Question about 2001 Chevrolet Blazer

Open Question

Where is the ebcm relay ay in my 2001 chev blazer 4x4 s 10

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tecnovative
  • 360 Answers

SOURCE: 1998 Chev Blazer 4x4 frnt wheel bearing torque

The torque spec for the axle nut is 103 lb ft.

Posted on Jan 13, 2011

Testimonial: "thanks"

Ad
  • 12 Answers

SOURCE: 1999 chev blazer 4x4 system

When you say that the 4wd won't engage, I assume you mean that the front differential is not locking in. If memory serves me correct there is a 3 port vacuum switch located on the top of the transfer case that gave a lot of problems. When the transfer case is shifted to a 4wd mode (high or low) this vacuum switch changes position and routes engine vacuum to the actuator located under the battery tray. This actuator then pulls a cable that move a fork inside the front differential that locks the front diff in 4wd. The vac switch gave a lot of trouble, but any broken vac hoses or differential internal mechanical issues could present as the same issue.

Posted on Nov 23, 2008

  • 2920 Answers

SOURCE: Can't get transmission out 2001 chev blazer

did you take the short shaft loose? even if it were seized it would still come out.you may have to wiggle it back and forth a bit to work it loose but it should come out.

Posted on Jan 08, 2009

  • 617 Answers

SOURCE: need a vacum hose diagram for a 2000 chev blazer

have diagram need email address to send to

Posted on Feb 09, 2010

BeninVa
  • 389 Answers

SOURCE: co265 ebcm motor relay circuit p/n 88982286

Hello, your EBCM is located on the frame underneath the vehicle just below the driver's seat. Sorry, I don't have a picture of it. Have you had brake work done recently?

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know if the EPM is interchangeable with any other year I own a 2001 Chevey blazer


clarify what you are talking about VCM PCM EBCM EHCU ECT EEPROM MAF .Spell it out I have several blazers

Mar 03, 2017 | 2001 Chevrolet Blazer

3 Answers

What is the C0265 error code


The ABS EBCM anti-lock brake module is failing causing problems with the ABS pump running constantly, also will drain your battery.
  1. Remove the ABS fuse to prevent ABS motor burn out.
  2. You can still drive your vehicle with the module removed.
  3. We recommend covering the exposed surface of the hydraulic control unit with aluminum foil to keep out water and dirt.
Common Failures:
  • ABS Pump Always Running
  • Codes: C0265, C0267, C0268
  • Pump Motor Circuit trouble code
  • Power Relay trouble code
  • Valve Relay Trouble code
  • Dump Valves (solenoids) trouble codes
  • No Communication
  • Intermediate power loss
http://www.myairbags.com/dtc-code-c0265-abs-ebcm-light/
ebcm-abs-control-module-failure-code-dtc-c0265-c0267-c0268-pump-running-y52j5yjvtwyljepizajwhmfx-1-0.jpg

Nov 28, 2014 | 2001 GMC Sierra C3

1 Answer

How to repair abs EBCM


EBCM relay is the actual fault code cause. EBCM stands for Electronic Brake Control Module. ECBM stands for Electronic Brake Control Module. It is the big part that the brake lines go into and back out of from the MasterCyl and to the Brakes. It is also the ABS motor all in one. The relay is under the hood at the Fuse/Relay center just inbetween the EBCM/ABS and AirIntake. Relays are big and square. The underside of the Fuse/Relay center cover has the ID and placement embossed into it of everything in the F/R center. Be sure to check the fuses first. The relay needs power to operate and the EBCM or ABS or Brake fuse will be the one for it. Good luck!

May 28, 2014 | 2000 Chevrolet Blazer

1 Answer

On my 2001 Chev Blazer 4.3 the secondary pump is new and comes on on cold start I'm still getting a p0410 code what could be causing this


check pump new doesnt mean free from defects also check the check valve can be damaged and lastly the fuse may be blown

Mar 31, 2013 | Chevrolet Blazer Cars & Trucks

1 Answer

2001 Chev blazer, brakes have been bled, peddle


You probably have air between the master cylinder and the abs pump. Fill the reservior and have someone pump the brake and bleed the primary lines at the abs pump. Good luck.

Apr 19, 2010 | 2001 Chevrolet Blazer

1 Answer

What is the size of the front caliper bolts on a 2001 chev. blazer


Full size 3/8 allen (socket head) T40 torx on the small blazer replacement bolts can be 8 MM allen

Aug 16, 2009 | 2001 Chevrolet Blazer

1 Answer

Need how to and location to replace knock sensor


Im looking for the same part location on a 2002 chevy blazer. It might be under the distributer cap.

May 30, 2009 | 2001 Chevrolet Blazer

1 Answer

2000 ABS relay location


Unfortunately the ABS relay is built into the EBCM. Electronic Brake Control Module. That is located on the frame rail, left side of vehicle and sits on top of the pump. Both parts are likely to be replaced together as getting the module off the pump can be difficult. I recommend a repair facility do this job but it can be done at home. You will likely need to take loose metal brake lines and that can be quite a task also.
Are you getting a code for the relay / EBCM?

Good luck
Please rate my answers if they helped.
Brett

Mar 20, 2009 | 2001 Chevrolet Silverado

1 Answer

Can't get transmission out 2001 chev blazer


did you take the short shaft loose? even if it were seized it would still come out.you may have to wiggle it back and forth a bit to work it loose but it should come out.

Jan 08, 2009 | 2001 Chevrolet Blazer

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

Related Topics:

646 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...