Question about 1996 Dodge Intrepid

Open Question

Trying to replace RF CV AXLE ON 96 DODGE INTREPID, NEED TO KNOW THE PROCEDURE TO REMOVE AXLE ?

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: front cv axle 1995 dodge intrepid

Naturally you need to remove the tire then the brake caliper. After the brake caliper is removed then you need to remove the 34mm axle nut that is inside the hub. After that is removed then you can remove the hub. Becareful not to damage the hub seal on the back or you will have to buy a new hub (100 or more). Then you need to remove the strut knuckle assembly. Once the knuckle assembly is removed then you can pull the CV axle. Take care the inner CV housing is held in place by an inner snap ring. You will probably have to pry off the inner housing. Once the axle is off then install the new axle (if you buy complete axle). Make sure if you are doing both that you take care which side you are installing. I made that mistake and double the work. Slide the new axle on the spline and make sure it is seated completely. Then put back together the reverse of removal.

Posted on Mar 24, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Universal joint


On a 2004 Intrepid it does not have Universal Joints, you will have Constant Velocity Joints. If you have one that is rough and noisy it will either need to be rebuilt or replaced. It is usually cheaper to replace the whole half shaft assembly that is it to rebuild one CV joint, this is also much easier as the whole axle is fully assembled. You just have to pop out your worn out pieces and install new axle.

Apr 24, 2013 | 2004 Dodge Intrepid

1 Answer

How to replace passenger cv joint 94 intrepid


as for your cv boot you will find you are cost ahead to replace cv axle . if you replace only the boot you have no warranty if you replace whole axle you have warranty not a hard job if you know how

Jan 10, 2013 | 1994 Dodge Intrepid

1 Answer

Tring to remove cv joint on 2001 intrepid but transaxel shaft seems stuck to cv joint cant dislodge.....does it have a lock or something.......whats the best way to remove


use a large pry bar pry the inner tripod cv joint out of the transaxle differential gears.you have a retaining circlip that holds transaxle in place in the transaxle.besure to replace circlip and o ring seal on the transaxle stub shaft.torque strut assembly to steering knuckle attaching bolts.install the nuts to the attaching bolts and while holding bolt heads torque to 125 ft lbs and torque axle hub nut 125 ft lbs

May 18, 2011 | 2001 Dodge Intrepid

1 Answer

How to remove front axle on a 2002 dodge intrepid


raise you vehicle on jackstands. remove front wheel and tire.remove front caliper from steering knuckle assembly, remove rotor from hub by pulling it staright off. remove speed sensor bracket from strut assembly. remove hub and bearing to stub axle retaining nut. dislodge inner CV stub shaft retaining ringon transaxle assembly. insert small pry bar between transaxle case and inner CV joint by prying on it.remove strut assembly to steering knuckle bolts remove top of steering knuckle from strut assembly, then rotate CV assembly out of vehicle. Remove inner shaft from transaxle stub shaft grasp inner CV joint and interconnecting shaft and pull both pieces out at the same time. good luck!

Oct 30, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

I have a dodge caravan 96. Motor is 3.3. I have a transmission leak. On the driver side of the transmission. I replace the seal, but the leak continue through the CV joint.


If it is leaking grease out of the cv joint, you will have to replace the rubber cv boot or eventually, the entire cv axle, if it gets worn because of lost grease and no lubrication.

Sep 22, 2010 | 1996 Dodge Caravan

1 Answer

Replace the Universal Joints, Dodge Intrepid 1997


Cv joints in your intrepid? Remove the tire, unbolt the lower ball-joint, Remove the hub nut, pull outer joint from wheel bearing, pull shaft from transmission.

Apr 22, 2010 | 2004 Dodge Ram 2500

1 Answer

How do I change out the cv axle?


WELL YOU NEED A HAYNES REPAIR MANUAL BECAUSE YOU HAVE CERTAIN PROCEDURES AND PHOTOS TELLING YOU HOW TO REMOVE THE CV SHAFT SO YOU WONT DAMAGE THE THREADS ON CV SHAFT.

Mar 05, 2010 | 1999 Dodge Intrepid

1 Answer

How to replace cvc axel on 2000 dodge interpid


you mean cv axle ? first you loosen the wheel lugs and axle nut in center of rim,if you have alloy wheels axle nut must be removed after wheel is off. then jack the car, and place a jack stand under it. remove the lower ball joint nut and disconnect it from spindle now remove the tie rod from the spindle as well .using a hammer tap out the axle.go underneathe and with pry bar pry it out from transmission.reverse for installation

Jan 09, 2010 | 2000 Dodge Intrepid

1 Answer

Cv axle replacement


a prybar flat end carefully pry inbetween shaft and trans housing a couple of quick prys and it should come out.

Jun 09, 2009 | 1999 Dodge Intrepid

1 Answer

Front cv axle 1995 dodge intrepid


Naturally you need to remove the tire then the brake caliper. After the brake caliper is removed then you need to remove the 34mm axle nut that is inside the hub. After that is removed then you can remove the hub. Becareful not to damage the hub seal on the back or you will have to buy a new hub (100 or more). Then you need to remove the strut knuckle assembly. Once the knuckle assembly is removed then you can pull the CV axle. Take care the inner CV housing is held in place by an inner snap ring. You will probably have to pry off the inner housing. Once the axle is off then install the new axle (if you buy complete axle). Make sure if you are doing both that you take care which side you are installing. I made that mistake and double the work. Slide the new axle on the spline and make sure it is seated completely. Then put back together the reverse of removal.

Mar 13, 2009 | 1995 Dodge Intrepid

Not finding what you are looking for?
1996 Dodge Intrepid Logo

Related Topics:

449 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...