Question about 1990 Cadillac Deville

Open Question

HOW 2 INSTALL A TURN SWITCH IN 1990 CADILLIC

INSTALLING A TURN SWITCH

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starter removal 1990 audi quattro v8


1990 Audi V-8 Quattro 3.6L DOHC

Starter, removing and installing

Disconnect battery NEGATIVE cable
Disconnect wiring from battery to starter and starter to alternator (large terminal)
Disconnect terminal 50 (small wire to ignition/starter switch)
Remove starter mounting screws on engine/transmission
NOTE: Remove upper bolt on starter by guiding 10 mm Allen socket with extension and flex fitting through opening on transmission housing over final drive
Remove starter motor assembly
Reverse procedure to install

Oct 10, 2011 | 1990 Audi V8 Quattro

1 Answer

How to change a ignition switch on a 1990 Z24 cavalier and a diagramof what to look for


Ignition Switch REMOVAL & INSTALLATION 1982–91 Vehicles The switch is located on the steering column and is completely inaccessible without first lowering the steering column. The switch is actuated by a rod and rack assembly. A gear on the end of the lock cylinder engages the toothed upper end of the rod.
  1. Lower the steering column; be sure to properly support it.
  2. Put the switch in the OFF-UNLOCKED position. With the cylinder removed, the rod is in OFF-UNLOCKED position when it is in the next to the uppermost detent.
  3. Unfasten the two switch screws and remove the switch assembly. Fig. 1: Removal and installation of the ignition switch and related steering column components — 1990 vehicle shown 87958059.gif
    Fig. 2: Exploded view of a steering column including the ignition switch — 1990 vehicle with standard column shown 87958060.gif
    Fig. 3: Exploded view of the steering column including the ignition switch — 1990 vehicle with tilt column shown 87958061.gif
    To install:
  4. Before installing, move the new switch slider (standard columns with automatic transaxle) to the extreme left position. Move the switch slider (standard columns with manual transaxle) to the extreme left position. Move the slider (adjustable columns with automatic transaxle) to the extreme right position and then move the slider one detent to the left (off lock). Move the slider (adjustable columns with manual transaxle) to the extreme right position.
  5. Install the activating rod into the switch and assemble the switch on the column. Tighten the mounting screws. Use only the specified screws, since overlength screws could impair the collapsibility of the column.
  6. Reinstall the steering column.

Sep 01, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

How do I change the ignition switch in my 1990


  1. Disconnect battery ground cable.
  2. Place lock cylinder in the Run position.
  3. Remove steering wheel.
  4. Remove turn signal switch. It is not necessary to completely remove the turn signal switch from the column. Pull switch rearward enough to slip it over the end of the shaft. Do not pull the harness out of the column.
  5. Remove attaching screw and lock cylinder set. Do not drop the screw into the column.
  6. To install, align cylinder key with keyway in housing, as shown in Fig. 1. Push the lock completely inward, install attaching screw and torque to 40 inch lbs., on standard columns, or 22 inch lbs., on tilt columns.

Dec 04, 2009 | 1990 Chevrolet K1500

1 Answer

Show diagram of cadillic sls cervintine belt


Its spelt serpentine, and heres a link

http://i153.photobucket.com/albums/s222/hotpotatapie/Serpentinebeltdiagram95Northstar-1.jpg

Sep 08, 2009 | 1996 Cadillac Seville CA Value

2 Answers

1991 cadillac deville fuel problem


fuel pump relay is in engine compartment on drivers side under the flap the two relays that are together ,it is the bottom relay,,u cant by pass.if relay is good ,if it clicks when turning over and key on and off (it should click and go off if key is turned on) then use a test light and ground it find wires going to top of tank and probe wire have some one turn key on ,it should light up test light and go off ,if this happens ,replace fuel pump

Jul 03, 2009 | 1990 Cadillac Deville

2 Answers

Need to change the ignition switch


Remove panel under steering wheel. Put key in cylinder and turn back to accessory position. Looking under lower part of steering column locate a small pin under the key cylinder. While depressing the pin turn the key backwards and pull the entire cylinder with key out of column. Good luck.

Apr 25, 2009 | 1990 Ford Econoline

1 Answer

1990 turn signal switch


it was the turn signal switch thank you very... thank the apprentice for the expert knowledge

Dec 03, 2008 | 2000 Chevrolet Lumina

1 Answer

Replace ignition tumbler


STEP BY STEP Please Remember to Rate Me Thank You RejakWilson




WARNING: On vehicles equipped with Airbags, disable airbag system prior to performing service procedures.



  1. Disconnect battery ground cable.
  2. Remove steering wheel as outlined under STEERING WHEEL procedure.
  3. Using a screwdriver, pry cover from housing.
  4. Using lock plate compressing No. J-23653 or equivalent, compress lock plate, and pry snap ring from groove on shaft, Fig. 5. Slowly release lock plate compressing tool, then remove tool and lock plate from shaft end.
  5. Slide canceling cam and upper bearing preload spring from end of shaft.
  6. Remove turn signal (multi-function) lever.
  7. Remove hazard warning knob retaining screw, button, spring and knob.
  8. Remove pivot arm.
  9. Wrap upper part of electrical connector with tape to prevent snagging of wires during switch removal.
  10. Remove switch retaining screws and pull switch up from column, guiding wire harness through column.
  11. Reverse procedure to install.



  1. Remove turn signal switch as outlined under TURN SIGNAL SWITCH.
  2. Remove buzzer switch and spring clip. On 1990-92 models, ignition key must be removed from lock to remove buzzer switch. On 1991-92 models, switch and spring clip are one assembly.
  3. Turn lock cylinder to Run position on 1989 models or Lock position on 1990-92 models, then remove lock cylinder retaining screw and the lock cylinder.
  4. To install, rotate lock cylinder to the stop while holding housing. Align cylinder key with keyway in housing, then push lock cylinder into housing until fully seated. Lock cylinder must be in Run position to install buzzer switch.
  5. Install lock cylinder retaining screw, then the buzzer switch, turn signal switch and steering wheel.

Aug 30, 2008 | 1989 Chevrolet Celebrity

1 Answer

Installing ignition switch in 1990 chevy pickup


how to replace ignition switch in 1990 chev 1500 pickup long bed

Aug 21, 2008 | 1990 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...