Question about 2000 Jaguar S-Type

1 Answer

Rear door window will not go up

Took door panel apart and can see a cable with square end just hanging, will i have to replace the regulator or could it of come out of its holder?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 92 Answers

Replace the regulator it is broken.

Posted on Sep 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace the rear passenger side window regulator in my 2001 dakota quad cab. I have taken it apart, removed the old regulator, and propped up the window


I had the same problem and found the broken lower cable guide laying in the bottom of the door. I drilled 2 holes thru the lower end of the regulator and remounted the guide with 2 screws. I then restrung the cable over the guides (not easy to do) and reinstalled the regulator in the door. It works like new.

Nov 23, 2011 | 2001 Dodge Dakota

1 Answer

How do you remove driver door panel ? the electric window broke, you can hear something rattling inside


Motor & Regulator
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Lower the window to the down position.
  3. Remove the door trim panel.
  4. Remove the door water deflector.
  5. Remove the window-to-regulator bolts.
  6. Push the window to its full up position and tape in place.
  7. Remove the nuts from the regulator cover plate.
  8. Remove the regulator drive cable from the rear of the cover plate and remove the cover plate from the door.
    32085_aler_g0158.gif

    Remove the nuts from the regulator cover plate

  9. Disconnect the electric connector from the motor.
  10. Remove the regulator bolts (1, 2, 3).
  11. Pivot the regulator (right door clockwise, left door counterclockwise) and slide the assembly out of the door.
  12. Remove the motor/regulator from the vehicle.
    32085_aler_g0159.gif

    Remove the regulator bolts (1, 2, 3) and remove the motor/regulator from the vehicle

To install:

  1. Partially install the three bolts (2) to hang the regulator in the door.
  2. Position the regulator in the door and hang it in place.

    NOTE

    Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the regulator bolts and tighten to 89 inch lbs. (10 Nm).
  4. Install the electrical connector to the motor.
  5. Slide the window down to join the regulator.
  6. Install the window to the regulator bolts and tighten to 89 inch lbs. (10 Nm).
  7. Install the regulator cover plate nuts and tighten to 89 inch lbs. (10 Nm).
  8. Install the regulator drive cable (1) to the rear of the cover plate.
    32085_aler_g0160.gif

    Install the regulator drive cable (1) to the rear of the cover plate

    NOTE

    The regulator drive cable goes into position (2) for the coupe and position (3) for the sedan.

  9. Check the operation of the window.
  10. Install the water deflector.
  11. Install the door trim panel.
hope this helps you
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 29; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Jan 15, 2011 | 2003 Pontiac Grand Am

1 Answer

Electric window feel down broken mechanism


Glass & Regulator

zjlimited_228.jpg

Fig. View of inner door frame and window regulator assembly

  1. Lower the window glass and remove the door panel.
  2. Carefully peel off the door screen so that it can be reused.
  3. Raise the window enough to reach the regulator bolts, hold the glass underneath and unbolt the glass from the regulator.
  4. To remove the glass, raise the glass by hand and tilt it as necessary to remove it from the track.
  5. To remove the regulator, lower the glass carefully to the bottom of the door and remove the bolts to remove the regulator.
  6. Installation is the reverse of removal. Tighten all bolts to 61 inch. lbs. (7 Nm).
zjlimited_229.jpg

Fig. Installing the door glass regulator



Motor

  1. Remove the door panel.
  2. Carefully peel off the door screen so that it can be reused.
  3. Unbolt the window from the regulator and carefully lower it to the bottom of the door.
  4. Disconnect the wiring and remove the motor mounting bolts.
  5. Remove the 3 guide rail bolts and lower the motor and guide rail assembly out the bottom of the door.
  6. Installation is the reverse of removal.
NOTE The upper cable must be below the guide rail mounting bracket.
Showing window regulator motor, or assembly carrier with window regulator, removal/installation

zjlimited_230.jpg

Fig.

NOTE The illustration shows the removal and installation of the window regulator motor/assembly carrier with the window regulator on the rear doors. The procedure for removing and installing on the front doors is the same.
zjlimited_231.jpg

Fig. Slide a hammer shaft between the window guide and the assembly carrier until the end of the hammer shaft presses against the assembly carrier. Remove the screws and take off the window regulator motor

  1. Slide a hammer shaft between the window guide and the assembly carrier until the end of the hammer shaft presses against the assembly carrier.
  2. Remove the screws and take off the window regulator motor.
To install:
  1. The gearing will move when the window regulator motor is removed; it is then no longer centered. The gearing must be aligned when the window regulator motor is installed until the window regulator motor is centered again.
  2. Installation is the reverse of the removal (see illustration).

Motor & Regulator

NOTE The illustrations in the procedure show the replacement of the window regulator motor/carrier assembly with window regulator for rear doors. The procedure for front doors is the same.
  1. Remove the front or rear carrier assembly.
  2. Slide a hammer handle between the window guide and carrier assembly until the hammer handle end presses on the gears of the carrier assembly.
  3. Unfasten the bolts (1) and remove window regulator.

    zjlimited_232.jpg

    Fig. Unfasten the bolts (1) and remove window regulator

To install:

NOTE By removing window regulator motor, gearing shifts, it is not centered.
zjlimited_233.jpg

Fig. By removing window regulator motor, gearing shifts, it is not centered

  1. When installing window regulator motor, the gears must be aligned until the window regulator motor is centered again.
  2. Attach and tighten the bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.
  3. Carrier assembly with window regulator, installing:
    1. For replacement part carrier assemblies, the gearing is secured in place with a cable tie.

      zjlimited_234.jpg

      Fig. For replacement part carrier assemblies, the gearing is secured in place with a cable tie (1)

    2. Slide a hammer handle between window guide and SF so far until hammer handle end presses on gears of SF.
  4. Remove the cable tie .
  5. By removing window regulator motor, gearing shifts, it is not centered.
  6. When installing window regulator motor, gears must be aligned until window regulator motor is centered again.
  7. Attach and tighten bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.

Hope this helps to solve it.

Dec 14, 2010 | 2002 Volkswagen Jetta TDI

2 Answers

Window regulator cable broke???


Here's a video that will show you how to replace the rear window regulator in that car.
">

Apr 03, 2010 | 2001 Chevrolet Impala

1 Answer

I have a 2000 Dodge Durango. My rear window on the drivers side has come loose and slid down inside the door. I took the door apart and found an unatached cable but I dont know where it snaps back on? Any...


sounds like the window regulator broke,u will need to replace the whole assembly,sometimes u can get them without the motor and change over the motor from your old window regulator to save a little cash

Sep 05, 2009 | 2002 Dodge Dakota Club Cab

1 Answer

Rear driver side window cable


Sorry but there is no fix but to replace the window regulator assy this is very common to break on these cars

Jul 27, 2009 | 1994 Mercury Grand Marquis

1 Answer

Window regulator replacement


Window Regulator, Rear Door, Explorer Removal
  1. Remove the rear door trim panel and watershield. Refer to Section 01-05B .
Trim Panel, Rear Door, Explorer, Hi-Series Four-Door Removal and Installation
  1. Remove the two screws retaining the rear door trim panel (27406) located above the door handle.
  1. Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.
  1. To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.
  1. Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .
  1. From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .
  1. At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.
  1. Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
    33c9359.gif
  1. If equipped with power windows, disconnect the wire from the regulator.
  1. Remove the rear door window glass as described in this section.
  1. Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.
  1. Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet. NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
  1. Using a 1/4-inch diameter drill, drill out the remainder of the rivet.
  1. Remove two upper regulator attaching nuts.
  1. Remove regulator from the front door (20125) .
Installation
  1. Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.
  1. Install regulator into access hole in inner panel.
  1. Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).
  1. Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).
  1. Install two upper regulator attachment nuts.
  1. Install door glass as outlined under Door Glass Installation.
  1. Adjust glass as outlined under Adjustments .
  1. Reconnect wire to regulator, if equipped.
  1. Check operation of window regulator.
  1. Install door watershield and trim panel. Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

Electric Window cable connections


unfortunatly there is no diagram or actual repair for a window regulator. the only fix is to replace the regualtor assembly. ive replaced hundreds of them at the jeep/chrysler/dodge dealer i work at

Jan 05, 2009 | 1999 Jeep Grand Cherokee

2 Answers

Electric window cable solution


My drivers side quit working. I took the door/window assembly apart and found that a small plastic clip had worn/broken. I modified it to hold the cable securely. The problem I had was knowing how the cables routed in the door and window assembly to put it back together. I found an online picture of a new one and routed my cables per the photo. It has not given me problems since. Time invested, about 3 hours. Cost was $0. If you buy a new one, cost is about $80 (online) and time would be about 2 hours. If you have the $$, buy a new one.

Oct 04, 2008 | 2002 Dodge Dakota Club Cab

1 Answer

Rear Passenger window won't roll up


No the only way to fix these wire regulators is replace them, they are fairly cheap, think about it, you pull the door panel, remove the regulator try to fix it and put it back, right away it fouls up, you have worked hard for nothing, replace it.

Aug 15, 2008 | 1992 Honda Accord

Not finding what you are looking for?
2000 Jaguar S-Type Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...