Question about 2003 Ford Crown Victoria

3 Answers

Why does my 2003 ford crown victoria at 55 mph begins to shake in steering wheel

Posted by on

  • roachrlsj990 May 11, 2010

    Need more info to try to diagnose problem. 1. How old are the tires? 2. Have they been balanced & rotated every 6 months/6,000 miles? 3. Are they unevenly worn? 4. How much tread is left? 5. Is anything odd showing through tread or sidewall? 6. Is air pressure same between both fronts & both rears? 7. Has there been recent work done to the car?

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 104 Answers

IT SOUNDS LIKE YOU EITHER NEED TO HAVE THE FRONT TIRES BALANCED,OR HAVE A BAD TIRE,OR IT COULD POSSIBLY HAVE A BAD TIE ROD,OR A BAD RUBBER BUSHING THAT HOLDS THE RACK, BUT I WOULD TRY THE BALANCE ON THE TIRES FIRST, ESPECIALLY IF IT SEEMS TO GET BETTER IF YOU SPEED UP & YOU FEEL IT START TO GET WORSE AFTER IT SMOOTHS OUT & YOU CONTINUE TO GO FASTER ,BUT SMOOTHS BACK OUT AS YOU SLOW DOWN SOME ,BUT IF IT GETS WORSE AS YOU SPEED UP I WOULD START WITH CHECKING THE TIRES FOR A TWISTED BELT OR KNOT ON ONE OR BOTH FRONT TIRES ,AND GO FROM THERE IF THAT DOESN'T WORK.

Posted on Dec 05, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 45 Answers

I believe that a visit to a tire shop and have the wheels balanced should correct your issue.

Posted on Sep 27, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

You probably have a loose front end part.And could have a tire out of balance.

Posted on Sep 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 2007 Crown Victoria Police Interceptor vibrate when I get to 40 miles an hour and then die off back to normal by the time it reaches 50


Ford Crown Victoria Questions - what would cause a whole ...

www.cargurus.com > Questions > Ford > Crown Victoria
CarGuruswhat would cause a whole car vibration when going between 48 and 65 mph, even ... Asked by Dfranz Aug 29, 2013 at 11:53 AM about the 2001 Ford Crown Victoria Police Interceptor ... You have an open diff by turning one wheel the driveshaft should turn before the .... 2007 Ford Crown Victoria Police Interceptor For Sale.

Nov 03, 2015 | Cars & Trucks

2 Answers

2003 crown victoria won't come out of park


Had a similar problem. Solved it two ways first place key in the 3 position move gear to N then start and it will shift easily. Second solution check brake light fuse, it is probably blown replace it and gears will shift OK.

Jul 01, 2012 | 2003 Ford Crown Victoria

1 Answer

Vibration in Cab of Truck


sounds like a bent wheel rim

May 14, 2012 | Ford F-150 Cars & Trucks

2 Answers

The car shakes at 35 mph then as you increase speeds the shaking disappears then starts shaking again at 63 mph....the shaking is both in the wheel and in the seat .I had the wheels balanced to no avail...


It can be the suspensions or the shock absorbers, check also the engine mountings.
i will be good to take a full checkup of all the links and suspension bushes in the car. so a full test on the shocck absorbers, test the wheel bearings the hubs and if the discs are bend even is if the balancing was done.

Sep 21, 2010 | 2003 Ford Crown Victoria

1 Answer

I need fuse panel diagrams for ford crown victoria 2002 police interceptor


For check passenger compartment fuse panel, is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses.

Other details and descriptrions can find it in 2003 Ford Crown Victoria - Owners Manual (page 164 and next).

Hope helps (remember rated this).

Aug 04, 2010 | 2003 Ford Crown Victoria

1 Answer

2003 ford victoria horn not working, what do I do I changed the fuse and I have a the police package


In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to follow factory Airbag disarming protocol can result in an unexpected Airbag deployment and possible serious personnel injury

Mar 25, 2010 | 2003 Ford Crown Victoria

1 Answer

Light want stay on my 2003 crown vic


probably a connection
open the wire box under the steering wheel and look for wires that are not connected
good luck

Feb 23, 2010 | 2003 Ford Crown Victoria

1 Answer

THE CHECK ENGINE LIGHT STAYS ON AND THE CAR SURGES


Check your throtle position sensor. You need to check the code when the light is on.

Oct 20, 2009 | 1995 Ford Crown Victoria

3 Answers

At 40 mph the car starts to shake. It last to 5o


I have this same car with exactly the same problem. Begins shaking at 40mph and stops shaking as soon as you let off the gas, but then begins again as soon as you press on the gas and smooths out as you get over 50. And the shaking is not felt through the steering wheel. Solution: Replace the transmission mounts. There are two of them, one on each side mounted on the frame right next to the shock strut. There is also a front and rear engine mount, but I replaced the two as described and shaking is gone.

Jun 29, 2009 | 2000 Buick LeSabre

1 Answer

2003 ford crown vic hard steering


i would have to say to check for a relay in your fuse boxes for power steering pressre switch or it may have its own police pkgs have a lot of relays due to all the extras

Sep 10, 2008 | 2003 Ford Crown Victoria

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...