Answer

Why aren't parking lights working?


Park lamp fuse 20amp located in the under hood fuse box .DRL control module
Daytime Running Lamps (DRL) Control Module
Right of the steering column, behind the IP
Park, Sidemarker, Tail and License Lamps
Voltage is applied continuously to the PARK fuse to the headlamp and the instrument panel (IP) lamp dimmer switch through CKT 1340.
When the headlamp and the (IP) lamp dimmer switch is in the PARK or HEAD position, voltage is applied to CKT 9 thus activating the following lamps:
• The park lamps
• The side marker lamps
• The tail lamps
• The license lamps
The park/turn lamps are the only lamps that do not activate yet receive a current from CKT 9. The park/turn lamps do not activate because the voltage drop across the front side marker lamps is much higher than that across the turn lamp filaments Step
Action
Normal Result(s)
Abnormal Result(s)*

1
Turn the headlamp/instrument panel (IP) lamp dimmer switch to the PARK position.
The following lamps light:
• The license plate lamps
• The taillight lamps
• The front side marker lamps (Domestic)
• The front parking lamps (Domestic)
The headlamp position lamps (Export)
Refer to Park Lamps Inoperative
Park Lamps Inoperative
Step
Action
Value(s)
Yes
No

1
Inspect the PARK LP fuse.
Is the fuse open?
--
YES - Go to Step 2
NO - Go to Step 3

2
Repair a short to ground in CKT 1340.
Is the repair complete?
--
Go to Exterior Lights System Check
--

3
Turn the headlamp/instrument panel (IP) lamp dimmer switch to the PARK position.
Use a test light in order to backprobe the headlamp/IP lamp dimmer switch harness connector between terminal R and ground.
Did the test lamp light?
--
Go to Step 7
Go to Step 4

4
Use a test light in order to backprobe the headlamp/IP lamp dimmer switch harness connector between terminal O and ground.
Did the test lamp light?
--
Go to Step 5
Go to Step 6

5
Replace the headlamp/IP lamp dimmer switch. Refer to Headlamp Switch Replacement .
Is the repair complete?
--
Go to Exterior Lights System Check
--

6
Repair the following conditions in CKT 1340 between the PARK LP fuse and the headlamp and the IP lamp dimmer switch harness connector terminal O:
• A faulty connection
• An open circuit
Is the repair complete?
--
Go to Exterior Lights System Check
--

7
Repair the following conditions in CKT 9 between the headlamp and the IP lamp dimmer switch harness connector terminal R and S204:
• A faulty connection
• An open circuit
Is the repair complete?
--
Go to Exterior Lights System Check

Feb 18, 2016 | 1999 Pontiac Montana

1 Answer

I have a jeep liberty 2005 2 wheel drive my passenger side driving light will not come on. Also instrument panel lights will not come on either.


first off ,you did electric work and skipped step 1
pull battery neg lug first.
so you blew the fuses.
what IP lights. all warning lamps.
or just the park lamps in the cluster.
part is called Illumination in said cluster.

where is these other lights, what is a driving light, (park, head,turn, what? brakes?)
tell all lights that work & not , inside and outside car.
tell what knob you turn. can be like 10x better clue...?????
burned sockets are shorted lamps, the brass base lamps love to short inside, (china made x10) get new ones from top maker....

ok, so after replacing the TL assy.
what dont work now, report all lamps.
if it's only outside lamps failing, say so..
i guess you dont know that parking lamps go to like 20+ places, inside and outside car. so. parking lamps are special if acting up
then brake lamps
then blinkers (turn signals)
then reverse.

if the parks (aka, incorrectly TAIL) are bad, then we need to know that. using the correct word.
parks are on all 4 counters, and side lights and inside car.
that is why tail lamp , is a bad name. but fuses are marked as tail on many cars.

also when working on car external lighting
make sure no trailer towing hacks are found.
look for non OEM hack jobs, at the rear corners. Uhual hacks.
or past collision damage to wiring not repaired properly.

how is that>?

Jun 21, 2015 | 2005 Jeep Liberty Sport

1 Answer

How do i replace the PK Lamp fuse


In the instrument panel fuse block is a fuse marked PK LAMPS the fuse directly above is a 10 amp fuse ,this is the one you want to check. There is also a relay involved in making the park lights work and the Body control module .The relay is in the same fuse block as the PK LAMP fuse, marked PK LP . Not to sound like I'm talking down to you but do you know what a relay looks like ? The fuse block is Right side of the I/P, behind the access panel. Open the passenger door , at end of the Dash is a panel ,pull it off ,then you'll see fuse box .On the inside of the panel it tells what each fuse and relay is. I'm going add how the park lights work description.
The PARK LAMPS fuse in the instrument panel (I/P) fuse block applies battery positive voltage to both the coil and switch side of the PARK LAMP relay in the I/P fuse block. When the headlamp switch is placed in either the PARK or HEAD position, ground is applied from G202 to the headlamp switch. The headlamp switch then applies the ground through the park lamp switch ON signal circuit to the body control module (BCM). The BCM then applies a ground to the PARK LAMP relay enable circuit. This energizes the PARK LAMP relay, applying battery positive voltage to all the park, tail, marker and license lamps. The park, tail, marker and license lamps are also turned ON when the headlamps are commanded ON by the BCM for low light operation. Good luck !

Dec 23, 2014 | 2005 Pontiac Grand Prix

3 Answers

Why the brake light works and tail light don't work Chevrolet avalanche 2003


they are dual filament bulbs so the tail light filament might have blown and not the stop light , replace the bulb to check

Jul 18, 2014 | 2003 Chevrolet Avalanche

1 Answer

2001 Monte Carlo SS 3.8 v6 Rear park lights are out as well as the dash lights, brake lights work headlights work front running and park lights work, all turn signal lights work. replaced headlight switch...


Park, Tail, Marker Lamps, and License
The park, tail and marker lamps, including the license lamps, turn on when the headlamp switch is placed in either the PARK or the HEAD position, or anytime the headlamps are requested. The RT I/P #1 fuse in the RH I/P fuse block supplies battery positive voltage to both the park lamp relay switch contacts and to the park lamp relay coil circuit. The park lamp relay coil is controlled by the body control module (BCM). When the headlamp switch is placed in the PARK position, the BCM energizes the park lamp relay coil control circuit.
Current flows from the park lamp relay switch to both front and rear park lamp fuses and to their respective park/tail lamps. The front park lamps are grounded at G101. The rear park lamps are grounded at G302. The license plate lamps are a part of the rear park lamp circuit and are grounded at G302. The inadvertent power control feature prevents the park lamps from remaining on more than 10 minutes if left on. If the park lamps are turned on after the ignition switch has been turned OFF, or is in the ACCY position, they will remain on until turned off or until the battery runs dead.

Did you the REAR PARK LP fuse 15 amp in the right insturment panel fuse box.

Jul 18, 2017 | 2001 Chevrolet Monte Carlo

1 Answer

Tag light is not working. is there a fuse that will get the light turned back on?


The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:
  1. Remove the two mounting screws from the license plate lamp.
  2. Remove the license plate lamp from the rear bumper fascia.
  3. Remove the license plate lamp socket by turning it counterclockwise.
To Install:
  1. Install the license plate lamp socket by turning it clockwise.
  2. Position the license plate lamp to the rear bumper fascia.
  3. Install the license plate lamp mounting screws.

Feb 17, 2011 | 2004 Chevrolet Impala

1 Answer

I need diagrams for the fuse boxes in the dash and engine compartment so I can find the fuse/relay I need to replace. My dash lights, tail lights and windsheild wipers are out.


Hi
There are a couple of wiring diagram and manual available on the net. The relay you are talking about is the park lamp relay which supplies power to the tail lamps, license plate lights and both front and rear park lamps. If the park and plate lights are working the light switch, relay and supply power are good. You need to verify for a broken brown wire to the tail lamps (assuming the sockets, lamps and grounds on both tail lights are good) .If none of the lamps are working then the 15A fuse number 3, the light switch or the park lamp relay could be bad (note different contact in the main light switch work the other lights)

You can find a wiring diagram and component location at
www.autozone.com and http://www.pdfgeni.com/book/1998-ford-ranger-wiring-diagram-pdf.html


Let us know if you want something more else accept the solution.
Thanks for contacting fixya.com

May 23, 2010 | 1999 Ford Ranger SuperCab

Not finding what you are looking for?
2003 Toyota Highlander Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...