Question about 1999 Jeep Cherokee

2 Answers

Turn signals hazards flasher don't work jeep cherokee replaced combination flasher relay, turn signal switch and still no signals

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I NEED TO LOCATE THE SWITCH WHERE IS IT ?
MY INDICATORS NOR HAZARD LIGHTS ARE WORKING I DONT KNOW WHAT IS WRONG WITH IT CHANGED BULBS BUT NOTHIGN THEY ALL WENT OUT AT THE SAME TIME
SO THERE MUST BE A RELAY SWITCH SOMEWHER BUT DONT KNOW WHERE ?
THANKS FOR HELPING

Posted on Apr 01, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Did you ever get this resolved? My 99 Grand Cherokee Laredo has as similar problem with an intermitten left turn signal failure. Yet the 4-way flashers never fail. And I can usually "reset" the left turn signal by engaging the 4-way flashers. It comes and goes at will. I've replaced all the bulbs and the multifunction turn signal lever. The only thing left that I can determine is the combination flasher under the dash.

Posted on Mar 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 Jeep Grand Cherokee turn signals stopped working. The indicator light/chime also stopped working. Tried flasher relay and a new switch but still not working. Hazards work fine. Any ideas?


Did you check power an grounds with volt ohm meter ? you replaced the combination flasher ? Did you check fuse # 20 & 4 in the underhood junction box ? Pull the flasher relay an check for voltage in an voltage out , need a wiring diagram to do that ! Go www.bbbind.com free wiring diagrams !

Jul 24, 2015 | Jeep Cars & Trucks

2 Answers

What would cause my blinkers to stop working on a 2000 jeep cherokee sport?


Interesting, these are on the same circuit.

1) Click the hazards on and off a few times to exercise the switch.
2) Replace the flasher timer relay.
3) I believe that this system has a little computer center, about the size of a machbox and it is located under the dash. Swap this out with one from a junkyard.

May 22, 2014 | 2000 Jeep Cherokee

2 Answers

89 jeep cherokee blinkers and hazards not working


For 1989 Jeep Cherokee the Flasher is located:
* Front seating area, driver side, under dash, above kick panel, mounted in bottom of convenience panel for Hazard flasher
* Front seating area, driver side, under dash, above kick panel, mounted in top of convenience panel for Turn signal

Hope helps.

Apr 27, 2011 | 1989 Jeep Cherokee

1 Answer

Hazard lights turn on when i use my turn signal


Your model uses a combination hazard/turn signal relay.You need to remove the knee plate and its up to the left of the steering column.You need to reach up and remove the flasher unit and replace.Hope this helps

Sep 03, 2010 | 1999 Jeep Cherokee

2 Answers

I need a fuse panel diagram to replace the turn signal flasher. Thanks


Before replacing the flasher does the hazards work, Try wiggling the turn signal lever up and down and back and forth with the key on and the lever in each position. If the blinkers or hazards start flashing you'l need a multifuntion switch. This isnt a definative test if you get nothing you may have a blown fuse. As fas as the flasher goes, go buy one and then you will know what it looks like.

Jul 14, 2009 | 1998 Jeep Cherokee

1 Answer

My turn signal and hazard flashers are not


try replacing the combination flasher in the power distrobution center in the engine compartment, first row third one in

Jul 12, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Turn signals and hazards won't work on my 1997 Jeep Cherokee


under the hood of the vehicle there is another fuse/relay box, locate the signal flasher and try replacing that.

May 04, 2009 | 1997 Jeep Cherokee

2 Answers

Signal lights


where is the flasher relay located?

Oct 04, 2008 | 1995 Jeep Cherokee

Not finding what you are looking for?
1999 Jeep Cherokee Logo

1,916 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...