Question about 2004 Mercedes-Benz Mercedes Benz E Class

2 Answers

I am trying to wire a towbar on a 2004 Mercedes E class but I have no car wiring diagram. I need to know the wire colours. HELP!

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 33 Answers

You need to use a vehicle specific dedicated wiring kit (VSK) on this car, your local towbar specialist should be able to help. The problem's are that the car uses 1 wire for the side and brake lights, the rear fog and reverse lamps are controlled by a can bus module in the tailgate on the estate, but most importantly this car lights alternative lamps if a bulb fails. So if, for instance, the right hand indicator bulb fails, the car will flash the right hand reverse lamp, if a brake lamp fails the car will light the relevent fog lamp etc. It can be done without a VSK but it takes ages to wire up. So get a plug-in VSK it takes just five minutes to fit and it's all done, simples....

Posted on Oct 05, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 176 Answers

If you want to wire a towbar, I'd say, you can't wire a towbar, as a towbar is meant to be used to pull trailers, right? But, had you said I am trying to fit and wire a car trailer socket for my 2004 Mercedes E Class so I can plug a trailer plug for the trailer's taillights, etc. I would have understood what your needs are. Now, to fit and wire a socket to your Mercedes you need an testing tool costing less than UD$10.00. This tool it like a small screwdriver with a tip almost like a neddle and is used to punch into live sheaths of wires to see which wire is conducting (has power). This small tool is usually of plastic contruction and has a removable cap at the other end and has a length of wire with a small aligator clip at the other end of the wire. This aligator clip is clamped on a negative ( - ) surface, such as any exposed bolts or metal part of the engine or body of your car. The cap of this tool can also be unscrewed
to replace the small 12V light if it ever blows (fuses out). The overall reason of this tool is to be used to very carefully (and I mean it) pierce into any sheathed wires the check if any current is present when a particular action is being performed. The tool can be purchased at any reputable speed shop. Now, to begin with wire finding and assembly of the socket you need to first locate the braided (wrapped in a plastic tape) cable at the back part of the car, usually as close to the rear body (boot). After finding this cable (it has all the wires that control the tail lights, brake lights and reversing lights wrapped into 1 bundle), you now have to prepare a similar length of braided or prepacked cable that has wires inside expecially designed and coloured for use with most cars. In this care, if your Mercedes has different color wires, do not worry about it because you can mark them with a texta or special sticky take and write on them the different colors so that you wont become confused. Note that most speed shops sell rolls of cable specially for wiring car trailers. Just purchase a short length, depending on your requirements, unless you are to wire the whole trailer, I will discuss the objective of fitting and wiring the car with a trailer socket. Next, you may have to drill a hole where you want the cable to exit near the towbar (closest to the towball) and then you may have to decide where to screw the socket on the car, either on the lower part of its body or on a already welded plate especially fitted for the purpose of fitting a socket. This plate is usually closest to the towball. Now, lets start using the special tool to detect the current and noting down which wire is for brakes, tail light, reverse, etc. Go into the boot and locate the bundled cable. If it has a sheath, carefully cut it open and expose the 5 or 6 wires, depending on what country you are, each is different. Once you cut the sheath about 4 inches or more and have exposed the wires, try and separate them a little apart so you can work on them one by one. Now, here you need a helper to turn the parkers (lights) on, press the brake pedal to activate the brake lights, turn the ignition on but do not start the engine and put the gear selector into reverse (automatic or not), etc. Next, remove 2 or so inches of sheath from the purchased cable, spread the 5 or 6 wires apart and... if you have a wire stripper, so much the better, otherwise use a knife, being carefully not to cut or strip the copper strands in each wire. If you do, you'll have to start again. So be careful. if strands are not broken or snapped, you'll get full power to the trailer lights. If they're stripped or cut, the wires may get hot and probably cook themselves out at the point where the strands are missing. Remember, all strands must be twisted before use. Now put this aside for a moment and, with a helper to give you a hand for a few minutes, you first ask him/her to turn the lights on, then punch each exposed wires from the sheathed cable you found in the boot of your car and, with the poined part of this tool note which one has the current or power flowing that turn the car's tail lights on. Note the colour of this wire. You have a choice that you either strip this cable right away and then connect the twisted exposed copper wire, apply a solder with a soldering iron or make a good twist around the exposed wire in the boot that has the current flowing, mark this as (eg, Orange - tail lights) tail lights and then tape it with black automotive plastic tape, or you have the other choice that you puch all of the wires, locate their currents and which color is which for the following lights. I'd stick with the first option if I was you. So, next, ask your helper to depress the brake pedal and then again punch the sharp tip of the tool into the sheath of any of the other remaining wires (in the car boot that is) untill you locate the wire that has current to the brake lights. Once located (it is usually red colored), carefully strip it about half an inch and then bind the red wire from the purchased cable and either you solder it or you make sure it is a good wrap-around wirework and then wrap around this one as well with automotive insulating tape.
Repeat the process with finding the reversing lights wire in the boot by punching on the sheathed wire, carefully strip it, note the color and then bind around it a stripped and twisted wire from the purchased cable that has the same color, solder it if you have a solder. if not make sure the connection are wrapped around and tight, then tape the connection. After you've done all the wires (whatever wire is leftin the purchased cable, you either leave it unconnected or pull it out of the sheath and discard. Remember that there is usually a black wire running along into the mercedes sheathed cable. This wire should be considered as an Earth, or negative ( - ) wire. It should be also used because sometimes there is poor conduct between the car and trailer. Having this black, or negative wire connected as well will make sure you wont have a failure in connection with the car's electricity to that of your trailer. Usually, after turning the parking lights on or applying the brakes to activate the tail lights and this black wire doesn't have any current (the light on the tool does not come on after you have been punching every wire in the boot cable), it demonstrates that the black wire is negative. Now, after you have linked all the wires to that of the car wires and have insulated each of them, bend the purchased cable sideways with the car cable and retape it for a final insulation and to make sure the purchased cable stays bonded with the car cable. Pass the purchased cable through a small hole that is large enough to pass the cable but the right size to fit a grommet to seal out any dust. Now, after you have decided where you want to fit the socket, you now have to also decide if you want a round 5 pin socket or a flat 7 pin socket. Again, depending on your needs and use, I would recommend a 5 pin socket. Okay, having written down the colors of the wires used for parking lights/headlights, tail lights, reverse lights, left right indicators signals, etc., you now have to wire the socket before ataching it yo the body of your car or the plate of the towbar. Please take your time studying the wiring connection instructions that came with the socket packaging or box. Once wired, have your helper help you with turning the lights on, pressing the brake petal, turn the ignition on but don't start the engine and put the gearshift into reverse, turn the left or right signals. You can test all this by either clipping the aligator clip to an exposed chassis or clamp the clip directly behind the socket and on the black negative wire ( - ) then touch the socket pins with the pointed tip of the tool. If the tool's light comes on as each pin is touched and it is the correct sequence as per wiring instructions that came with the package and everything works accordingly, you can now install the socket to the car body or towbar plate. Now, you also have to make sure that the plug on the trailer is also wired accordingly to the pins of the socket on the car by orientating and checking if the pin that is for, say braking, is also the braking pin on the trailer plug. If this is too much for you, an automotive electrician is a better option because all you need do is make mistake and you'll cook your car's wiring.
Thank you. Michael. Automotive mechanic since 1973.

Posted on Sep 27, 2009

Testimonial: "Thank you, I have the tool to do the job and i am an electrical engineer (not a Cook) by trade so i understand the importance of getting it right."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Merrcedes-benz 200 wiring diagram


E class merc ing barrel wiring as some one changed it and the wires come out the plastic housing at rear 1994 car

Nov 29, 2009 | 1990 Mercedes-Benz E-Class

1 Answer

Need entire wire diagram for 1996 Ford Escort Lx


i want to wire up my towbar to a 1996 ford escort 5 door, i have the colur codes for which coloured wires come from 7 pin but need to know which coloured wires are for what on my car for rear light

Nov 08, 2009 | 1996 Ford Escort 4 Door

1 Answer

Wiring diagram and colour codes for an 2004 renault trafic towbar electrics


All of the wires you need are on a plug inside the left corner post behind a grommet behind the reverse light. The wires you need are best tested with a test lamp to identify them as there are wires with the same colours that have different functions, but if you put the lights on one at a time you can identify them with the test lamp

Sep 30, 2009 | 2004 Renault 181

1 Answer

Looking for towbar wiring diagram for MB W124.


You need to use a bypass relay on this car. the car colours are - L/Ind = Black/White, R/Ind = Black/Green, Fog = Grey/Green, Brake = Black/Red, Left tail = Grey/Black, Right tail = Grey/Red

Aug 31, 2009 | 1990 Mercedes-Benz E-Class

1 Answer

Ford focus c max towbar electrics


ARE YOU READY
L.H. STOP AND TURN ( YELLOW )
R.H. STOP AND TURN ( GREEN )
TAIL, LICENSE, SIDE MARKERS ( BROWN )
GROUND ( WHITE )
NOW THE COLORS ON THE VEHICAL ARE GOING TO BE DIFFERENT AND YOU WILL NEED A 12 VOLT TEST LIGHT FOR MAKEING SURE YOU HAVE THE WRITE WIRES FROM THE CAR TO THE TOE BAR, DON'T NEED BACK UP TIGHTS FOR THIS

Aug 25, 2009 | 2004 Ford Focus

1 Answer

Find me a wiring diagram


Use a Vehicle Specific Wiring Kit, it takes minutes to fit and plugs directly into the SAM unit on the left in the boot. You can do a lot of damage to this car by messing about with the wiring....

Jun 29, 2009 | 2002 Mercedes-Benz C-Class

1 Answer

E320 CDI 2001 W210 TOW BAR WIRING


Perhaps this link will be of help to you. http://www.watling-towbars.co.uk/towbars.html

Jun 12, 2009 | 1999 Mercedes-Benz E-Class

1 Answer

Towbar wiring for bmw x3


I dont know this particular model but if you go to a caravan sales pitch ,they usually have the wiring diagrams at the back of their caravan brochures. You could always tell them that you,re interested in getting a caravan but dont know if your car can be wired for one.Also try towbar sellers, they always give out the diagrams. Hope this helps.

May 20, 2009 | 2009 BMW X3

1 Answer

I need to wire a towbar to my lt 28 but have no wiring info


Trailer socket pin1 (yellow) to left hand indicator (Black/White) at L/H Lamp, Pin2 (blue) to fog (Grey/White) at R/H Lamp, Pin3 (white) to Chassis Earth, Pin4 (green) to right hand indicator (Black/Green) at R/H Lamp, Pin5 (brown) to right hand side light (Grey/Red) at R/H Lamp, Pin6 (red) to brake (Black/Red) at either Rear Lamp, and finally Pin7 (black) to left hand side light (Grey/Black) at L/H Lamp.

Mar 25, 2009 | 2004 Volkswagen Eurovan

Not finding what you are looking for?
Cars & Trucks Logo

708 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...