Question about 2005 GMC Sierra 2500HD 4WD

1 Answer

Just replaced hub on passenger side only 80k is this normal also have rear axle seal leaking do i have to remove pumpkin cover to pull axle or will it come out with just removing outer bolts

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 142 Answers

Yes this is normal wear, if you have aftermaket wheels and tires the wear will be quicker do to more stress on the bearing, for the rear seal no u do not have to remove the cover if you jack up the side that has the bad seal you dont even have to drain the fluid. the outer bolts hold the axle in. there is no c clip inside the axle to remove

Posted on Sep 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace my inner axle on the passenger side of my 2002 Dodge Ram 4x4 4.7L. I lent my truck out and the C clip let go of the CV axle. The intermediate axle spline is stripped and I need to change...


Lift and support front end on suitable jack stands preferably on frame. Remove right front cv axle, stub shaft, and seal. You will need to pull the right front brake caliper assembly loose and place to the side. Then remove bolts from shock and upper control arm and hub nut to do this. Next, remove axle lock actuator on passenger side of front axle. Place a drain pan underneath front diff cover and remove cover and drain axle. In the center of differential there will be an 8 mm head bolt holding spider gear cross-shaft. Remove bolt and cross-shaft only! Push inner axle in until clip clears inside of passenger spider gear. Set clip aside and push/pull axle shaft straight out to passenger side.

Feb 09, 2015 | Dodge Cars & Trucks

1 Answer

2008 Mercury Mariner rear axle is leaking. Is there a possibility I can just tighten it down or will it require me to replace it?


You have to loosen the rear suspension on that side

Remove the axle nut & pull the knuckle clear of the axle

Then remove the axle on the side that leaks

Change the seal & replace axle,etc.

Jul 08, 2012 | 2008 Mercury Mariner

1 Answer

HOW TO REPLACE PASS SIDE AXEL SEAL LEAKING ON TO BRAKES


you have to pull the axle out. take the pumpkin cover off ,remove the center pin and c-clip pull axle out.

Sep 15, 2010 | Ford E-150 Cars & Trucks

3 Answers

How to replace rear Axle seal on 4x4 chevy


this is very hard if you do not know what you are doing. Ill try to step you through this
  • pull wheels
  • drain pun-kin case
  • pull rear cover
  • in between the spider and axle sets pull C ring with needle nose pliers
  • pull hub and axle out CAREFULLY as there are roller bearings on the end of the axle housing
  • pull seal out at the end of axle housing
  • tap in new seal CAREFULLY and straight DO NOT BEND IT or it will be junk
  • replace axle carefully as the roller bearings are still there
  • replace C clip to original position
  • replace axle diff cover and replace the gasket with a new one
  • refill diff case
  • install tire
  • your good to go

May 03, 2010 | 2002 Chevrolet Silverado

1 Answer

Need detailed manual or assistance in replacing left rear axle seal and bearing on 2005 GMC Sierra pickup with 5.3L engine and a 324 rear end


You'll need to remove the rear end cover, remove the pin in the center pumpkin, push axle toward the center of vehicle and remove the axle clip, pull out axle. You may need a bearing puller to remove bearing.

Mar 04, 2010 | 2005 GMC Sierra

2 Answers

Drivers side rear axle is leaking, not brake fluid, has disc brakes, what do i need to do to replace seal?


i will tell you right off this is a job for a qualified mechanic,the axle has to be pulled off first you jack up that wheel dismantle the brakes and rotor and behind the axle hub are four bolts that hold on the axle remove them and axle will come off the rear end cover does not have to come off and the axle fluid also does not have to come out,but now that axle is out you will notice that a wheel bearing is holding the seal in place this is pressed in you can buy these as a set at the dealer but must be removed by a pro. as not to harm axle and it has to be pressed back in

Feb 06, 2010 | 1995 Jeep Grand Cherokee

1 Answer

1989 chevy van /sportsman 350 v8 leaking rear axell seal wheel side how to pull axlel


Depending on what size your axle is.If you have bolts(6or8) at the very end of the hub.You remove all of the bolts the smack the end of the hub with a hammer to pop out the wedges in the stud holes.If there is just the shaft/plate with studs the you will need to remove the punkin cover and there will be a retainer bolt that holds a 1/2"-3/4" pin.When you get the pin to fall out you will be able to pull the axle shaft out to remove and replace the seal.























Feb 05, 2010 | Chevrolet Sportvan Cars & Trucks

3 Answers

How to change my front differential seal and bearing ? passenger side. I bought a new wheel bearing because of a humming sound on passenger side and doing so saw leaking seal and maybe the humming was...


That will be a Huge job. The whole front diff must come out of the car and the case will need to be taken apart to even gain acess to the carrier side bearings.
The hub bearing is where the wheel bolts up is that maybe what you are talking about?
Also the axle seal isn't that bad to do you need to remove the cv shaft then it's just a simple remove the seal and install the new one.
But all of these jobs will be big ones.

Oct 13, 2009 | 1999 GMC Jimmy

1 Answer

Rear seal and bearing leaking on passenger side.


Basic to get tire and hub off, remove rear diff cover remove bolt, remove clip, pull axle out, then heavy puller to pull bearing and seal. Ck axle for wear

Sep 16, 2009 | 2001 Ford F150 Styleside SuperCrew

1 Answer

I think the front axle seals on my 1999 dodge 3500 4x4 need to be replaced. I am replacing the sealed bearing hubs and I wonder how big of a job it would be to switch out the axle seals inside the...


if you have the hubs of than you dont have much futher to go to replace the axl seals. just slide out the axls the passenger side is two pice then take out the four bolts that hold in the carrier gear then pull out the hole gear asemblie the driver side seal is in the differential housing the passenger seal you have to take of the cad unit in the middle of passenger side axle case.tech article with pictures at pavement sucks.com

Jun 28, 2008 | 1999 Dodge Ram 2500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...