Question about 1995 Nissan Maxima

Open Question

How do you install a rear vent window - 1995 Nissan Maxima

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install quarter window that flips out on 2003 dodge Dakota. 2 door.right side


REMOVAL

(1) Remove quarter trim panel.

(2) Remove the bolts attaching the latch to the cab


side panel.



(3) Remove the nuts attaching the frame/hinge to

the B-pillar.

(4) Remove the glass from the cab.
(5) If necessary, remove the latch from the glass.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

Oct 02, 2016 | 2003 Dodge Dakota

3 Answers

How do i close back windows


There are 3 switches above the rear view mirror. The middle one controls the back windows. Push up to open and down to close.

Jun 13, 2014 | 2004 Lincoln Navigator

1 Answer

1998 ford explorer rear window removal


Hi there:

  1. Remove the door trim panel and speaker if applicable.
  2. Remove the screw from the division bar. Remove the inside belt weatherstrip(s) if equipped.
  3. Remove the 2 vent window attaching screws from the front edge of the door.
  4. Lower the glass and pull the glass out of the run retainer near the vent window division bar, just enough to allow the removal of the vent window, if equipped.
  5. Push the front edge of the glass downward and remove the rear glass run retainer from the door.
  6. If equipped with retaining rivets, remove them carefully. Otherwise, remove the glass from the channel using Glass and Channel Removal Tool 2900. Remove the glass through the belt opening if possible.

To install:
  1. Install the glass spacer and retainer into the retention holes.
  2. Install the glass into the door, position on the bracket and align the retaining holes.
  3. Carefully install the retaining rivets or equivalent.
  4. Raise the glass to the full closed position.
  5. Install the rear glass run retainer and glass run. Install the inside belt weatherstrip(s).
  6. Check for smooth operation before installing the trim panel.



Hope this helps.

Feb 28, 2013 | 1998 Ford Explorer

3 Answers

My back automatic window went down and now won't come back up. No sound from motor. Checked fuses. Even took back seat apart but don't know what to do or what caused it. How can I get window to go...


it may need to be reset.

SECTION 501-11: Glass, Frames and Mechanisms 2001 Explorer Sport/Sport-Trac Workshop Manual
GENERAL PROCEDURES Rear Window Motor Initialization s1r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.
  1. Start with the ignition in the OFF position.
  1. Turn the ignition to the ON position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the OFF position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.
  1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
  1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions.
------------------------------------------------------------------------------------
  • The power rear window is inoperative (Explorer Sport Trac only)
  • Circuitry.
  • Battery Junction Box (BJB) fuse 3 (30A).
  • Central Junction Box (CJB) fuse 20 (7.5A).
  • Power rear window control switch.
  • Rear window glass motor.
  • Go To Pinpoint Test K .

------------------------------

Sep 15, 2011 | 2001 Ford Explorer Sport Trac

1 Answer

Where is the rear window relay located on the 2002 Ford Explorer sport trac. Not the rear door windows but the very back window.


  • The power rear window is inoperative (Explorer Sport Trac only)
  • Circuitry.
  • Battery Junction Box (BJB) fuse 3 (30A).
  • Central Junction Box (CJB) fuse 20 (7.5A).
  • Power rear window control switch.
  • Rear window glass motor.

NOTE: The power rear window motor is not on the multiplex link. Any diagnosis and testing carried out on the power rear window will not involve the GEM module. NOTE: The reinitialization procedure must be carried out when repairs are performed on any part of the power rear window system including when the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.

Rear Window Motor Initialization s1r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.
  1. Start with the ignition in the OFF position.
  1. Turn the ignition to the ON position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the OFF position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.
  1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
  1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions
---------------------------------------------------------------------------------------------

Nov 16, 2010 | 2001 Ford Explorer Sport Trac

1 Answer

Power window on drivers back window will not close


if your talking about the rear vent windows it will probably be the vent motor,we've installed alot of them that just quit

Jan 17, 2010 | 1999 Dodge Caravan

2 Answers

Need to replace a broken window on rear passenger 1999 jeep chero


This information can help you to fix it:
- Section-08s-Power-Window-Systems-Ewj8s
- Section-23-Body-ewj23S (Rear Door, page 41 and next).

Good luck (remember rated this help).

Sep 09, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Passenger window and rear vent window stopped working


YOU PROBABALY MAVE A BROKEN WIRE IN THE HARNESS THAT GOES FROM THE DRIVERS DOOR TO THE INSIDE OF THE VEHICLE

Jul 24, 2009 | 1999 Chrysler Town & Country

1 Answer

Passenger side rear power window is not opening...car is 2003 Honda Odyssey....at times it opens up a little bit....


the rear side window vent motor is bad, u need to replaced it...common on these vans...i hope its the left rear and not the right....right is a little more difficult re installing due to the rear a/c ducts

Apr 07, 2009 | 2003 Honda Odyssey

Not finding what you are looking for?
1995 Nissan Maxima Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...