Question about 1998 Jeep Grand Cherokee

Open Question

Interior rattle on passenger side right rear quarter panel. Right behind the seat back. How do I fix it?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing quarter glass on left side on 2005 pontiac gto


Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Dec 23, 2016 | Pontiac Cars & Trucks

1 Answer

Can't find the interior fuse box on a Cadillac CTS 07...looked under the back seat not there.


This Cadillac factory service info . Doesn't lie ! your vehicle has four fuse boxes !
Fuse Block - Left Rear
In the passenger compartment, under the left side of the rear seat at carpet
Power and Grounding Component Views
Electrical Center Identification Views
Fuse Block - Right Rear
In the passenger compartment, under the right side of the rear seat at carpet
Power and Grounding Component Views
Electrical Center Identification Views
Fuse Block - Steering Column
In the passenger compartment, behind the driver knee bolster, at the base of the steering column near C202
--
Electrical Center Identification Views
Fuse Block - Underhood
In the engine compartment, in the right front corner

Aug 23, 2016 | Cadillac Cars & Trucks

1 Answer

2006 Tahoe. Where is the auxiliary blower motor located?


It is located behind the right rear quarter panel , In the back right of the interior !
Remove the right rear quarter trim panel. Refer to Rear Quarter Trim Panel Replacement - Right Side in Interior Trim.
Removal Procedure
  1. Remove the rear seat. Refer to Rear Number 2 Seat Replacement or Rear Number 2 50-50 Seat Replacement in Seats.
  2. Remove the Third Pillar trim panel. Refer to Third Pillar Trim Replacement .
  3. Remove the garnish molding. Refer to Body Rear Corner Garnish Molding Replacement .
  4. Remove the door sill plate. Refer to Liftgate Door Sill Plate Replacement .
  5. Remove the quarter panel trim screws.
A lot involved in this but not to difficult !
  1. Remove the rear door sill trim plate. Refer to Front Side Door Sill Plate Replacement or to Rear Side Door Sill Plate Replacement .
  2. Remove the lower rear seat belt cover and bolt.
  3. Remove the trim panel from the vehicle.
Remove the sill plate. Firmly pull the sill plate up and out from the retainers.
Remove the sill plate from the vehicle. Start from the front of the door sill. Use a flat-bladed tool in order to pry the door sill plate.
Rear Side Door Sill Trim Plate Replacement
Use a flat-bladed tool in order to pry the door sill plate. Remove the sill plate from the vehicle.
Body Rear Corner Garnish Molding Replacement
Remove the rear upper garnish molding. Refer to Rear Upper Garnish Molding Replacement .
Pull down on the upper corners of the garnish molding in order to disengage the retaining clips. Pull in order to disengage the remaining retaining clips. Remove the rear corner garnish molding from the vehicle. Inspect the rear corner garnish molding for broken or missing retaining clips. Replace the retaining clips as needed.
Good Luck ! Fun job !!!!!

Jun 07, 2015 | 2006 Chevrolet Tahoe

1 Answer

Location of temperature blend door actuator on 2005 ford expedition


Are you looking for the front or rear? The front is behind the glove compartment on the passenger side. The rear one is on the passenger side to the right of the rear third row seat behind the plastic panel.

Oct 19, 2014 | 2005 Ford Expedition

1 Answer

Interior access to grand am rear Qrtr Panel


you may have to buy an articulating cable ( the kind with the 3 prongs that move in and out to grab things ) to reach in and grab your object. The quarter panel and the inner metal structure aren't designed to come apart. The only other access you might get would be via removal of the back seat. Usually pushing in on the bottom of the lower part of the seat with unhook it and allow you to remove it to access the 2 bolts that hold the upper part of the seat in place. With that removed, you might have a better angle to grab onto it.

Mar 06, 2014 | Pontiac Cars & Trucks

1 Answer

I have checked all fuses and there good radio is on but no sound . there is what appears to be an amp under rear passenger seat but its just a box not like the old school im used to dealing with


The silver box you're seeing under the right middle row passenger seat is the onstar VCIM, not the amp. If your vehicle has an amplifier for the audio system, it will be: behind the right rear quarter panel (in the cargo area) on a regular wheel base trailblazer, or behind the left rear quarter panel (in the cargo area) on a trailblazer XL.

Oct 19, 2013 | 2007 Chevrolet Blazer

1 Answer

How to replace rear blend door actuator on 97 town and country


Hi Jim, I'm glad to help!

Jim, first you'll need to get the seats out of the way. Next remove the rear quarter panel. The blend door motor will be right in front of you mounted on the side of the Rear A/C Housing. It's been known to go bad. BUT, sometimes the door itself breaks, so you'll need to check that. But most importantly you'll need to make sure it's getting power and ground from the control unit because I have found is some cases it's not receiving power and ground to the motor. You can check the motor by applying power and ground from the battery to see if the motor is good. Hope this helps and have an awesome day Jim.

Jul 12, 2013 | Cars & Trucks

1 Answer

Where is the factory amplifier on gmc envoy 2003


For the XL - The AMP is located on the drivers side, behind the left rear trim panel.

1. Remove the cargo shelf. 2. Tumble the third row seats to the cargo position. 3. Remove the left body side window rear garnish molding.4. 4. Remove the left body side window forward garnish molding. 5. Remove the liftgate sill plate. 6. Remove the left rear door sill panel. 7. Remove the lower seat belt anchor bolt. 8. Remove the auxiliary power outlet from the trim panel. Release the five screws that retain the rear quarter trim panel to the body. 9. Remove the rear quarter trim panel from the vehicle.

If you don't have the XL then the AMP is located on the passenger side.
1. Remove the screw that retains the trim panel to the body. 2. Remove the cargo net retaining knobs. 3. Remove the bolt that retains the seat belt upper guide to the body. 4. Remove the rear upper quarter trim panel from the vehicle. 5. Remove the cargo shade/cover. 6. Remove the inflator access panel. 7. Remove the right rear quarter upper trim panel. 8. Remove the liftgate sill plate. 9. Remove the right rear door sill panel. 10. Remove the lower seat belt anchor bolt. 11. Release the retaining clips that retain the trim panel to the body. 12. Partially remove the trim panel in order to remove the inflator switch from the inflator bezel. 13. Remove the auxiliary air outlet washer and retaining nut. 14. Feed the auxiliary air outlet through the inflator bezel. 15. Remove the inflator bezel from the trim panel. 16. Disconnect the the 12-volt power supply electrical connector. 17. Remove the 12-volt power supply. . 18. Remove the trim panel from the vehicle. 19. Disconnect the electrical connectors from the radio speaker amplifier. 20. Remove the 4 bolts that retain the radio speaker amplifier to the body. 21. Remove the radio speaker amplifier from the body.

Mar 16, 2011 | 2003 GMC Envoy

1 Answer

Where is the blower motor resistor in a 2001 dodge caravan se. I do not see it behind the glove box. I do see soemthing similar under the hood on the passenger side aginst the firewall but it is not...


Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004
Blower Motor - Removal & Installation
  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel.

    a1b7373.jpg
    Fig. The blower motor is located behind the glovebox, behind the blower motor cover
  3. Remove the A/C-heater blower motor cover.
  4. Disconnect the blower motor wiring connector.
  5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  6. Remove the blower motor mounting screws.

    bdc6158.jpg
    Fig. Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

    063bc30.jpg

    Fig. The blower motor is secured to the housing with three small screws
  7. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.


Auxiliary Heater and Air Conditioner
Blower Motor - Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      1dc958e.jpg
      Fig. Removing the trim panel to access the rear blower motor
    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    1e2cfdc.jpg
    Fig. The rear blower motor is held in place by four screws
To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember rated this).

Jul 11, 2010 | 2001 Dodge Grand Caravan

1 Answer

Factory XM Unit Location


Hi Xit.....The factory XM module is in fact located under the rear shelf trim panel. You will have to remove the rear seat cushion, just pull up on the front of the cushion about 12 inches in from left and right corners. Remove the cushion from the car. Open the trunk and remove nuts located on the seat back just under rear shelf metal. Back inside the rear seat area, remove the seat belt buckle bolts located inboard of right and left lower corners of the seat back. Remove the seat back. You will now be able to see the (2) plastic fir tree pins that hold the shelf panel trim in place. Remove the pins.
Now comes the hard part, remove the right and left quarter sail interior trim panels ( Caution: roof rail air bag located behind right and left panels) the fasteners are located behind the "SIR" plastic buttons in the sail panel trim.
All in all, unless you have the proper tools and take the proper precautions, you might want to take your Cadillac to your local dealer.
Buy the way, is there something wrong with your factory XM module?
Let me know, regards.

Feb 05, 2009 | 2006 Cadillac CTS

Not finding what you are looking for?
1998 Jeep Grand Cherokee Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...