Question about 1989 Honda CRX

1 Answer

1989 honda crx 1.5 automatic won't start. Replaced igniter, distributor, rotor plugs,wires,engine turns but will not start

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Honda Expert
  • 268 Answers

Check the timing belt or check the most common item, the Main Relay. It controls spark and fuel.

Posted on Sep 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced starter on 1989 f150 5.0 now have no spark


Mike, Check for diagnostic codes. Check fuses/relays,wires/plugs for pinched,damage or corrosion. Could be a lot of things like distributor armature, cap, rotor, stator, ICM, coil,spark plugs,wires, make sure ground is good to distributor. Use the attached forum links,instruction, guides to help diagnose ignition spark problems, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
No spark replaced all ignition parts 1990 F150 Ford F150 Forum Community...
Engine Spins but No Start No Spark
Engine Won Start No Spark
Code Reader 80 96 Ford Bronco
Resolved 89 Ford F150 302 Won Start HELP

Jun 24, 2016 | Cars & Trucks

1 Answer

1991 Honda crx won't start


Try tracing the wires and looking for a worn spot in insulation that is grounding out, its a royal pain but might be the only solution, use wire prob and test areas where inaccessible. good luck

Jun 09, 2012 | 1991 Honda CRX

1 Answer

1990 honda crx jerks when i press the gas


I think you need a tune up spark plugs and plug wires distributor cap and distributor rotor

May 16, 2012 | 1990 Honda CRX

2 Answers

CAR WON`T START.


hi the major problem is due to the single spade type connector going to a switch.. By means of a throttle pulley disconnected it and ur problem will be solved very simple... The switch must have gone bad...

thnk u!!!
rate me!!

May 01, 2009 | Honda CRX Cars & Trucks

2 Answers

89 crx has power but wont start.


replace the ignition control module,I recommend a new one,if you order a rebuilt dist.it comes with a used one that only passed cold temp bench test they usually have problems once the car warms up. so get a new one!good luch let me know if you need more info have a good day DB

Feb 14, 2009 | 1989 Honda CRX

1 Answer

1989 honda crx


If you haven't had the distributor out then turn the cam so the rotor points to No.1. Then yiou should see some marks either lining up or close to it.
If you have had the distributor out, set the cam and then worry about the distributor.
Some engines have more than one possible location for the cam gear. I'm not 100% about Hondas so I can't comment either way. Sorry.

Jan 04, 2009 | 1989 Honda CRX

1 Answer

1989 honda crx timing issues


This is the tricky part... as I mentioned in my solution, When you install the distributor, the shaft will turn because of the gears. You are going to have to pull the distributor just enough so that the gears aren't meshing together and turn the shaft.take notice of which way the shaft turns when you remove the distributor. Once the gears aren't meshing, turn the shaft to the #1 position and go a little past the #1 position in the opposite way that the shaft turned.install the distributor and see where the rotor sits then.if it is still not in the right place, pull it again and go one gear tooth at a time until the rotor lines up with the #1 position. Hope this helps. If you still need more info or clarification, don't hesitate to ask.

Phil

Jan 03, 2009 | 1989 Honda CRX

1 Answer

Cam positioning


did you adjust the rocker arm on the head

yes

then you check spark and fuel

check ur cel for codes

Jan 02, 2009 | 1989 Honda CRX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...