Question about 1999 Dodge Ram 2500 4WD

Open Question

Lm looking for a diagram for a 47re transmission valvebody

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install an input speed sensor for transmission on 05 Chrysler 300c 5.7


You have to remove the valvebody and change it as a unit, that disconnects from the top of the valvebody.

Oct 14, 2016 | Chrysler Cars & Trucks

1 Answer

How to remove valvebody from 2005 jeep libert 3.7L


the valvebody is in the transmission oil pan

Mar 30, 2015 | Jeep Cars & Trucks

1 Answer

Will the 42re4 from 2000 wj have the same electronic plugs as a1999 wj


did you look at the parts page? (at the least the plug, huh)
jeep.com list both as different. buying whole transmission.
call the wrecker and ask for hollander lookup on compat?

here is one seller on ebay that show campat
buy the harness and see capat,

http://www.ebay.com/itm/Transmission-External-Wire-Harness-Repair-Kit-Splice-In-42RE-44RE-46RE-47RE-48RE-/331364693032?pt=Motors_Car_Truck_Parts_Accessories&hash=item4d26dff428&vxp=mtr

"A500 , 42RE1993 Up"
A500 , 44RE1996 Up
A518 , 46RE1996 Up
A618 , 47RE1996 Up
48RE



Jan 12, 2015 | 1999 Jeep Grand Cherokee

1 Answer

Will a 99 ram 1500 2wd transmission work in a 97while 4wd?


let me guess no reverse. I blew mine 15 times one winter. the reverse in the 47re trans is made from aluminum and has 4 pinions. get a 48re same trans but stronger steel 6 pinion. you cant use the 2wd. need a 4x4 and If your keeping truck get a 48re not a bad 47re

Mar 24, 2013 | Cars & Trucks

1 Answer

Looking for the automatic valvebody and transmission schematics


We do not have these diagrams here at fixya and the only book that will show them in detail is the factory repair manuals. You can buy access to them here. www.alldatadiy.com

Jun 22, 2012 | Cars & Trucks

1 Answer

Transmission fluid capacity for a 1998 dodge ram 1500, V8


Transmission Fluid

42RE .................................................. 8.0-10.4L (8.4-11.0 Qt)
46RE .................................................. 9.0-11.0L (9.5-11.6 Qt)
47RE ................................................ 14.0-16.0L (14.8-16.9 Qt)

Jun 15, 2012 | Dodge Ram 1500 Cars & Trucks

1 Answer

Automatic transmission with shiftronic periodically when going into Drive goes to D1 or D2 on the console, stuck in low gear. A few days later the issue may go away. Just had the transmission rebuilt in...


dear friend-it looks like you have a dirty valvebody that is sticky,i would say that you can first try a additive to clean the valves and body,if no joy then you will have to remove the valvebody but take special care when stripping it.

Jul 30, 2009 | 2003 Hyundai Santa Fe

1 Answer

Automatic transmission on my 1997 sl1 gets stuck in 2nd or 3rd gear when car is warm. Is there an electronic shift control I can change to see if this is the problem


The issue is most likely due to a worn transmission valvebody. The problem will get worse over time. It is caused by not changing the transmission fluid often enough.

Only solution is to have the valvebody rebuilt or replace it with a new one. Its not a difficult job, but the removal and installation steps have to be follow precisely.

Jul 07, 2009 | 1997 Saturn SL

1 Answer

Trouble code P1740 on 1999 Dodge Ram 2500


I had the same code on my 2001 dodge 2500. The truck wouldn't shift from 3-4. I pulled the trans pan off and replaced a broken spring ($2.00). It is behind a thin plate with 3-4 small torq screws. You don't have to remove the valvebody. Only took me 45 minutes to fix.

I would like to give thanks to Jeff Russel from Teal automotive. He said this is a very common problem. He sells any part for any automatic Transmision and his prices are very affordable.
Here is a link to the website.
http://www.tealautomotiveinc.com/

Hope this helps.

Mar 15, 2009 | 2004 Dodge Ram

1 Answer

Jeep grand cherokee revs for to high before changing gear


Message:
My 2002 Dakota has been somewhat confused about shifting as well. It showed a code P1762. I dropped the pan to install a new fluid filter and fluid-(use only ATF+3 or ATF+4). Since the pan was off I decided to adjust the bands. The front band controls the 2nd gear cluster. The rear band controls the 3rd gear cluster and reverse. For a 2-3 shift, the transmission shifts back to 1st gear with the front band while the rear band engages 3rd gear. If the front band does not release the 2nd gear clutches before the third gear clutches engage, the transmission binds, which shortens the life of the transmission clutches. If the front band releases too early in the shift, the engine will overspeed (sounds and feels like a slip) during the 2-3 shift.
The front band adjusting screw is on the driver's side above the shift linkage. The rear band is inside the fluid pan near the filter.
1. Loosen band adjusting screw locknut. Then back locknut off 3-5 turns. Be sure adjusting screw turns freely in case. Apply lubricant to screw
threads if necessary. The front band adjuster is on the outside of the transmission and the locknut requires a 3/4" wrench.

2. Using Inch Pound Torque Wrench C-3380-A, a 3-in. extension and appropriate Torx� socket (T-40), tighten adjusting screw to 72 in-lb. CAUTION: If Adapter C-3705 (from SPX Miller) is needed to reach the adjusting screw, tighten the screw to only 47-50 in. lbs. torque.

3. Back off adjusting screw the number of turns listed below for your transmission.

4. Hold adjusting screw in place and tighten lock-nut to:

41 N�m (30 ft. lbs.) for the front band
34 N�m (25 ft. lbs.) for the rear band
The adjustment screw inside the case is a square head bolt. You will need a 1/4 square head socket to fit your torque wrench.
Band adjustments for each model year:
1994

* Front Band - tighten to 72 in-lb, back off 2-1/2 turns (all transmissions)
* Rear Band
o 32/42RH - Tighten to 72 in-LB, back off 4 turns
o 36/37/46/47RH - Tighten to 72 in-lb, back off 2 turns

1995-1996

* Front Band
o 42RH - tighten to 72 in-lb, back off 2-1/4 turns
o 46RH - tighten to 72 in-lb, back off 2-7/8 turns
o 47RH - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE/RH - tighten to 72 in-lb, back off 4 turns
o 46RE/RH - tighten to 72 in-lb, back off 2 turns
o 47RE/RH - tighten to 72 in-lb, back off 3 turns

1997-1998

* Front Band
o 42RE - tighten to 72 in-lb, back off 3-5/8 turns
o 46RE - tighten to 72 in-lb, back off 2-7/8 turns
o 47RE - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE - tighten to 72 in-lb, back off 4 turns
o 46RE - tighten to 72 in-lb, back off 2 turns
o 47RE - tighten to 72 in-lb, back off 3 turns

1999

* Front Band
o 42RE - tighten to 72 in-lb, back off 3 turns. (TSB 21-16-98)
o 47RE - tighten band adj. screw to 72 inch pounds, back off 1 7/8 turns
* Rear Band
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns
+ The 47RH rear band requires a 1/4" hex driver, the front band requires a
T-30 Torx driver, the filter is held in place by two screws which require a T-20 Torx drive

2000-2002

* Front Band
o 42RE - Tighten band adj. screw to 72 in-lb, back off 3 turns
o 44RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
o 46RE - Tighten band adj. screw to 72 in-lb, back off 2 7/8 turns
o 47RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
From Bill Konolday's 47RE notes: I usually go a little looser than factory
specs on this front band - backing off the adjustment screw 2 or 2 1/4 turns.
Depending on the circumstances I have backed off the band up to 2 1/2 turns.
* Rear Band
o 42RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 44RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 46RE - tighten band adj. screw to 72 inch pounds, back off 2 turns
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2003

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 1-3/4 turns
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2005

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds,
back off front band adjusting screw 1-3/4 turns for diesel vehicles,
or 1-1/2 turns, for V-10 vehicles.
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

94+ Automatic Transmission Bolt and Nut Torque Specs

* Front band adjustment locknut - 30 ft-lb
* Rear band adjustment locknut - 25 ft-lb
* Transmission pan bolts - 13 ft-lb
I just replaced the solenoid with the recommended transducer and all is fine now. The transducer cost me about $50 at a nearby dealership.
Hope this helps. -zman. rroszman@yahoo.com

Dec 09, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

551 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...