Question about 1998 Chevrolet Venture Cargo

Open Question

How to remove an ignition switch from 1998 chevy ventrue

Posted by on

  • Stanley Kramer May 11, 2010

    The actual electrical switch or the key switch in the steering column

  • yadayada
    yadayada May 11, 2010

    do u mean the key cylinder?

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 chevy cavalier starts and runs great but when you put it in gear the warning lights come on in the dash and it dings like the door is open, and it stays like that till you shut the car off.


Try this,it wont cost anything but time.Remove the ignition switch(not the key lock) But leave it plugged in. Place the key lock in the run position. Using a screw driver turn the ignition switch and start the car. Does it still ding? It Should... If yes, push in the little white stem on the key lock with your finger.(on the tip BETWEEN where it was connected to the wired ignition switch) Does it stop? If yes, either the little stem has worn down or a dent has worn into the plastic electrical ignition switch. You will have to decide which is not right. But that is the part that sets off the "Key Left In Car" ding.

Apr 02, 2017 | 1998 Chevrolet Cavalier

1 Answer

Turn switch


This car is very easy...Take the steering column plastic covers off and un-screw the switch and connector. The upper plastic cover on the column has a tiny screw from underneath that needs to be removed. It's a star head screw, I think a 4mm socket will get, maybe smaller. If I recall the screws that hold the switch in are torx. One of the screws is a pain due to tight space, I used a torx bit and an very small ignition wrench to turn it. But all in all, your lucky you don't have to deal with 3' of wiring harnesses to unhook and undo like some Chevy's.

Jan 28, 2014 | 1998 Ford Taurus

1 Answer

My 1998 Chevy Ventrue driver side window goes up crooked.


THE WINDOW IS OFF THE TRACK.THIS INVOLES REMOVING THE DOOR PANEL TO GET TO THE TRACK . UNLESS YOU ARE VERY MSURE OF WHAT YOU ARE DOING I SUGGEST YOU SEE YOUR REPUTABLE AUTO TECH .THE SPRING ON THE REGULATOR IS UNDER PRESSURE AND IF YOU ARE NOT CAREFUL YOU COULD INJURE YOURSELF. THIS IS NOT A NOVICE REPAIR HOPE THIS HELPS BILL

Dec 11, 2012 | Cars & Trucks

1 Answer

How do i replace a ignition switch on a 1998 chevy blazer


To get exact procedure with diagram and detail.Please click on the link below and follow the instructions to replace ignition switch on 1998 chevy blazer.Click the link below:--- http://technoanswers.blogspot.com/2011/02/how-to-replace-ignition-switch-on-1998.html ------------- This should help.Thanks.Helpmech.

Feb 25, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

I have a chevy 1988 S 10 The keys are lost and I'd like to replace the ignition key cylinder. How do you remove the old cylinder & install a new one ?


take the sterring wheel off get this horse shoe looking tool to press the in plate take the snap ring off 4 screws holding the turn signal switch in then you will need a t15 or t20 pull that screw out which holds the ignition switch in

Jan 29, 2011 | 1998 Chevrolet S-10 Pickup

1 Answer

My 1998 chevy truck ignition stuck I took the steering wheel off


You need a lock plate removal tool,napa sells them ,they are cheap,and the pin in the key cylinder? Use a punch to destroy the pin.

Jul 21, 2010 | 1998 Chevrolet K1500

1 Answer

The passenger side power window will not roll back up no my 2001 chevy ventrue all other windows and lights are working fine.


Make sure you have voltage going to the switch. Then make sure you have voltage going to the motor in the door. If you have voltage in both place you will need to replace the window lift motor.

May 17, 2010 | 2001 Chevrolet Venture

3 Answers

Where does the flasher go on a 98 chevy malibu


Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
  1. Remove the bezel from the ignition switch.
7f58edd.gif
Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.

9f5c3cc.gif
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .

bd28884.gif
. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.

daa6205.gif
Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.

c506713.gif
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

Dec 01, 2009 | 1998 Chevrolet Malibu

1 Answer

Ignition switch


You would be better off to go to a parts store and get a haynes manual for that. It's way too much to explain on here.

Jan 27, 2009 | 1998 Chevrolet Malibu

1 Answer

Electrical Short - 1998 Chevy S-10


i had the same problem it was the ignition switch, somehow didi not close all the way

Oct 25, 2008 | 1998 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...