Question about 1990 Honda Accord

Open Question

Need to see picture of how the brackets go back in on honda accord blower motor 1990

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blower motor replacement


For honda accord blower motor replacing,click this link below and follow the step by step procedure :----
http://technoanswers.blogspot.in/2012/02/how-to-replace-blower-motor-on-1990.html
----------This will help.Thanks.

Jan 28, 2012 | 1990 Honda Accord

1 Answer

Why dont the blower work on my 1990 honda accord LX


Is it all speeds it doesn't work or just certain speeds? 2 posssible things to look for first is either the blower is bad or else the variable speed resister may be bad. There is a chance that the switch is bad but I would check the other first. If you can pull the blower motor and put 12v to it and it works, then it might be the resister. If you only have certain speeds that work then it may be the resister.

Oct 22, 2011 | 1990 Honda Accord

2 Answers

I cant find the blower motor


If you mean the climate control blower motor, it's usually under the dash on the passenger side on Hondas.

1990-93 Accord
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support) Fig. 2: Remove the glove box and frame 86806004.gif

  4. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.
  5. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly. Fig. 3: Air conditioned models require the removal of the control unit. Handle it carefully 86806005.gif
      Fig. 4: Remove the lower covers from the blower unit 86806006.gif
      To install:
  6. Install the blower unit and tighten the retaining nuts.
  7. On air conditioned vehicles:
    1. Install the lower covers and the retaining band.
    2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
    3. Install the kick panel and reposition the carpet.
  8. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
  9. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
  10. If applicable, enable the SRS.
  11. Connect the negative battery cable.
1988-91 Prelude
  1. Disconnect the negative battery cable.
  2. Remove the glove box and frame (lower support).
  3. Remove the 4 screws and remove the heater duct. Fig. 5: The glove box and frame are secured by several small screws 86806007.gif

  4. Remove the 3 mounting bolts.
  5. Unplug the wiring connectors from the blower motor, resistor and recirculation controller. Remove the blower motor assembly.
  6. Reinstall in reverse order. Make certain the blower mating surfaces are tightly sealed.

Jan 08, 2011 | 1992 Honda Accord

1 Answer

Where is the blower motor located for a 1993 honda accord


1990-93 Accord (click for zoom)

127c766.jpg

Fig. 1: Remove the glove box and frame


d9da350.jpg

Fig. 2:
Air conditioned models require the removal of the control unit. Handle it carefully


7151369.jpg

Fig. 3: Remove the lower covers from the blower unit



Hope help with this (remember rated this).

Jul 09, 2010 | 1993 Honda Accord

1 Answer

Where is the blower motor relay on a 1990 Honda Accord?


in the fuse block under the hood on the passenger side

Nov 22, 2009 | 1990 Honda Accord

1 Answer

Need to replace blower motor on 1990 honda accord ex


It's above the pass side floorboard, kind of behind the glove box, but lower. You'll need 8mm or 5/16" socket. Loosen the bolts, lower it and unplug it, pull it out. Don't throw it away, sometimes you have to keep your fan blade when you buy a new one. A junkyard will give you one with it still on...

Sep 28, 2009 | 1990 Honda Accord

2 Answers

Cant find the thermostat on my 1990 honda accord


Find your upper radiator hose and follow it back to the engine. There should be a metal "bracket" that the hose joins with a hose clamp. You'll find your thermostat in here.

Jul 02, 2009 | 1990 Honda Accord

2 Answers

How do i remove the rotor for a 1990 honda accord


remove caliper, caliper bracket it may or may not have a screw that holds it to the hub pretty easy actually

hope2help

Apr 05, 2009 | 1990 Honda Accord

1 Answer

How do i pull out a faulty heater blower motor from behind glovebox in 91 accord?


For Pictured Detailed Innstruction see Bottom of Page


BLOWER UNIT REMOVAL
  1. Remove the glove box.
2. Remove Glove box FRAME
3. Pull back the carpet and remove the kick panel. Remove the control unit bracket mounting nuts (4). Disconnect the connectors (5) and remove the control unit and bracket.

  1. Without A/C:
    • Remove the self-tapping screws (3) and remove the heater duct.
    • Remove the blower (3 nuts).
  • If the car has A/C, remove the blower unit according to the sequence shown
  • BLOWER MOTOR REPLACEMENT
    Refer to illustration for blower unit disassembly and reassembly, noting the following:
    • Before reassembly, make sure that the air door and linkage moves smoothly without binding.
    • When reattaching the recirculation control motor, make sure its positioning will not allow the air door to be pulled too far. Attach the recirculation control motor and all linkage, then apply battery voltage and watch the recirculation control door movement. If necessary, loosen the holding screw and move the recirculation control motor up or down
    • CONTROL ROD ADJUSTMENT
      Connect the recirculation control motor connector to the main wire harness and turn the FRE/REC switch to "REC". Hold the air door closed, then connect the control rod to the clip on the arm.
    • Email Me at the nickkname shown here >>rejakwilson @aol.com

Jan 18, 2009 | 1991 Honda Accord

1 Answer

Air and heater


  1. Disconnect the negative battery cable.
  2. Remove the glove box.
0900c1528005f9e2.jpgFig. 1: The blower motor assembly is secured to the right side of the dashboard
  1. Remove the duct between the blower and heater box.
  2. Unplug the wiring connector and the vacuum hose from the blower.
  3. Remove the three mounting bolts and remove the blower assembly.
  4. Install in reverse order, tightening the mounting bolts to 7 ft. lbs. (10 Nm). Make certain the blower mating surfaces are tightly sealed. Install the blower duct; make certain there is no leakage at its joints.
1990-93 Accord
See Figures 2, 3 and 4
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support)
0900c1528005f9e3.jpgFig. 2: Remove the glove box and frame
  1. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.
  2. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly.
0900c1528005f9e4.jpgFig. 3: Air conditioned models require the removal of the control unit. Handle it carefully 0900c1528005f9e5.jpgFig. 4: Remove the lower covers from the blower unitTo install:
  1. Install the blower unit and tighten the retaining nuts.
  2. On air conditioned vehicles:
    1. Install the lower covers and the retaining band.
    2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
    3. Install the kick panel and reposition the carpet.
  3. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
  4. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
  5. If applicable, enable the SRS.
  6. Connect the negative battery cable.

Oct 16, 2008 | 1990 Honda Accord

Not finding what you are looking for?
1990 Honda Accord Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...