Question about 2003 Ford F350 Super Duty DRW SuperCab

1 Answer

My F-350 has a skip, I put it on the computer it sais that the APP sensor ( the accelerator pedal position sensor) was bad, will this be the cause of the skip, also since I have had this problem my air blows only from the dash not the vents...are they connected?

Posted by on

  • 1 more comment 
  • Anonymous Mar 11, 2014

    system keep saying inactive feature star flash

  • Anonymous Mar 11, 2014

    2002 acura TL slips out of first gear when cold

  • Anonymous Mar 11, 2014

    2002 chevy silverado leaking oil from cooler line bolt

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,741 Answers

No the two problems are different.
yes the bad APP sensor can make the car skip.as the accelerator problem will not give the car to move and so it skips.
-------- there is a vacuum or a linkage problem with the heater control assembly.------
-------------------
this will help.thanks.please do rate the solution.thank you for using fixya.keep updated.

Posted on Sep 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 2010 Chevy impala. Reduced engine power. Service traction control and stability track. and check engine light. Codes are P2138 P2122 P0455


Electronic throttle control !
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit
DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage
DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage
DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit
DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage
DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage
DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

2009 Chevy Silverado P2138 Accelerator Pedal Position


Circuit/System Description
The throttle actuator control (TAC) system uses two accelerator pedal position (APP) sensors to monitor the accelerator pedal position. The APP sensors 1 and 2 are located within the pedal assembly. Each sensor has a 5-volt reference circuit, a low reference circuit, and a signal circuit.
Two processors are also used to monitor the TAC system data. Both processors are located within the engine control module (ECM). Each signal circuit provides both processors with a signal voltage proportional to pedal movement. The processors share and monitor data to verify that the indicated APP calculation is correct.

DTC P0455: Evaporative Emission (EVAP) System Large Leak

The control module tests the evaporative emission (EVAP) system for a large leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge solenoid valve OPEN and the EVAP vent solenoid valve CLOSED. This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge solenoid valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. The following table illustrates the relationship between the ON and OFF states, and the OPEN or CLOSED states of the EVAP canister purge and vent solenoid valves.

Nov 03, 2017 | Cars & Trucks

1 Answer

2006 impala 3.5 LT check engine and service traction control? Code: P2138


DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation
Electronic throttle control problem .
The throttle actuator control (TAC) system delivers improved throttle response and greater reliability and eliminates the need for mechanical cable. The TAC system performs the following functions:
• Accelerator pedal position sensing
• Throttle positioning to meet driver and engine demands
• Throttle position sensing
• Internal diagnostics
• Cruise control functions
• Manage TAC electrical power consumption
The TAC system includes the following components:
• The accelerator pedal position (APP) sensors
• The throttle body assembly
• The engine control module (ECM)

Accelerator Pedal Position (APP) Sensor
The accelerator pedal contains 2 individual accelerator pedal position (APP) sensors within the assembly. The APP sensors 1 and 2 are potentiometer type sensors each with 3 circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
The APP sensors are used to determine the pedal angle. The engine control module (ECM) provides each APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensors provide the ECM with signal voltage proportional to the pedal movement. The APP sensor 1 signal voltage at rest position is less than 1 volt and increases to more than 4 volts as the pedal is actuated. The APP sensor 2 signal voltage at rest position is less than 0.6 volt and increases to more than 2 volts as the pedal is actuated.
Search P2138 on youtube ,will show diagnostic steps .

Aug 19, 2017 | Cars & Trucks

1 Answer

Dtc p0121 throttle position (tp) sensor performance


code p 0121 has to answers
1--refers to throttle position (TP) sensor/accelerator pedal position sensor A--range /performance problem====causes --accelerator cable adjustment--TP/APP sensor ---wiring
The second reference is the same and the causes are--accelerator cable adjustment--TP/APP switch
(APP is accelerator pedal position)

Aug 30, 2016 | Cars & Trucks

1 Answer

I changed everything on a 2007 Chevy uplander the camshaft position sensor And the purged sensor And the throttle body and still the check engine light and the reduce engine power came back on


Reduced Engine Power Mode When the ECM detects a condition with the TAC system, the ECM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
?€¢
Acceleration limiting--The ECM will continue to use the accelerator pedal for throttle control, however, the vehicle acceleration is limited.


?€¢
Limited throttle mode--The ECM will continue to use the accelerator pedal for throttle control, however, the maximum throttle opening is limited.


?€¢
Throttle default mode--The ECM will turn OFF the throttle actuator motor and the throttle will return to the spring loaded default position.


?€¢
Forced idle mode--The ECM will perform the following actions:


-
Limit engine speed to idle by positioning the throttle position, or by controlling the fuel and spark if the throttle is turned OFF


-
Ignore the accelerator pedal input


?€¢
Engine shutdown mode--The ECM will disable fuel and de-energize the throttle actuator.
Did you have it checked for DTC's - diagnostic trouble code's related to the reduced engine power ?
All so has APP sensor gas pedal !
Accelerator Pedal Position (APP) Sensor
The accelerator pedal contains 2 individual accelerator pedal position (APP) sensors within the assembly. The APP sensors 1 and 2 are potentiometer type sensors each with 3 circuits:
?€¢
A 5-volt reference circuit


?€¢
A low reference circuit


?€¢
A signal circuit

The APP sensors are used to determine the pedal angle. The engine control module (ECM) provides each APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensors provide the ECM with signal voltage proportional to the pedal movement. The APP sensor 1 signal voltage at rest position is less than 1 volt and increases to more than 4 volts as the pedal is actuated. The APP sensor 2 signal voltage at rest position is less than 0.6 volt and increases to more than 2 volts as the pedal is actuated.
Your best bet is take your vehicle to the dealer !
al

May 03, 2016 | Cars & Trucks

1 Answer

I have a code P0221,2009 Enclave looking for a good place to start.


code p0221 refers to throttle position sensorB/accelerator pedal position (APP) sensor B--range /performance problem====causes accelerator cable adjustment ( broken)--TP/APP sensor
It also refers tp throttle position switch B/ accelerator pedal position (APP) switch B-range/ performance problem===same cause as before.

Dec 10, 2014 | 2009 Buick Enclave

1 Answer

Check engine light sensor


DTC P2138: Accelerator Pedal Position (APP) Sensor A/B (Throttle Position Sensor D/E) Incorrect Voltage Correlation.

Accelerator pedal position (APP) sensor A and accelerator pedal position (APP) sensor B are potentiometers, and they are installed in the engine compartment.

The APP sensors A and B are operated via the throttle cable to determine the accelerator opening value when the driver presses the accelerator pedal. The accelerator pedal opening value is converted to a signal in APP sensors A and B and transmitted to the engine control module (ECM)/powertrain control module (PCM) to compute the target position. The target position signal is then transmitted to the throttle actuator control module.

APP sensor A is for the primary control, and APP sensor B is a back-up of APP sensor A in case it malfunctions. Both sensors compare their output voltage to each other for malfunction detection.

When the voltage difference of APP sensor B is out of a fixed range for a set period of time, the ECM/PCM detects a malfunction, and a DTC is stored.

Sep 15, 2013 | 2007 Honda Accord Sedan

2 Answers

Reduced engine power, service traction control, service stabilitrak


First of all a scan tool is need for this not a code reader, you need to view scan data after you find what code is stored in the PCM. It could have a problem with the powertrain control module, wiring, or the Accelerator Pedal Position (APP) Sensors. Here are a few codes that could set .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit

DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage

DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage

DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

Oct 02, 2012 | 2008 Chevrolet Tahoe LS

2 Answers

I have these codes coming up on my 2005 Dodge Ram. 5.7 liter motor: P0406 P2096 P0137 P2299 Thank you.


code #0406 = egr position sensor circuit high ( stuck egr valve or bad egr sensor most likely sensor )

code #2096 = downstream fuel trim system lean ( see next code )

code #0137 = O2 sensor bank 1 sensor 2 circuit low ( replace rear O2 sensor driver side )

code #2299 = brake peddle position/accelerator pedal position incompatible. ( hav you been power braking this truck? ) ( brake light was on wile accelerator was being pushed )

Mar 17, 2011 | 2005 Dodge Ram

1 Answer

2003 Yukon Denali XLT lights flicker, rpm goes up and down when on park or stopped or driving and slow speeds. Sometimes it turns off. I thought it might be bad spark plugs or cables so I changed them and...


Your vehicle has electronic throttle control . Position sensor's in the gas pedal an the throttle body , inputs to the Throttle Actuator Control Module
The TAC module is the control center for the throttle actuator control system. The TAC system is self-diagnosing and provides diagnostic information to the PCM through a dedicated serial data line. The TAC achieves throttle positioning by providing a pulse width modulated voltage to the TAC as directed by the PCM.

The throttle actuator control (TAC) system delivers improved throttle response and greater reliability and eliminates the need for mechanical cable. The TAC system performs the following functions:
• Accelerator pedal position sensing
• Throttle positioning to meet driver and engine demands
• Throttle position sensing
• Internal diagnostics
• Cruise control functions
• Manage TAC electrical power consumption
The TAC system components include the following:
• The accelerator pedal position (APP) sensors
• The throttle body assembly
• The throttle actuator control module
• The powertrain control module (PCM)
Accelerator Pedal Position (APP) Sensor
The accelerator pedal assembly contains 2 individual APP sensors within the assembly. The accelerator pedal position (APP) sensors 1 and 2 potentiometer type sensors each with 3 circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
The APP sensors are used to determine the pedal angle. The control module provides each APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensors then provide the control module with signal voltage proportional to pedal movement. APP sensor 1 signal voltage is low at the rest position and increases as the accelerator pedal is applied. APP sensor 2 signal voltage is high at the rest position and decreases as the accelerator is applied.
Throttle Body Assembly
The throttle body assembly consists of the throttle body, the throttle position (TP) sensors, and the throttle actuator motor. The throttle body functions similar to a similar to a conventional throttle body with the following exceptions:
• An electric motor opens and closes the throttle valve.
• The throttle blade is spring loaded in both directions and the default position is slightly open.
• There are 2 individual TP sensors within the throttle body assembly.
The TP sensors 1 and 2 are potentiometer type sensors each with 3 circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
The TP sensors are used to determine the throttle plate angle. The control module provides each TP sensor a 5-volt reference circuit and a low reference circuit. The TP sensors then provide the control module with signal voltage proportional to throttle plate movement. Both TP sensor signal voltages are low at closed throttle and increase as the throttle opens.

Flickering light's could be caused by a bad diode in the alternator . Fluctuating idle could be caused same alternator problem or dirty throttle plate.
Throttle Body Cleaning To Restore Idle Quality

Jul 15, 2017 | 2003 GMC Yukon

1 Answer

I have a 2007 Chevy Tahoe. The engine light came on and stayed on. When checked, here is the code that appeared: TPS/PEDAL POSITION SENSOR ACKT RANGE/PERF. I am assuming the code deals with the...


If it is a code P0226 I would not consider it a safety issue.


Throttle position (TP) sensor C/accelerator pedal

position (APP) sensor ? - range/performance problem


Possible Causes: Accelerator cable adjustment, TP/APP sensor

Throttle position (TP) switch C/accelerator pedal position

(APP) switch ? - range/performance problem
Accelerator cable adjustment, TP/APP switch

This might only be an adjustment issue--make sure the throttle cable isn't so tight that the throttle cannot fully close.
If the cable is OK, it is probably the accelerator position sensor under the pedal.
There are procedures for testing the unit that I will paste below if you care to try them.

If you just want a shop to fix it, the part is about $50 and labor should only be 30 minutes.


Operation The sensor is made up of the two individual sensors within a single housing. Each sensor has a unique functionality to determine pedal position. The APP system along with the Powertrain Control Module (PCM) is used to calculate and control the amount of acceleration and deceleration through fuel injector control.


Removal & Installation

  1. Remove the driver-s side knee bolster.
  2. Push down on the small tab and disengage the electrical connector.
  3. Remove the pedal bolts and remove the pedal and sensor assembly.
  4. Installation is the reverse of removal.

    5bcaece.gif

Fig. APP sensor mounting
Testing

  1. Install a 3 amp fused jumper wire between the 5-volt reference terminal of the APP sensor and 5 volts. Install a jumper wire between the low reference terminal and a ground.
  2. Sweep the sensor through the entire range while monitoring the voltage between the signal terminal and the low reference terminal with a digital multimeter. The voltage should vary between 0.30-4.98 volts without any spikes or dropouts.
  3. If the voltage is not within the specified range or is erratic, replace the accelerator pedal assembly.

Oct 06, 2010 | Chevrolet Tahoe Cars & Trucks

Not finding what you are looking for?
2003 Ford F350 Super Duty DRW SuperCab Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...