Question about 1989 Ford F 150

1 Answer

My fuel gauge is reading full all the time.how do i fix the problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 76,846 Answers

This problem is only caused by one thing that is the fuel gauge sending unit inside the fuel tank, replace it.

Posted on Sep 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel pump wiring diagram


there is two things : fuel gauge and dash fuel gauge. The fuel gauge in tank rated to 0 to 90ohms.disconnect wire at the tank take a variable resistor connect it to wire .read the dash gauge if it move as you move the resistor. if ok fuel tank gauge is at fault

Aug 09, 2013 | 1998 Chevrolet K1500

1 Answer

Took my car in because of a gas leak and gasgauge that reads FULL all the time.. mechanic replaced the fuel pump but can't get the gas gauge to not read FULL. What to do?


If he told you the fuel pump would correct the fuel guage, take the car back and make them fix it under warranty. I have been in the auto repair business for 21 years and if I mis-diagnose a car, I have to fix it for free to keep the customer happy.

Oct 04, 2012 | 2002 Saturn L-Series

1 Answer

2003 kia Sedona fuel gauge problems


tank sender/ sensor problem more that a fuel pump
run the fault codes

Nov 16, 2017 | Kia Sedona Cars & Trucks

1 Answer

Hi, i have 92 civic 4dr the fuel gauge always stays on full, how can i fix it ?


Sounds like the ground wire is bad, any time the gauge reads full all the time is the ground wire is bad

Apr 13, 2011 | 1992 Honda Civic

1 Answer

2005 PT Cruiser fuel gauge is wrong suddenly. Put gas in and still shows empty


2005 PT cruiser, i replaced the cam sensor with a aft market sensor my fuel gauge started reading wrong, and it didn't fix my problem so i replaced the cam sensor with a factory sensor it fix my running problem but the fuel gauge still reads wrong, with a full tank of gas the gauge reads 3/4 tank,

Feb 28, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Gas gauge reads full when underway. However, when


Most likely it a bad fuel level sensor on you fuel pump. You will have to replace the fuel pump as that is the only way to replace the sensor for you fuel gauge. The sensor is built into the fuel pump. The contacts on the sensor become corroded over time and cause the sensor to malfunction causing your fuel gauge to read full all the time. I have a 2001 Montana extended version that had the same problem. In order to know when I needed to fill the tank, I would completely fill it each time I put fuel in and reset my trip odometer. I would go 400 miles on the tank before I would refuel until we were able to replace the fuel pump.

Oct 30, 2009 | 2000 Pontiac Montana

2 Answers

Fuel gauge not working all the time.


This is a normal concern.
The instrument cluster uses 4 different operating modes to calculate the fuel level:
Anti-slosh (default mode)
Key OFF fueling
Key ON fueling
Recovery
After a fuel fill up, the time for the fuel gauge to move from empty (E) to full (F) ranges from 2 seconds to 55 minutes depending on which operating mode the fuel gauge is in.
The default fuel gauge mode is called the anti-slosh mode. To prevent fuel gauge changes from fuel slosh (gauge instability due to changes in fuel sender readings caused by fuel moving around in the tank), the fuel gauge takes approximately 55 minutes to go from empty (E) to full (F).
The key OFF fueling mode (2 seconds to read empty [E] to full [F]) requires 3 conditions be met:
The key must be in the OFF position throughout the entire refueling of the vehicle.
At least 15% of the vehicle's fuel capacity must be added to the fuel tank.
The instrument cluster must receive a valid key ON fuel sender reading within 1 second of the key being put into the RUN position. The key ON sample readings are considered valid if the fuel sender reading is between 15 ohms ± 2 ohms and 160 ohms ± 4 ohms.
If these conditions are not met, the fuel gauge stays in the anti-slosh mode, which results in a slow to read full (F) event.
The key ON fueling mode (approximately 90 seconds to read empty [E] to full [F]) requires 3 conditions be met:
The transmission is in PARK (P).
The key is in the RUN position.
At least 15% of the vehicle's fuel capacity must be added to the fuel tank.
In key ON fueling mode, a 30-second timer activates after the transmission is put into the PARK (P) position (automatic transmissions). When the 30-second time has elapsed and at least 15% of the vehicle's fuel capacity has been added, the fuel gauge response time is 90 seconds to read from empty (E) to full (F). When the transmission is shifted out of PARK (P), the fuel gauge strategy reverts to the anti-slosh mode. The key on refueling mode prevents slow to read full events from happening if the customer refuels the vehicle with the key in the RUN position.
Recovery mode is incorporated into the instrument cluster strategy to recover from a missing fuel level input during a refueling event. Missing fuel level inputs result from intermittent opens in the fuel sender or its circuits. Recovery mode (empty [E] to full [F] approximately 20 minutes) is initiated when the following 2 conditions are met:
The instrument cluster is in the anti-slosh (default) mode.
The actual fuel level in the tank is greater than what is being displayed by the fuel gauge

Feb 18, 2009 | 1983 Mercury Grand Marquis

1 Answer

2003 Ranger Edge Fuel gauge


CHECK ENGINE LIGHT ON READS FUEL SENSOR
AND 5 CYLINDER

Dec 31, 2008 | 2003 Ford Ranger Regular Cab

1 Answer

97 montana fuel gauge reading over full all the time


it is a sensor issue take it to a look dealer or a local mechanic and he can fix that for u

Nov 28, 2008 | 1999 Pontiac Montana

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...