Question about 1999 Toyota Camry

Open Question

How do I remove a console from a 1999 Toyota

How do I remove the console from a 1999 Toyota Camry?I am attempting to replace the transmission cable and believe that I need to remove the console to do this...
Thank You

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: 1998 toyota camry interior dome light replacement

Look closely at the cover. You will see a small slot. Insert a small flat blade screwdriver, and pry it off. Very easy..

Posted on Nov 10, 2008

thaurfen
  • 623 Answers

SOURCE: Need to replace timing belt

having them changed by a certified mechanic is your best bet,Timing belts are a wear item. Most are to be changed every 60,000 miles for preventive maintenance. They may break causing expensive damage to interference engines due to the collision of valves and pistons as they go out of sync.Having them replaced at intervals is the best way to save yourself from a very costly repair.The task of the timing belt

Posted on Jul 29, 2008

  • 1 Answer

SOURCE: 1999 toyota camry horn beeping when i replace the battery

I put a new started in my 99 camry the alarm went off and I didn't know how to stop it ,now my car doesn't have any power the battery is new but its not giving my car any power.Help...

Posted on Oct 09, 2008

  • 98 Answers

SOURCE: How to remove ignition cylinder from Toyota Camry 1993

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

Posted on Nov 23, 2008

  • 1861 Answers

SOURCE: INSTALL SIDE VIEW MIRROR ON A 1997 TOYOTA CAMRY

Yes, you have to remove the door panel.

Remove the 2 plastic protectors on the front edge, and remove the 2 brass colored screws. Next, remove the push pins from the latch side. Push in, and pull out the whole thing. Next, under the armrest, remove the screw. Lift up the power windoe control, being careful to not break the plastic retainer tab. Remove the screw under the window control. Starting at the bottom, pull out the panel, and, when all of the clips are loose, pull the panel straight up. It is best to do this with the door panel as warm as possible, like in a heated garage. Doing this outside in the cold will break all of the plastic retainer clips; they are quite brittle whn cold.

I hope this helps

Thanks for choosing FIxYa for assistance. A FIxYa rating (4 blue diamonds) would be greatly appreciated.

Posted on Feb 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the automatic transmission in toyota camry 1999


drop the engine take it off put new one one put engine back in

Nov 19, 2015 | 1999 Toyota Camry

1 Answer

99 toyota camry has transmission very tight.. sometimes its very hard for me to change from drive to park


Disconnect shif cable from trans and see if it changes. If no change suspect a bad cable or worn bushings in shifter assembly.If cable is free when it is disconnected seek professional help with transmission.

Jan 11, 2011 | 1999 Toyota Camry

1 Answer

How to repalce kickdown cable of toyota camry


you have to remove the trans pan and the valve body in the transmission

Feb 24, 2010 | 2000 Toyota Camry

1 Answer

How to install a starter on a 2000 Toyota Camry


Disconnect the ground cable, remove the cables connected to the starter, remove the two bolts that are holding the statter to the body of the transmission and remove the starter motot out.

instalation is the reverse of removal!!!

Nov 16, 2009 | 2000 Toyota Camry

1 Answer

How do you fix a shift cable


To replace the shifting cable for the gear selection, you have to remove first the console box where the gear shift lever is and once you have access to the cable look for a lock that connects the cable to the shifting lever and remove it. do the same on the transmission side of the cable, then when the cable is free from the linkages attached to it pull it out with care. If it is stuck on the brackets loosen and give a slight **** on the cable.

Oct 27, 2009 | 1989 Toyota Camry

1 Answer

Cassete player does not automatically rewind.


radioaudiol.jpg&size=16&dhm=60b66153&hl=en 1999 TOYOTA CAMRY Radio Audio
$112.32 used - LowMileageParts.com Metra 99-8218 Toyota Camry 2007-UP Dash kit
$30.29 new - Amazon.com 1999 TOYOTA CAMRY Radio
$159.99 used - everdrive.com

Installation and Removal procedure

www.installdr.com/InstallDocs/Toyota/PDF/869037.pdf

Oct 22, 2009 | 1999 Toyota Camry

2 Answers

How do i remove headlight assembly on 99 camry?


This video will show you how to remove them on your vehicle.">

Apr 19, 2009 | 1999 Toyota Camry

2 Answers

My speedometer does not work on my 96 camry


Depends on what you put it in the shop for???
There is a little actuator that bolts in the top/side of the transmission, and then an electric plug is plugged into it... make sure its plugged in////

Oct 21, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
1999 Toyota Camry Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...