Question about 2000 Ford Crown Victoria

1 Answer

My 2000 ford crown victoria's driver side windshield wiper will not stay tightly on the windsheild when i get over 40 it gets worse until it does not wipe at all. Tried replaced the blade nothing, the arm , nothing.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 45 Answers

I usually start with the blade as well, the arm can be bent in a method to make it arch high higher in the middle of the arm - forcing more downward pressure onto the windshield. The real problem however, could be your windshield. Not that I believe that all Ford vehicles should have the "Carlite" stamp on the glass, there are other good brands of glass. But, some glass manufacturers have poor quality control and their glass molds produce some parts with flat spots, low spots, high spots and many other distortions in the glass. Does your windshield have a Carlite stamp at the lower part of the windshield? If you can't adjust the wiper to work, you may want to consider the glass instead.

Posted on Sep 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiper timing switch


Susan, inside the wiper motor is a parking peg which controls the position of wiper blades when off, It is possible the peg is damaged or broken. The wiper motor would have to be replaced in this case. You can find a used one at the auto wreckers, just make sure the plug is the same as yours, as they may be different from one year to another.Have a good Tech. check wipers, diagnose and estimate repair.
Check the attached links,instruction and guides, 1 st link gives procedure to change wiper motor. Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://boards.straightdope.com/sdmb/showthread.php?t=240691
Wipers will not park Body and Interior Crownvic net
2000 Ford Crown Victoria Windshield Wiper Issues Electrical

Aug 21, 2016 | 1999 Ford Crown Victoria

1 Answer

1996 crown vic- drivers side wiper arm loose, blade will not lay flat when cleaning


Sometimes you need to bend the arm to put more pressure on the glass.

Mar 29, 2014 | 1996 Ford Crown Victoria

1 Answer

1989 ford crown victoria windshield wipers inoperative


check in Power Distribution Box, position 110, 30AMP (Cartridge fuse) for Wiper Module.

Jun 13, 2011 | 1989 Ford Crown Victoria

1 Answer

Ware is the wiper module located on a 2000 crown victoria


Follow the Dark Blue/White wire or Brown/White wire from the Multifunction Switch to the wiper module according to the schematic.
Also, one can trace the wires from the windshield wiper motor to the wiper module by peeling away the wiring loom and looking for a Yellow/Red wire that leads to the module.
---
Windshield Wiper Motor Removal & Installation To Remove:
  1. Remove the mounting arm and pivot shaft assembly.
  2. Remove the windshield wiper motor cover.
  3. Remove the clip.
  4. Disconnect wiper transmission linkage.
  5. Remove the bolts.
  6. Remove the motor.
To Install:
  1. Position the wiper motor.
  2. Install bolts. Tighten to 10 Nm (89 in. lbs.).
  3. Connect wiper transmission linkage.
  4. Install clip.
  5. Install wiper motor cover.
  6. Install mounting and pivot shaft assembly.
prev.gif next.gif

Oct 28, 2010 | 1999 Ford Crown Victoria

1 Answer

2002 ford crown vic. driver side wiper not working? passenger side works


the linkage between the wiper motor and the wiper arms needs to be replaced. the stud on the one side is stripped and that is why it doesn't work as it should. this happens usually when the wipers are left on in the winter with the blades freezing to the windsheild. turn on the car with frozen blades tends to strip out the teeth holding the wiper arms onto the linkage

Jun 09, 2010 | 2002 Ford Crown Victoria

1 Answer

Windsheild wipers


Should be fuse #2 - 30 amp


Jan 24, 2010 | 2000 Ford Crown Victoria

2 Answers

Windsheild wiper switch


Here's a video that will show you how to replace the multifunction wiper switch on a 03-10 Crown Victoria.
">

Nov 07, 2009 | 2003 Ford Crown Victoria

3 Answers

Can't find fuse for windshield wipers in 2008 Ford Crown Victoria.


Fuse no. 7(10amp) in interior fuse panel and fuse no.110 (30amp) in underhood fuse panel

Mar 02, 2009 | 2008 Ford Crown Victoria

Not finding what you are looking for?
2000 Ford Crown Victoria Logo

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...